MFJ MFJ-904H User Manual
MFJ-904/904H Deluxe Travel Tuner Instruction Manual
INTRODUCTION
The MFJ-904/904H Travel Antenna Tuner was specially compact-built with
great features. The MFJ-904 has a Cross-Needle SWR/Wattmeter, 50 ohm SO239 connectors and a tuner/bypass switch. The MFJ-904H adds a binding post
for random wire and binding post with a 4:1 balun for balanced lines.
You can operate 80 through 10 Meters -- anywhere with any transceiver -- use
any coax fed, random wire or balanced line antenna. It’s great for mobile, base,
backpack, etc. The MFJ-904/904H handles 150 watts RF output.
INSTALLATION
The MFJ-904/904H should be installed between the transmitter and antenna.
1. Locate the tuner in a convenient location at the operating position.
2. Use a 50 ohm coaxial cable to connect the transmitter or transceiver to the
SO-239 labeled TRANSMITTER on the back of the tuner.
3. Connect an antenna feed to the appropriate tuner output:
a.) COAX-FEED to the SO-239 connector labeled ANTENNA.
b.) RANDOM WIRE
MFJ-904: A random wire may be used by connecting to the center of
the SO-239 connector with the supplied plug.
MFJ-904H: Connect to the red binding post labeled WIRE.
The MFJ-904/904H must be grounded when using a random wire.
c.) BALANCED FEEDERS (MFJ-904H only) to the red binding posts
labeled BALANCED LINE. When using a balanced feedline, connect a
short jumper from the WIRE binding post to the closest balanced line
post (see labeling on back of unit).
4. Connect your tuner and transmitter to a good earth ground.
OPERATION
This tuner has a BYPASS/TUNE switch located on the back of the unit. Simply
place the switch toward the BYPASS labeling to completely bypass the tuning
circuit. Change the switch toward the TUNE labeling to place the tuning circuit
between the transmitter/transceiver and the antenna.
In this tuner the TRANSMITTER and ANTENNA matching controls have
maximum capacitance at position 0 (fully meshed), and minimum capacitance at
1
MFJ-904/904H Deluxe Travel Tuner Instruction Manual
position 10 (fully open). Be sure to use the highest possible capacitance for
each band. This will provide the smoothest tuning, highest efficiency, and
greatest power handling capability.
The INDUCTANCE switch has maximum inductance in position "A", and
minimum inductance in position "L". Less inductance is needed as the
frequency is increased. If too little inductance is used, the tuner may not match
the load properly. If too much inductance is used, the tuner will be "touchy",
power handling will be compromised (capacitors could arc, etc.) and the
bandwidth will not be as wide.
Special Note: Always use the minimum amount of inductance as possible.
Minimum inductance gives the best efficiency, maximum power
handling, and widest bandwidth.
The MFJ-904/904H covers 80 through 10 meters. Do not operate on 160
meters.
SWR/Wattmeter:
The built-in SWR/Wattmeter measures forward and reflected power and
indicates SWR. The It has 2 power scales which are selected with the front
panel push button switch. The low power scale reads from 0-30 watts forward
and 0-6 watts reflected. The high power scale reads from 0-300 watts forward
and 0-60 watts reflected. SWR is indicated from 1:1 to ∞.
The MFJ-904/904H has an illuminated meter. To provide power for the meter
lamp, a 12 Vdc supply such as the MFJ-1312D should be used. Use a standard
2.1 mm coaxial plug with the center conductor positive and the sleeve ground.
To measure forward and reflected power press the selector switch to the correct
power setting. Transmit a steady carrier and read the power from the meter.
Each unmarked picket on the scale is an even division between the adjacent
marked values. SWR is read from the SWR curve closest to where the meter
needles cross.
Tuning Procedure:
1. Position the TRANSMITTER control to 5 on the corresponding scale.
2. Position the ANTENNA control to 0 on the corresponding scale.
3. Place the BYPASS/TUNE switch in the TUNE position.
4. Apply just enough power to obtain noticeable deflection on the reflected
power meter or SWR meter.
2
Loading...