This version is for private use only and should not be distributed.
Mi Wireless Charging Pad
User Manual
Version: 1.0
This version is for private use only and should not be distributed.
Read this manual carefully before use, and retain it for future reference.
Product Overview
Mi Wireless Charging Pad is a universal wireless charger you can use at home or at work.
The charging base has a metallic finish, and a non-slip silicone material has been applied
to its top and boom surfaces. The wireless charger is equipped with a USB Type-C port.
Simply place your mobile phone on its surface to charge wirelessly.
USB Type-C Port
LED Indicator
User Manual
1. Please use the factory-supplied USB Type-C data cable with a power adapter, to
connect the Mi Wireless Charging Pad. Once connected, the product will be ready to
use aer the green LED has blinked three times.
Adapter Requirements:
a. 5 V/1 A adapters are not supported.
b. 5 W regular charging is supported by 5 V/2 A adapters.
c. 10 W fast charging is supported by QC 2.0/QC 3.0 adapters.
2. Place a Qi-compatible device in the center of the Mi
Wireless Charging Pad, to start charging
automatically. When the charger is in normal state
there is a constant green LED light.
01
This version is for private use only and should not be distributed.
3. Keep your phone centered on the Mi Wireless Charging Pad while charging. Adjust the
position of your phone if it is not charging, the green LED light should come on and your
phone's status should change to "Charging" (Please refer to figure below for placement).
4. If the LED light is blinking green, the Mi Wireless Charging Pad has encountered an error
and protective measures have been activated. Please check if any metal objects have
been placed on the charging pad. If so, please remove them and check if the pad
resumes charging. If the problem persists, please contact the sales staff.
Precautions
Do not put pressure on this product, and prevent any impact.
Do not disassemble nor modify it on your own.
Keep the product away from fire and do not submerge it in water.
Do not use the wireless charger in severely hot, humid or corrosive conditions to avoid
damage to the circuit.
Do not place cards equipped with a magnetic strip or chip (such as ID and ATM cards)
close to the product, in order to avoid possible card reading failures.
Keep a distance of at least 7.87 in between implanted medical devices (pacemakers,
cochlear implants, etc.) and the wireless charger, to avoid potential interference with the
medical devices.
This wireless charger is not a suitable children's toy, please keep it away from them.
In order to achieve a beer charging performance, please avoid using it in places with
high temperatures or lack of heat dissipation (such as bed sheets, mouse pads, etc.).
02
This version is for private use only and should not be distributed.
FCC Rule
This device complies with Part 18 of the FCC Rule.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Aention that changes or modification not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
product generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this product does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specifications
Product Name: Mi Wireless Charging Pad
Model: WPC01ZM
Input Port: USB Type-C
Input: 5 V 2 A / 9 V 1.6 A
Output: 5 V 5 W Max. 9 V 10 W Max.
Transmission Distance: ≤ 0.16 in
Operating Temperature: 32°F ~ 95°F
Manufactured for: Xiaomi Communications Co., Ltd.
Manufactured by: Zimi Corporation
(a Mi Ecosystem company)
Address: A913, No. 159 Chengiang Road, Jiangyin, Jiangsu, China
03
Loading...