Mi Air Purifier Pro H User Manual

Mi Air Purifier Pro H
User Manual

Warning

When the power cord is damaged, it must be replaced with a genuine power cord
purchased from the manufacturer or after-sales service department.

This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.

· Turn off and unplug the purifier before moving it.

· The purifier cannot turn on when the fan grille and the filter compartment cover are not installed properly.

· Maintain a distance of at least 20 cm between the air inlets and walls or other objects.

· Prior to cleaning or other maintenance, the appliance must be disconnected from the supply mains.

· Frequently remove dust, hair, and other particles from the outer mesh screen of the filter, so as to reduce the chance of bacteria growth.

· Remove dust, hair, and particles from the purifier's air inlets to prevent a reduction of air intake.

· Cover the air outlet to prevent dust, hair, and other particles from falling in when the purifier is left unused for a long time.

To avoid fire, electric shocks, or other damage, use the power cord and electrical outlet as instructed below:

· Do not excessively pull, twist or bend the power cord, as this may expose or break the cord's core.

· The power cord must be plugged into a suitable electrical outlet.

· Use the power cord that was provided with the purifier, do not use any third party power cords.

· Always unplug the purifier before carrying out maintenance to or moving the air purifier.

· Immediately stop using the purifier when it makes unusual sounds, gives off bad odors, overheats, or its fan rotates irregularly.

· Do not stick your fingers or foreign objects into the protective parts, movable parts, air inlets, or air outlets.

· Keep objects such as hairs or fabrics away from the purifier to avoid blocking the air inlets or air outlets.

· Do not sit on, lean on or tilt the purifier.

· When using in conjunction with gas-fueled appliances (such as gas stoves, gas heaters), please ventilate sufficiently to avoid carbon monoxide poisoning.

· Do not pour liquids, nor throw powders or other small substances into the purifier's air outlet.

· Make sure no inflammable objects get into the purifier.

Do not use the purifier in the following circumstances, as they may result in electric shocks, fire, or other damage:

· Near open flames, such as candles, incense burners, stoves, fireplaces, cigarettes, firecrackers, lighters, multi-purpose torches, candle lighters, or fire pans.

· Near appliances that generate high temperatures, such as electric heaters, fan heaters, electric foot warmers, electric stoves, electric irons.

· In unstable locations where the purifier can easily fall over.

· In environments that are extremely hot, humid, or damp, such as bathrooms.

1

Product Overview

Read this manual carefully before use, and retain it for future reference.
Note: Illustrations of the product, accessories, and user interface in this user manual are for reference purposes only. The actual product

and functions may vary due to product enhancements.

Top Grille

Temperature & Humidity
Sensor

Touchscreen

激光颗粒物传感器

LASER PARTICLE
SENSOR

Laser Particle Sensor

Filter Compartment Cover

Front Rear

2

Power Cord Port

Product Overview

Display

Brightness Adjustment Button

Power/Mode Button

Temperature

Humidity

Air Quality Indicator

One of the colors below will display according to the
PM2.5 value:

Green
Orange
Red

0 — 75
76 — 150
150

μg/m

μg/m

3

3

μg/m
or more

3

PM2.5 Value

Mode

Automatic: Automatically switch modes according
to the indoor air quality.

Night: Ultra-low noise for a comfortable sleeping
environment.

1: Low speed

2: Medium speed

3: High speed

Manual: Set and save the coverage area and
the purifying efficiency in the app.

Wi-Fi Indicator

3

Installation

Opening the filter compartment

Press the buckle to open the filter compartment, and
make sure the filter is installed correctly.

激光颗粒物传感器

LASER PARTICLE
SENSOR

激光颗粒物传感器

LASER PARTICLE
SENSOR

4

Placing the purifier in a suitable location

For optimal performance, make sure the distances
between the purifier and objects such as walls meet the
requirements as suggested below.

Connecting to an outlet

Connect the power cord to the port at the bottom of
the purifier, and then plug it into an outlet.

激光颗粒物传感器

LASER PARTICLE
SENSOR

20 cm or more

10 cm or more

20 cm or more

* The purifier is equipped with a sensor in the back. It is
recommended to maintain a certain distance between the
rear and objects such as walls during use.

Note: It is recommended to keep doors and windows
closed for a better purifying effect when using the
purifier.

5

Usage

Turning On/Off & Switching Mode

To turn on the purifier or change the mode, press the
button. To turn off the purifier, press and hold the button
for 2 seconds.

Resetting Wi-Fi

If your phone is unable to connect with the purifier,
simultaneously press and hold the Power/Mode and the
Brightness Adjustment buttons for five seconds. Once
you hear a beep, the Wi-Fi connection has been reset
successfully.

Adjusting Brightness

To adjust the brightness, press the button.

Bright

Dim Off

Connect with Mi Home / Xiaomi Home App

This product works with Mi Home / Xiaomi Home app*.
Control your device with Mi Home / Xiaomi Home app.

Scan the QR code to download and install the app.
You will be directed to the connection setup page
if the app is installed already. Or search "Mi Home /
Xiaomi Home" in the app Store to download and
install it.
Open Mi Home / Xiaomi Home app, tap "+" on the
upper right, and then follow prompts to add your
device.
*The app is referred to as Xiaomi Home app in
Europe (except for Russia). The name of the app
displayed on your device should be taken as the
default.
Note: The version of Mi Home app might have been
updated, please follow the instructions based on
the current app version.

6

Care & Maintenance

Make sure the purifier is turned off and unplugged.

Filter Status Notifications Cleaning the laser particle sensor

Use a non-sharp tool to open the cover of the laser
particle sensor, then use an air blow gun or hair dryer to
clean the sensor and the filter on the cover, as illustrated
in the figure.

Note: Do not use hot air.

Install an

genuine filter

1. Filter Installation Notification

No filter detected, or the installed filter is
not genuine.

2. Filter Life Notification

Filter remaining

90%

When the purifier detects that the filter's
service life is less than 10%, either unplug
and plug in the power cord again then turn
on the purifier, or open and close the filter
compartment then turn on the purifier,
the filter's remaining service life (in %) will
appear on the display.

3. Filter Replacement Notification

Filter remaining

2%

Note: The filter may produce odors when it absorbs excessive
harmful gases. It is recommended to store the filter in a place
with good lighting and ventilation to improve the activity of the
activated carbon and restore its particle adsorption capacity.
Please replace the filter when its recommended service life is due.

It is recommended to replace the filter every
10–14 months of use. If its service life is 10%
or less, the display will show the remaining
service life (in %) each time the purifier is
turned on.

Open the filter compartment
panel and horizontally pull the
strap to remove the filter.

Note: Refer to the Filter
Replacement instructions on the
inside of the filter compartment
cover.

Cleaning the filter compartment

Use a vacuum cleaner or a soft cloth to remove any dust
from the air inlets or the filter compartment, so as to
ensure optimal ventilation and purification.

Note: It is forbidden to directly rinse or spray the purifier with
water. Do not wipe the purifier with a soaking wet cloth to prevent
water from getting into it.

7

Specifications

Name Mi Air Purifier Pro H Rated Voltage 100–240 V~

Model AC-M13-SC

Item

Dimensions

Net Weight Approx. 9.6 kg Noise Level ≤65 dB(A)

Area Efficiency 200 m2/h

RF Specification:
Wi-Fi 2.4 G (2400–2483.5 MHz), Max. RF Output Power: <20 dBm
RFID (13.56 MHz), Max. Magnetic Field Strength: <60 dBμA/m@10 m
Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user.

*

Calculated according to standard GB/T 18801-2015

310 × 310 × 738 mm Rated Power 70 W

*

Wireless Connectivity Wi-Fi IEEE 802.11 b/g/n 2.4 GHz

Rated

Frequency

Color White

50/60 Hz

Clean Air Delivery Rate

(CADR Particles)

Formaldehyde Clean Air

Delivery Rate

(CADR Formaldehyde)

Particle Purification

Efficiency

Formaldehyde

Purification Efficiency

Network Standby Power

Consumption

600 m3/h

250 m3/h

High

High

< 2.0 W

8

Regulatory Compliance Information

Europe — EU declaration of conformity

Hereby, Beijing Smartmi Electronic Technology Co., Ltd. declares that the radio equipment type AC-M13-SC is in compliance
with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
http://www.mi.com/global/service/support/declaration.html

Disposal and recycling information

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should
not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over
your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed
by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the
environment and human health. Please contact the installer or local authorities for more information about the location as well
as terms and conditions of such collection points.

9

Manufactured by: Beijing Smartmi Electronic Technology Co., Ltd.
(a Mi Ecosystem company)
Address:Room 201-203, Unit 6, Building A, No. 66,Zhufang Road, Qinghe, Haidian District, Beijing
For further information, please go to www.mi.com
For detailed e-manual, please go to www.mi.com/global/service/userguide

Importer:
Beryko s.r.o.
Na Roudné 1162/76, 301 00 Plzeň
www.beryko.cz

V-20200713-Y