MGA Entertainment 247845A Users manual

TRAINING YOUR COMMANDOBOT

CommandoBOT is trained to respond only to the Master. Therefore, you will need to train your CommandoBOT to recognize your voice for each of the 12 commands that the robot will follow. Your CommandoBOT will ask you to say each command twice. If the robot understands, it will go onto the next command. If not, the robot will ask you to repeat the command until it has 2 recordings that are similar in sound and speed.

You can use the command names that are programmed into the CommandoBOT or you can rename them as you train the CommandoBOT. For example, the CommandoBOT is programmed with the name “CommandoBOT” but you can call it a different name such as “Robot” or “Tommy”. The CommandoBOT will simply ask you to repeat the name to complete the training of that action.

Impor tant! In order for CommandoBOT® to follow your commands, it must recognize your voice and the

LOOK!

command matching the recordings acquired during training (word, sound, speed). Be sure to call out the commands the same way you trained them.

1. To begin training your CommandoBOT to recognize your

voice, press and hold the MODE button microphone on the headset) for 3 seconds.

2. CommandoBOT will request that you begin to say the

commands so it can recognize your voice.

— Position microphone so that it is close enough to pickup your

voice, but not so close that your breathing overrides the commands.

(above the

Setting "Room Guard" Secret Code

—

The Robot has factory preset secret Code "1 2 3 4" You can change your new Secret Code at below: Press PRG and 6 then press "1 2 3 4" and EXE to erase the factory preset secret code. You will hear a "beep" tone. Enter your new 4 digit secret code and press EXE to confirm.

3. CommandoBOT will say “CommandoBOT”.

4. You need to say

choose for your CommandoBOT.

5. The CommandoBOT will say “Repeat”.

6. Repeat the name again exactly as you spoke it before.

IMPORTANT:

— If the CommandoBOT does not understand, you will hear an

error message such as “Did not compute” or “Too loud” and then the CommandoBOT will ask you to repeat the command.

— Train the CommandoBOT in a quiet environment and play in

same condition.

7. The CommandoBOT will move on to the next command

when it has understood the last voice command you gave it. Repeat steps 3 thru 6 for each command.

8. You will train your CommandoBOT to recognize the

following action commands:

Commandobot

Forward

IMPORTANT:

— Robot will ask you to repeat the command words 2 times.

After completing the Training mode, your

CommandoBOT will automatically go through a System Check .

Back

Left

Right

Halt

“CommandoBOT”

Fire Gun

Laser

Launch Tomahawk

Missiles

Toggle lights

System Check

or whatever name yo

Keypad

1 = Fire Gun 2 = Forward 3 = Laser 4 = Left

(keypad direction)

5 = Stop

(keypad direction)

6 = Right 7 = Missiles 8 = Back 9 = Tomahawk PRG = Program CLR = Clear EXE = Execute

Programming Missions

Your CommandoBOT can carry out five different missions. Missions 1-4 are preprogrammed. To reprogram Missions 1-4 or to program Mission 5:

1. On your CommandoBOT’s keypad, press

by the mission number you wish to program, for example

—

You will hear a beep.

2. Using the keypad, enter in the sequence of commands

for that mission. You may enter up to 20 commands.

PRG

3. Press EXE to save your new mission.

IMPORTANT:

—

If you make a mistake will entering your mission, press This will exit you from mission programming and save the previously stored mission.

— Mission 5 will run immediately after you press

will not respond to voice commands.

EXE

. Mission 5

followed

CLR

USING YOUR COMMANDOBOT

Now that you have your CommandoBOT trained to recognize your voice, you are ready to command it to move and shoot. The procedure is simple: say the command as you said it during training and wait for your CommandoBOT to respond and answer you before giving the next command.

For example, to have your CommandoBOT move forward.

1. You say “

robot.

CommandoBOT”

or whatever you named the

2. Your CommandoBOT responds "Beep" and Action.

3. You say

4. Your CommandoBOT will responds "Beep" and move

IMPORTANT:

•

• You must speak clearly and use the same intonation as you did

• When your CommandoBOT is unable to understand your

• When you repeatedly make mistakes in giving the voice

• Once you have completed the basic CommandoBOT training,

Sleep Mode

If you have not given a voice command to your CommandoBOT in 2 minutes, the robot will go into Sleep Mode. To wake up your CommandoBOT, press the MODE button once on your headset briefly and say "CommandoBOT" or what ever name you choose before to continue play. .Do not press and hold the mode button more than 3 seconds.)

Room Guard Mode

To activate the room guard, press EXE and 6 button to start the person enters the room. When your Commandobot detects motion, you will hear a short beep for 15 seconds for you to enter the 4 digit secret code and EXE to disable the siren.

A siren will sound for 30 seconds if you do not press the

correct 4 digit secret code and EXE button within 15 seconds.

Walkie Talkie Mode

Position your CommandoBOT in a place where you want to be heard but not seen.

Press the TALK switch on your headset to activate WT mode speak through your headset to the people near your CommandoBOT. NOTE: Press the talk button 1 second then start to talk.

“Forward”.

forward.

You must say "CommdoBOT" (or whatever you named the robot) first, and then wait for it to respond "Beep" before giving any voice commands.

when you trained your CommandoBOT. If you get too excited and speak quickly or differently than when you trained your CommandoBOT, it will not understand you.

command, it will an error message such as “Did not compute. Repeat” or “Too loud. Repeat”.

commands or your CommandoBOT is unable to pick up what you said after 3 tries, you will hear a ‘beep, beep’ sound. Try again, speak clearly and say “ to reactivate.

every time you turn on your headset your CommandoBOT will go through its System Check.

“Room Guard” mode.

CommandoBOT”

To sound its siren if an unidentified

(or its new name)

IMPORTANT:

— Your CommandoBOT can not move when in WT mode. — Walkie Talkie range is up to 50 feet.

Missions

Your CommandoBOT can carry out five different missions. Missions 1-4 are preprogrammed (you can reprogram them

- see Programming Missions). Mission 5 must be programmed by you to run mission.

Running Missions

Press EXE and then the mission number.

All Missions will not respond to voice command.

—

Reset

If, at any time, your CommandoBOT goes out of control, press the RESET button on it’s back (next of Power ON/ OFF switch) once. Your CommandoBOT will return to normal.

Important Operating Tips

You can not independently operate more than one

CommandoBOT at the same time. (If they are same frequency Channel)

You can stop your CommandoBOT in motion by pressing the MODE button on the headset briefly once. Be careful! If you press and hold the MODE button for longer than 3 seconds, your CommandoBOT will go back to the training mode and you have to redo the entire Training procedure.

Optimum operating distance is 3 feet. Maximum operating range is up to 50 feet indoors. However, this may vary depending on environmental conditions.

You do not have to retrain your CommandoBOT after replacing the batteries.

You are the only master of your CommandoBOT. Any new user will have to retrain the voice commands in order to operate the CommandoBOT.

Your CommandoBOT can be trained with different language commands. It is advisable that you assign distinguishable voice commands in order not to confuse your CommandoBOT.

If it is responding slowly or malfunctioning, it is time to replace the batteries.

RESTORE THE FACTORY PRESETS

Press and hold the PRG key and slide the power switch to

ON at the back of Robot until the arm lights lit, release the PRG key and wait about 2 seconds, you will hear a beep tone to confirm the factory setting is done.

THIS RESETS THE "ROOM GUARD" SECRET CODE AND ALL MISSIONS.

Rev. 0