mhouse WG2S User Manual
MhouseKit WG2
S
For power-operated swing gate
Installation instructions and warnings, and User Manual
IS0003A00EN_28-03-2011
English – 1
English
GENERAL SAFETY WARNINGS AND PRECAUTIONS
STEP 1 2
KNOWLEDGE OF THE PRODUCT AND PREPARATION FOR
INSTALLATION
STEP 2 2
2.1 - PRODUCT DESCRIPTION AND INTENDED USE 2
2.2 - COMPONENTS USED TO SET UP A COMPLETE SYSTEM 3
PRELIMINARY CHECKS FOR INSTALLATION
STEP 3 3
3.1 - CHECKING SUITABILITY OF GATE TO BE AUTOMATED AND
RELATIVE ENVIRONMENT 3
3.2 - PRODUCT APPLICATION LIMITS 3
3.3 - PRODUCT DURABILITY 3
STEP 4 4
4.1 - PRELIMINARY CHECKS FOR INSTALLATION 4
4.2 - PREPARING ELECTRIC CABLES 4
INSTALLATION: ASSEMBLY AND CONNECTION
OF COMPONENTS
STEP 5 6
5.1 - INSTALLING THE GEARMOTOR WG1SK 6
STEP 6 6
6.1 - INSTALLING CL2S 6
6.2 - INSTALLING AND CONNECTING PHOTOCELLS PH100 7
6.3 - INSTALLING AND CONNECTING THE FLASHING LIGHT FL100 7
6.4 - ELECTRICAL CONNECTION TO CONTROL UNIT CL2S 7
PROGRAMMING
STEP 7 13
7.1 - POWER SUPPLY CONNECTION 13
7.2 - INITIAL CHECKS 13
7.3 - LEARNING CONNECTED DEVICES 13
7.4 - LEARNING THE GATE LEAF OPENING AND CLOSING ANGLES 13
7.5 - CHECKING THE RADIO TRANSMITTERS 13
7.6 - SETTING 13
TESTING AND COMMISSIONING
STEP 8 15
8.1 - TESTING 15
8.2 - COMMISSIONING 15
MAINTENANCE
STEP 9 15
PRODUCT DISPOSAL 15
FURTHER INFORMATION
STEP 10 16
10.1 - ADVANCED SETTINGS 16
10.2 - OPTIONAL ACCESSORIES 17
10.3 - ADDING OR REMOVING DEVICES 19
10.4 - MEMORIZING ALL RADIO TRANSMITTERS 20
10.5 - TROUBLESHOOTING 22
10.6 - DIAGNOSTICS AND SIGNALS 22
TECHNICAL SPECIFICATIONS OF PRODUCT
COMPONENTS 25
APPENDIX 1 - EC declaration of conformity 28
USER’S GUIDE
STEP 11 29
11.1 - SAFETY INSTRUCTIONS 29
11.2 - GATE CONTROL 29
11.3 - MANUALLY RELEASING OR LOCKING THE GEARMOTOR 29
11.4 - MAINTENANCE OPERATIONS ADMISSIBLE TO THE USER 30
11.5 - REMOTE CONTROL BATTERY REPLACEMENT 30
11.6 - REMOTE CONTROL BATTERY REPLACEMENT 30
APPENDIX 2 - EC declaration of conformity 31
CONTENTS
2 – English
English
GENERAL SAFETY WARNINGS AND PRECAUTIONS
• CAUTION! - Never power up the motor before fully installed
on the column and leaf of the gate.
• During installation, handle the automation with care, avoiding the risk of
impact, dropping or contact with any type of liquid. Never place the
product near to sources of heat and never expose to naked flames. This
may damage product components and cause malfunctions, fire or hazardous situations. If this occurs, suspend installation immediately and
contact the MhouseTechnical Assistance.
• Never make modifications to any part of the product. Operations other
than as specified can only cause malfunctions. The manufacturer
declines all liability for damage caused by makeshift modifications to the
product.
• If the power cable is damaged, it must be replaced exclusively by a
qualified technician, to avoid potential risks.
• Connect the control unit to an electric power line equipped with an
earthing system.
• This product is not designed to be used by persons (including children)
whose physical, sensorial or mental capacities are reduced, or with lack
of experience or skill, unless suitable instructions regarding use of the
product have been provided by a person responsible for safety.
• The key-operated selector switch must be positioned in sight of the
automation, but far from moving parts and at a height of at least 1.5 m
from the ground, not accessible by the public. If this is used in “hold-torun” mode, ensure that there are no persons in the vicinity of the
automation.
• In the vicinity of the automation children must be supervised to ensure
that they do not play with it.
• Ensure that there are not points of entrapment or crushing with fixed
parts when the gate leaf is in the maximum opening or closing position;
protect parts if necessary.
• The product may not be considered an efficient system of protection
against intrusion. If an efficient protection system is required, the
automation must be integrated with other safety devices.
• The automation must not be used before performing the commissioning
procedure as specified in the chapter “Testing and commissioning”.
• Check the automation frequently to ensure there is no imbalance, signs
of wear or damage to electrical or mechanical parts. Do not use the
automation if adjustments or repairs are necessary.
• In the event of long periods of disuse, to avoid the risk of leaks of harmful substances from the optional battery (PR1) disconnect it from the
automation and store in a dry location.
• Do not allow children to play with fixed control devices. Keep remote
control devices out of reach of children.
• The product’s packaging materials must be disposed of in full compliance with local regulations.
Operation warnings
• For cleaning the product surfaces, use a soft damp cloth. Use water
only; never use detergents or solvents for cleaning.
––– STEP 1 –––
Safety warnings
• CAUTION! – This manual contains important instructions and
warnings for personal safety. Incorrect installation could cause seri-
ous physical injury. Carefully read all parts of this manual before starting
any work. If in doubt, suspend installation immediately and contact the
Mhouse Technical Assistance.
• CAUTION! – Important instructions: keep this manual in a safe
place to enable future product maintenance and disposal procedures.
• CAUTION! – According to the most recent European legislation,
the production of a power-operated door or gate must comply with
the standards envisaged in the Directive 2006/42/EC (Machinery
Directive) and in particular standards EN 12445; EN 12453; EN
12635 and EN 13241-1, which enable declaration of presumed
conformity of the automation. In consideration of this, all mains
connection, testing, commissioning and maintenance operations
must be performed exclusively by a qualified and skilled technician.
All preliminary set-up, installation and programming operations
may be performed by personnel with standard skills, provided that
all instructions and the relative sequences in this manual are strictly observed, with particular reference to the warnings in this STEP
1.
Installation warnings
While reading this manual, take care to observe all instructions
marked with the following symbol:
These symbols indicate subjects that may be the source of potential
hazards and therefore the prescribed operations must be performed
exclusively by qualified and skilled personnel, in observance of
these instructions current safety standards.
• Before installation, ensure that this product is suitable for automation of
your gate or door (see STEP 3 and chapter “Product Technical Specifications”). If not suitable, do NOT proceed with installation.
• On the system power mains install a device for disconnection (not supplied), to guarantee a gap between contacts and complete disconnection in the conditions of overvoltage category III.
• All installation and maintenance operations must be performed
with the automation disconnected from the power supply. If the
power disconnect device is not visible from the location of the automation, before work a notice should be affixed on the disconnect device,
with the text “CAUTION! MAINTENANCE IN PROGRESS”.
KNOWLEDGE OF THE PRODUCT AND PREPARATION FOR INSTALLATION
––– STEP 2 –––
2.1 - PRODUCT DESCRIPTION AND INTENDED USE
The devices in this kit, plus other accessories (some optional and not
included in the pack), form the automation system named “WG2S”,
designed for the automation of a “residential” swing gate. Any other use
than as specified herein or in environmental conditions other than as
stated in this manual is to be considered improper and is strictly prohibited!
The main part of the automation comprises one control unit and two
electromechanical gearmotors, each equipped with a 24 V DC motor, a
worm reducer and a mechanical locking system with key to enable manual opening and closing of the gate in the event of a power failure.
The control unit comprises a board and incorporated radio receiver which
receives the commands sent by the user via a transmitter. It can memorise up to 256 GTX4 transmitters (if memorised in “Mode I”) and up to 6
pairs of PH100 photocells.
NOTES TO MANUAL
• This manual describes how to set up a complete and optimal
automation, such as that shown in fig. 6, using all Mhouse devices
that are part of the automation system named “WG2S”. Some of
these devices are optional and may not be present in the kit. For a
complete overview of the devices, refer to the MHouse product
catalogue.
• This manual has been drawn up as a step-by-step guide
. Therefore, to ensure safe and facilitated assembly and programming
procedures, perform all operations described in the same order as
specified in this document.
English – 3
English
- maximum weight 250 kg.
- opening angle up to 120°
The shape of the gate and weather conditions (such as the presence of
strong winds) may reduce these maximum values; in this case the user
must measure the torque required to move the leafs in the worst conditions, and compare this value with the technical specifications.
2 - Check the overall dimensions of the gearmotor (fig. 2). Note – These
measurements also serve as a reference to calculate the space occupied by the foundation pit for routing the electrical cable ducting.
3 - Ensure that the estimated lifetime is compatible with the intended use
(see paragraph 3.3).
4 - Ensure that all limitations, conditions and warnings in this manual can
be fully observed.
3.3 - PRODUCT DURABILITY
The lifetime is the average economic duration of the product. The value of
lifetime is strongly influenced by the intensity of the manoeuvres, i.e. the
sum of all factors that contribute to product wear, see Table 1. To estimate
the durability of your automation, proceed as follows:
01. Add up all the values in the items of Table 1;
02. In Graph 1 from the value obtained above, trace vertical line until it
intersects the curve; from this point trace a horizontal line until it intersects the line of the “manoeuvre cycles”. The value obtained is the
estimated lifetime of your product.
The lifetime values specified in the graph are only obtainable if the maintenance schedule is strictly observed (see chapter 9 - Maintenance schedule). The estimation of lifetime is made on the basis of design calculations
and the results of tests performed on prototypes. As it is only an estimation, it does not represent any form of guarantee on the effective lifetime of
the product.
Example of durability calculation: automation of a gate with a leaf length of
1.5 m with weight of 220 kg, for example, in a location subject to strong
winds. Table 1 states the “severity index” values for this type of installation: 10% (“Leaf length”), 25% (“Leaf weight”) e 15% (“Installation in windy
areas”).
These values must be added up to obtain the overall severity index, which
in this case is 50%.
With the value obtained (50%), check the horizontal axis of Graph 2
(“severity index”), for the corresponding value of “manoeuvre cycles”
which our product can complete in its lifetime = approx. 55,000 cycles.
Connection of the control unit with the various devices is by means of a
single 2-wire cable (“ECSbus” system). The control unit can also be
mains-powered (230 V) or alternatively by the Mhouse PF photovoltaic
system.
If powered from the mains, it can house a buffer battery (model PR1,
optional accessory), which ensures that the automation can perform a
number of manoeuvres for several hours in the event of a power failure.
During the power failure, or at any other time, the gate leaf can be moved
manually if required, by first releasing the gearmotor using the relative key
(see chapter 11.3 - User’s Guide).
2.2 - COMPONENTS USED TO SET UP A COMPLETE
SYSTEM
Fig. 1 illustrates all components used to set up a complete system, such
as that shown in fig. 6.
Components shown in Fig. 1:
A - 2 electromechanical gearmotors WG1SK with fixing brackets
B - 3 release keys
C - 1 pair of PH100 photocells (one TX and one RX)
D - 2 GTX4 radio transmitters
E - 1 FL100 flashing light with integrated aerial
F - 1 control unit CL2S
G -
Metal hardware
Notes:
- Some devices and accessories specified in the manual are optional and
may not be present in the kit. .For a complete description, refer to the
Mhouse product catalogue or visit the website
- The limit switch stops are not supplied in the pack and are not part of the
Mhouse product range.
––– STEP 3 –––
3.1 - CHECKING SUITABILITY OF GATE TO BE
AUTOMATED AND RELATIVE ENVIRONMENT
• Ensure that the mechanical structure of the gate complies with current
national standards and that it is suitable for automation. For this check,
refer to the information specified on the gate dataplate. Important -
This product cannot be used to automate a gate that is not already efficient and safe; furthermore it cannot solve defects caused by incorrect
gate installation or poor maintenance.
• Manually move the gate leafs in both directions (opening/closing) and
ensure that friction is constant throughout travel (there must be no
points of increased or decreased force).
• If the leaf is fitted in a pedestrian pass door or a door onto the leaf
movement area, ensure that this door does not obstruct normal travel,
and install a suitable interlock device if necessary.
• Manually move the gate to any position; leave it stationary and ensure
that it does not move when left.
• Ensure that the space around the site of gearmotor installation enables
safe and easy manual gate release.
• Ensure that the selected surfaces for installation of the various devices
are solid and guarantee a stable fixture; as regards photocells, select a
flat surface that guarantees correct alignment between photocells (Tx
and Rx).
• Ensure that all devices to be installed are in a sheltered location and
protected against the risk of accidental impact.
• Verify the overall limits with reference to fig. 2.
• Ensure that there is sufficient space also when the gate is open (fig. 3).
• On the basis of the leaf opening angle, check to ensure observance of
the positions in fig. 4 and Graph 2 (fig. 5).
• The bracket can be fitted in various ways (fig. 10): position “C” can vary
from 53 mm to 176 mm. It is normally approx. 150 mm.
• Position “D” is easily measured on the gate.
• Position “A” is the sum of “C” and “D”.
• On the basis of value “A”, and the leaf opening angle in the table, value
“B” can be calculated. For example: if “A” is 150 mm and the leaf opening angle is 115°, the value of “B” is approx. 160 mm.
It is recommended to select similar values for “A” and “B”. This guarantees regular movement of the leaf and minimal stress on the gearmotor.
3.2 - PRODUCT APPLICATION LIMIT
Before proceeding with installation, perform the following checks in the
specified sequence and ensure conformity both with the data in this paragraph and the technical data provided in the chapter “Technical Specifications”.
1 - Ensure that the dimensions and weight of the gate leafs are within the
following limits of use:
WG2S - maximum length 2.2 m
GRAPH 1
Severity index (%)
Manouvre cycles
Ambient temperature over 40°C or
lower than 0°C or humidity greater
than 80%
Solid leaf
Installation in windy zone
20%
15%
15%
TAB L E 1
Severity index
1 - 1,5 m
1,5 - 2,2 m
> 100 kg
> 200 kg
10%
25%
10%
25%
Leaf length
Leaf weight
125.000
100.000
75.000
50.000
25.000
4.2 - PREPARING ELECTRIC CABLES
To prepare all connection cables, proceed as follows:
a) - Refer to fig. 7 to check the connections of the various devices to the
control unit and terminals to be used for each connection. Important
- Only devices using “ECSbus” technology can be connected to the
terminal “ECSbus”.
b) - Refer to fig. 6 to check positions of the electrical cables in the area.
Then draw a similar diagram on paper, adapting it to specific requirements of your system. Note - This diagram will be useful to establish
the route of the raceways for cable ducting, and to draw up a complete list of the cables required.
c) - Read Table 2 to determine the type of cables to be used; then refer to
the diagram drawn above and on-site measurements to determine
the length of each cable. Caution! - No cable must exceed the
specific maximum length stated in Table 2.
WARNING - “ECSbus” technology enables the interconnection of devices
using a single “bus” cable, with 2 internal electrical wires. Connection of
several devices can be in the configuration “cascade”, “star” or the latter
two “combined”:
––– STEP 4 –––
4.1 - PRELIMINARY CHECKS FOR INSTALLATION
4.1.1 - Establish the position of devices in the system
With reference to fig. 6 and 7, locate the approximate position for installation of each device envisaged in the system. Fig. 6 shows a system made
using this product and other optional accessories in the Mhouse range.
These elements are positioned according to a typical standard layout. The
components are:
[a] - 1 CL2S control unit.
[b] - 1 FL100 flashing light with integrated aerial
[c] - 1 pair of PH100 photocells (one TX and one RX)
[d] - 1 KS100 key-operated selector switch
[e] - 2 photocell posts
[f] - 2 limit switch stops
[g] - 2 electromechanical gearmotors WG1SK
WARNING! - Some of these devices are optional and may not be
present in the kit (see Mhouse product catalogue).
WARNINGS:
The fixed control devices must be positioned:
- in sight of the automation;
- far from moving parts;
- at a height of at least 1.5 m from the ground,
- not accessible by the public.
4.1.2 - Establish the position of all connection cables
Refer to the instructions in paragraph 4.2 to establish the layout of the
raceways for electric cable ducting.
4.1.3 - Ensure all equipment and materials for work are available
Before starting work, ensure that you have all equipment and materials
required to complete the work. Ensure that all items are in good condition
and comply with local safety standards.
4.1.4 - Completing the set-up work
Prepare the area for subsequent installation of the devices, completing all
preliminary work, such as:
- digging of raceways for protection ducting of electric cables (external
ducting may be used as an alternative);
- laying of protection ducting and embedding in concrete;
- sizing of all electric cables to required length (see paragraph 4.2) and
routing in protection ducting. Caution! - In this phase, do not make
any electrical connections.
Warnings:
• The hoses and ducting serve to protect electrical cables and prevent
accidental damage in the event of impact.
• When laying pipelines, take into account the risk of possible deposits of
water in the branch wells, where condensate may form in the pipelines
and the control unit with possible damage to the electronic circuits.
• Position the ends of the ducting at the points envisaged for fixture of the
various components.
4 – English
English
cascade star combined
TABLE 2 – Technical specifications of electric cables
Connection Type of cable (minimum section values) Max. admissible length
A - Power line cable 3 x 1.5 mm
2
30 m (note 1)
B - FLASH flashing light output cable 2 x 0.5 mm
2
20 m
C - Radio aerial RG58 shielded cable type 20 m (less than 5 m recommended)
D - input/output ECSbus cable 2 x 0.5 mm
2
20 m (note 2)
E - STOP input cable 2 x 0.5 mm
2
20 m (note 2)
F - OPEN input cable 2 x 0.5 mm
2
20 m (note 2)
G - Motor output M1 and M2 cable 3 x 1 mm
2
10 m
Note 1 - If the power cable is longer than 30 m, a cable with a larger section is required (e.g. 3x2.5 mm
2
) and safety earthing is necessary in the
vicinity of the automation.
Note 2 - For cables of ECSbus and those of the STOP and OPEN inputs, a single cable with multiple internal wires may be used, to combine
several connections: for example, the STOP and OPEN inputs can be connected to the KS100 selector switch with a cable of 4 x 0.5 mm
2
.
CAUTION! – The cables used must be suited to the installation environment.; for example a cable type H03VV-F is recommended for
indoor environments, and a cable type H07RN-F for outdoor environments is recommended.
English – 5
English
2
100
729
45
392
85
4
B
D
A
C
GRAPH 2
5
1
F
B
E
DCA
G
3
150
min.
150
maxi
6 – English
English
INSTALLATION: ASSEMBLY AND CONNECTION OF COMPONENTS
––– STEP 5 –––
WARNINGS
• Incorrect installation may cause serious physical injury to those
working on or using the system.
• Before starting automation assembly, make the preliminary checks
as described in STEP 3.
5.1 - INSTALLING THE GEARMOTOR WG1SK
To secure the gearmotor, proceed as follows:
01. Select the fixing position, observing the specifications in paragraph
3.1 “Preliminary checks”;
02. Ensure that the fixing surface is perfectly smooth, level and sufficient-
ly compact. WG1SK is not supplied with fixing devices, which must
be chosen also on the basis of the fixing surface material.
03. Lay the duct for routing the electric cable (fig. 8);
04. To construct the rear supports, assemble the two brackets and rear
plate as shown in fig. 9;
05. The brackets and rear plate can be assembled in different ways: to
IMPORTANT!
- The following assembly phases show installation of a gearmotor
model WG1SK.
- To ensure correct system operation, mechanical stops must be
mounted on the floor or wall at the maximum leaf opening and closing
points. Note - These stops are not supplied in the pack and are not
part of the Mhouse product range.
obtain the various values of “C” see fig. 10;
06. To construct the front support, assemble the bracket and front plate
as shown in fig. 11;
07. Remove the rear cover of the gearmotor by loosening the two screws
in fig. 12;
08. Move the leafs to the closed position;
09. With reference to the previously calculated position “B” (fig. 4 and 5),
place the rear support on the fixing surface, in the envisaged position;
Caution! - check the positions in fig. 15.
10. Trace the drilling points of the rear support using the support as a ref-
erence Using a drill make four holes on the surface for insertion of 4
plugs of at least 8 mm (not supplied). Fix the plate with suitable
screws and washers (fig. 13);
11. Ensure that the plate is perfectly level (the slots on the bracket enable
small corrections to alignment, as shown in (fig. 14);
12. Place the front support as shown in fig. 15;
13. Provisionally secure the front support to the leaf with a clamp (fig. 16);
14. Lift the gearmotor and insert the fork in the hole of the front support;
15. Keeping the gearmotor raised, pull to open the leaf and align the hole
on the rear plate with the hole on the gearmotor. Fix the gearmotor to
the rear support [A] using screw [B], nut [C] and washer [D] (fig. 17);
16. Tighten the nut fully down then loosen by approx. half a turn to
enable rotation of the gearmotor on its support;
17. Secure the gearmotor to the front support, tightening the screw [E]
and washer [F], then tighten the screw fully down (fig. 18);
18. Unlock the gearmotor again using the release keys (see paragraph
11.3 - User’s Guide).
19. Test a number of manoeuvres moving the gate by hand. Check that
6
a
e f h
b c d
g
c
g
f
e
7
A
D
B C
ED F
D
G G
English – 7
English
the fork slides smoothly on the worm gear of the gearmotor and that
there are margins of at least 5 mm on the opening and closing limits,
while avoiding a situation in which an excessive section of the worm
gear is not used;
20. If necessary, adjust the limit switch of the gearmotor, loosening it by
means of the hex wrench [G] and moving it to the required position
(fig. 19). The mechanical opening limiter [H] is only used if there are
no limit stops present. The mechanical opening limiter [I] is only used
if there are no limit stops present. After adjusting the limiters tighten
the screws fully down:
21. Fix the front support permanently using screws suited to the leaf
material;
22. Unlock the gearmotor again using the release keys (see paragraph
11.3 - User’s Guide).
Make electrical connections. Refer to figure 24 and step 6.
––– STEP 6 –––
6.1 - INSTALLING CL2S CONTROL UNIT
01. Select the installation position in an area protected against potential
impact and in the vicinity of the gate, to reduce the overall length of
the cables;
02. Remove the cover, levering it off with a screwdriver from the opening
on the base; slide it by a few centimetres then lift it off the base (fig.
21);
03. Lay the duct for routing the electric cables so that they can be inserted from the lower section of the control unit;
04. Drill the lower side of the control unit and use special connectors for
securing the ducts for routing electric cables, as shown in fig. 22;
05. On the base, use a screwdriver to punch through the two holes; trace
the drilling points using the base as a reference (fig. 23);
06. Use a percussion drill to drill the wall, with a 6 mm tip, and insert 6
mm plugs.
07. Fix the base, using the relative screws [A];
08. Before closing the control unit, make the electrical connection with
reference to paragraph 6.6 and fig. 24.
09. To close the control unit, place the cover on the base by approx. 3
cm higher than the final position and push it downwards to engage it
completely, as shown in fig. 28.
6.2 - INSTALLING AND CONNECTING PH100 PHOTOCELLS
(fig. 29)
Warning: all installation operations must be performed with the system
disconnected from the power supply; if fitted, the PR1 backup battery
must also be disconnected.
Warnings: Take care not to damage the o-ring fitted (fig. 29-3) [A].
Select the position of the two elements making up the photocell (TX and
RX) observing the following:
• Place them at a height of 40-60 cm from the ground, to the sides of the
zone to be protected, and as close as possible to the edge of the gate,
i.e. no further than 15 cm.
• There must be a raceway tube at the point envisaged for routing cables.
• Point the transmitter TX at receiver RX with a maximum tolerance of 5°.
01. Remove the front glass panel (fig. 29-1).
02. Position the photocell at the point where the cable routing tube
arrives.
03. Trace the drilling points using the base as a reference. Use a percussion drill to drill the wall, with a 5 mm tip, and insert 5 mm plugs.
04. Route the electric cables through the specific holes (pierce those
required): see the two options in fig. 29-2.
05. Fix the base, using the relative screws [B] of fig. 29-3 ensuring that
the hole on the base [C] of fig. 29-3 is aligned with the cable outlet. 2
self-tapping screws are also supplied for fixture on surfaces with a
different density.
06. Connect the electrical cable in the relative terminals of both TX and
RX (fig. 29-4).Connect the electrical cable in the relative terminals of
both TX and RX (fig. 29-5) No polarity needs to be observed
.
07. Fix the covering shell [D] of fig. 29-6 with the two screws [E] of fig.
29-6 using a Phillips screwdriver. Lastly, insert the external cover [F]
in fig. 29-6 pressing it slightly to secure in place.
6.3 - INSTALLING AND CONNECTING THE FLASHING
LIGHT FL100 (fig. 30)
Select the position of the flashing light so that it is in the vicinity of the gate
in a visible location. It can be fixed on either a horizontal or vertical surface.
Fig. 30 shows the two options:
01. Remove the cover, unscrewing the screw if present.
02. Separate the base, unscrewing the screws present to route the elec-
tric cables.
03. Trace the drilling holes using the base as a reference and ensuring
that the hole on the base is aligned with the cable outlet: vertical fixture (A) or horizontal fixture (B).
04. Use a percussion drill to drill the wall, with a 6 mm tip, and insert 6
mm plugs.
05. Fix the base, using the relative screws.
06. Connect the electric cables in the relative FLASH and “aerial” termi-
nals as shown in the figure: To facilitate operations, remove terminals,
make connections, then refit the terminals.
No polarity needs to be observed on the FLASH terminal, while in the
case of the shielded cable connection of the aerial, the sheath must
be connected.
07. Insert the lamp holder in the base, taking care to press it down so
that it locks into place.
08. Secure the body of the flashing light to the fixing support and turn it
left until it clicks into place, then secure by means of the screw.
6.4 - ELECTRICAL CONNECTION TO CONTROL UNIT CL2S
To make the electrical connection, at very low voltage, of the various
devices, refer to fig. 24.
01. To connect the gearmotors: remove the gearmotor cover as shown
in fig. 20.
02. Loosen the cable clamp located below the gearmotor, route through
the electric cable, then tighten the cable clamp fully down (fig. 25).
03. Make the electrical connections observing the colour coding shown
in fig. 26.
04. Close the cover of the gearmotor.
At this point, make the electrical connections of the various devices
(see the paragraphs of the various accessories).
• The terminals have the same colour as the terminals on the correspon-
ding devices; for example the grey terminal (OPEN) of the KS100 keyoperated selector switch must be connected to the grey terminal (OPEN)
of the control unit;
• No polarity is needed for virtually any of the connections; only in the case
of the shielded cable of the aerial, the central core and sheath must be
connected as shown in detail [A] of fig. 24.
Notes: - To facilitate connections, terminals can be removed as shown in
fig. 27 - [A]; after making the connections, refit the terminals in their seats.
- - At the end of connections, use cable ties to secure the electric cables
to the relative fixtures (fig. 27 - [B]).
8 – English
English
8 9
11 12
13 14
10
15
600
34
English – 9
English
16 17
18 19
20
A
B
C
D
E
F
I
G
H
21
22
23
Loading...