Trainertec DTC1200V Remote Controlled Dog Training Collar
Operator’s Manual
www.mggproducts.co.nz
- 2 -
Thank you for choosing MGG Trainertec. We want to ensure your dog’s safety by providing you with the tools
and techniques to successfully train your dog.
If you have any questions please contact us by email info@mggproducts.co.nz or
visit our website at www.mggproducts.co.nz or freephone 0800 449 669
Please read the operator’s guide carefully before you start to train your dogs .
This instruction is suitable for Remote dog training collar DT1200V.
Components
How the System Works
The Remote Dog Trainer has been proven safe, comfortable and effective for all dogs over 5Kg in bodyweight.
This system assists you in controlling your dog at long range without a leash. At the push of a button the
Remote Transmitter sends a signal, activating the Receiver Collar worn by your dog. Using the Remote Trainer
consistently and correctly most bad habits that your dog exhibits can be corrected and any basic obedience
commands can be taught.
Important: The Remote Trainer actual operating range depends on the way you hold the Remote Transmitter.
Hold the Remote Transmitter in a horizontal position away from your body to achieve optimum range.
Terrain, weather, vegetation , Vehicles , Buildings, transmission from other radio devices and other factors
will affect the range of your Remote Trainer.
Main Features
1. The line of sight range is up to 1200 meters
2. Train up to 3 dogs from the same transmitter (additional collars available from MGG Products)
3. 10 levels of static shock
4. 10 levels of vibration
5. “Buzz” sound activated with a separate button
6. Two buttons “+” and “-” allow you to set your shock and vibration intensity
- 3 -
7. Dog Selection Button allows you to select your dog
8. LCD digital display for 10 shock & vibration levels and dog ID
9. Memorize shock & vibrate level in transmitter for different dogs
10. Easy to operate with rubber buttons.
11. Waterproof transmitter and receivers. Dogs can swim freely whilst wearing the collar.
12. Rechargeable 3.7V Li-ion battery for transmitter and receiver
13. Strong TPU Collar Strap
14. LED low power indication. A red light will flash when the battery level is low.
15. Full functional multi-dog training system
16. Around 8 seconds safe static shock protection
17. 2-year warranty
PLEASE CHARGE UP COLLARS AND REMOTE BEFORE USE. THE COLLARS AND REMOTE HAVE BEEN MATCHED
ALREADY FOR YOU BY MGG PRIOR TO DELIVERY.
Transmitter
“ ” and “ “ buttons: press these buttons to adjust the Static Shock intensity and Vibration intensity from
levels 1 to level 10
“ ” button: is the power switch. Hold this button for 4 seconds to switch on power then the LCD will
display the default “A01”. You may now change Dog ID by pressing the appropriate buttons. If you would
like to switch off the power, hold this button down for 4 seconds.
“ ” button: no-stimulation just a warning sound
“ ” button: emits a vibration stimulation. Press 1 time to vibrate 1 brief time. Press and hold to give
continuous vibration for up to 8 seconds. It will automatically cut out after the 8 seconds maximum.
Antenna
Stimulation
Level
On/Off
Button
Dog
Selection
Buttons
Led Light
LCD display
Buzz Button
Vibration
Button
Static
Shock
Button
DC Charging Jack Cover
- 4 -
“ ” button: Emit a static shock stimulation. Press 1 time to give one short shock . Press and hold on to give a
continuous shock. It will automatically cut out after the 8 seconds maximum.
“1,2,3 ” buttons: Dog Selection Button , default is “1” . Your transmitter is capable of training up to three dogs
with optional extra receiver collars.
Select dog 1 and the LCD displays dog ID “A XX”. If you want to train dog number 2 press the “2” button and
the LCD will display “BXX”. If you want to train dog 3 then press the “3” button and the LCD will display “C
XX”.
“XX” is for showing the shock & vibration level which you have set for each particular dog.
The transmitter has memory functions to save the selected shock & vibration levels for each different dog.
There are 10 levels of shock stimulation, 10 levels of vibration stimulation and one tone level.
PLEASE NOTE: The red Led light will flash when the battery is low. Please then re-charge the battery at once.
The Receiver Collar
NOTE: PLEASE CHARGE THE RECEIVER BEFORE FIRST USE
Setting Up A Multi-dog System
You can expand your one-dog Remote Trainer into a multi-dog Remote Trainer by yourself. Simply purchase
extra receiver collars and add them to your system. (Maximum 3 in total)
1. Matching a Receiver collar. To add a Receiver collar to your remote dog training system please follow the
these steps:.
Step 1 : Take out an unmatched receiver collar. Press and hold the “ON/OFF” button and after two “beep”
sounds then release. The receiver is now turned on and a green LED will flash frequently.
(Note : never open 2 or more unmatched receivers at the same time.)
Step 2 : Take out the transmitter that you want to match receiver to. Press and hold on “ ” button until the
LCD display turns on then release. The Transmitter is now on .
On/Off Button
Press and hold on 4 seconds to turn
the collar on. Two confirming tones
will sound and the collar’s green Led
light will flash once every 5 seconds.
Press and hold on for 4 seconds to turn
the collar off. One long tone will sound
and the green Led light will stop
flashing and turn off .
Please turn the collar off when not in
use to conserve the battery charge.
Contact Prong
Choose short or long
prongs to match the
dog’s coat type
Spanner
Change the Contact Prong s depending
upon your dog’s coat type .
Warning. If the Contact Prong is tight
and you continue to turn the spanner
clockwise then the Contact Prong will
break . Never turn the contact prong
too tightly .
LED Light
Indicate the working
status, Low battery ,
Charging status
You may have to cup
your hand over it to
see the dim light
DC Jack Cover
Open the Rubber
Cover and insert the
adaptor plug into DC
Jack to re-charge.
Thread the collar through the
side loops and around the back of
the receiver
- 5 -
Step 3 : Press and hold the “ ” button and the “ ” button at the same time until the digital number on the
LCD display changes automatically then release. The transmitter enters the “match receiver” mode .
The number changes like “08,09,10,11……”, increasing automatically .
Step 4 : Hold the transmitter close (50~100mm) to the unmatched receiver.
Step 5 : Press and hold the dog selection button which you want to match to. If you are matching dog “1”
then press the “1” button. If you are matching Dog “2” then press the “2” button etc.. After hearing
3 “beep” sounds from the receiver and seeing the green LED flash slowing down then release .
Special note: You must hear the 3 “beep” sounds from the receiver which you are matching first and
also see the green LED flash slow down before releasing the dog selection button. If your matching
fails you need to cancel the failed matched receiver then re-match again. (See 2 below to cancel)
Step 6 : Press and hold the “ ” button and the “ ” button at the same time again until the digital number
on the LCD display does not change, then release.
Step 7 : Test the matched Receiver. Choose the dog first, then press the “ ” button. You should hear the
“beep” sound from the matched receiver. Congratulations! You have matched the receiver
successfully .
Note: After matching a receiver collar the dog selection button will return to dog “1” by default .
Before testing the matched collar, please choose the correct dog number again first .
2. To cancel a matched Receiver please follow the steps below one by one.
Step 1 : Take out a matched receiver . Press and hold the “ON/OFF” button. After two “beep” sounds the
receiver is switched on and the Green LED flashes once every 5 seconds .
Step 2 : Press and hold the “ ” button until the LCD display turns on then release. The Transmitter is now
turned on.
Step 3: Press and hold the “ ” button and the “ ” button at the same time until the digital numbers on the
LCD display change automatically then release. You should now be in the cancel matched receiver
mode and see the number changing like “08,09,10,11……”, increasing automatically.
Step 4 : Hold the transmitter close (50~100mm) to the matched receiver. Press the Dog Selection Button once.
(You can press “1” or “2” or “3” freely, it is the same). You should hear 2 “beep” sounds from
receiver.
Step 5 : The green LED light of Receiver flashes frequently . Press and hold the “ ” button and the “ ”
button at the same time again until the digital number on the LCD display stops changing then release .
Exit the cancel matched receiver mode . Congratulations! You have cancelled the matched Receiver
successfully .
Charging
The transmitter and receiver charge rapidly – only around 2 hours are needed.
The transmitter and receiver collar can be charged at same time.
There is a common charger for the transmitter and receiver.
To recharge please open the Rubber Cover first . Plug the Adaptor into a household AC power outlet and insert
- 6 -
the Adaptor Plug into Receiver DC Jack .
Do not charge batteries in especially hot areas. Keep away from heaters etc.
1. Receiver Collar Charging
The red LED light is on when charging .
The green LED light is on and the red LED light is off when the receiver collar is fully charged.
The Receiver red LED light will flash when the battery is low. Please then re-charge the battery at once.
2. Transmitter Charging
The LCD display shows “CHA” when charging.
The LCD display shows “FUL” when the transmitter is fully charged.
The transmitter red light flashes if the battery is low. Please charge it promptly.
Important : When not in use for long periods, please give a full charge for transmitter and receiver collars
every month or so.
Training Guide
1. Fitting the Collar onto your Dog
Place the collar strap in the middle of the dog’s neck. The receiver should be on the underside of his neck
although on some dog’s necks the receiver will naturally seek a slightly off-center position. The Rubber Charging
Port Cover should face downwards ( toward the dog’s chest).
Tighten the buckle by holding it with two fingers as you pull the strap snug. Remote training collars must be
put on a dog quite snugly to ensure consistent contact of both probes on the skin of your dog’s neck to give a
reliable static stimulation.
2. Stimulation
Your Remote Trainer has 10 levels of intensity so you can find the best level for your dog’s temperament and
the type of training. You may also select either a shock or vibrate stimulation depending on your dog’s
temperament and your training purpose.
You may press the “+” or “-“ buttons to select a suitable shock level then press on the “ ” button one time to
give one short static shock or press and hold for around 8 seconds for a continuous stimulation. The shock
cuts out automatically after the 8 seconds maximum.
You may press the “+” or “-“ buttons to select a suitable a vibration intensity level then press and hold on the
“ ” button for around 8 seconds continuous vibration or press one time for one short vibration .
Troubleshooting Guide
Problem#1: No stimulation when a transmitter button is pressed.
The receiver has not been activated. The receiver must be turned on otherwise it won’t work at all.
The receiver has not been set to your transmitter. Follow the instruction to match. The intensity is set too low
or at zero.
Problem#2: The Beeper of Receiver doesn’t make any sound when the Receiver is turned on.
Press dog selection button to choose correct Dog ID before press transmitter buzz control button.
The Beeper component is loose. Please send to the MGG service center to repair .
Problem#3: The stimulation seems too high, not high enough or no feeling at all
The collar strap is not tight enough. Make sure the contact points connect properly with the dog’s skin.
The intensity level is not correct. Change the shock level.
- 7 -
The batteries are dead. Re-charging is needed.
Problem#4: The receiver light changes color to indicate low battery very quickly
The unit has been left turned on between training sessions and the battery has drained.
Make sure the receiver is turned off after use.
You are training in very cold weather.
Problem#5: The Remote Trainer doesn’t have range or the range is significantly reduced.
Either you or the dog is shielded by a metal structure. Operate it far away from these types of structures.
The receiver is on backwards. For the best range position the receiver so that the light faces toward the dog’s
nose with the charging port is facing the dog’s chest.
Radio Interference. Wait a short while then try again, or move to another area.
Problem#6: The receiver seems as if it can’t receive any signal or does not work at all
Check the receiver on/off button and make sure the receiver is turned on.
Check the transmitter to see if the battery is low. Charge transmitter first .
Cancel the receiver match and then re-match it with transmitter . If receiver does not work
either then please send it back to the MGG service center to repair or replace .
- 8 -
MGG Products, 29C Mill Lane, Kerikeri 0230, New Zealand
www.mggproducts.co.nz info@mggproducts.co.nz Ph. 09 401 6360
Loading...