MFJ-5000 Portable Function Generator
Typical Specifications:
Frequency Range...............................≈1 Hz - >150 kHz in 3 ranges
Amplitude Range............................... 0 to ≈4 Volts p-p (fixed square wave—
Waveform Output.............................. Sine, Triangle, or Square
Power Source.....................................Internal (9V battery), External (9-15 Vdc)
Current Drain.....................................10 mA
Size....................................................2.9" x 4.0" x 1.6"
Weight............................................... Approximately 8 oz.
Jack and Controls:
MFJ-5000
Portable Function Generator
1
dependent on power supply voltage)
2
Amplitude Frequency
3
5
9-15 VDC
Power
+
-
Off
6
X1 X100
Multiplier
7
4
X10K
8
1. Amplitude Control: Adjusts sine/triangle waveform output level.
2. Frequency Control: Adjusts waveform frequency.
3. Waveform Switch: Selects between sine and triangle waveform.
4. Multiplier Switch: Turns power on, selects frequency multiplier (X1-X10K).
5. External Power: Coaxial power jack accepts 2.1mm plug (9-15 Vdc).
6. Ground: Common connection for sine/triangle and square wave outputs.
7. Sine/Triangle: Output terminal for sine or triangle waveforms.
8. Squarewave: Output terminal for square waveform.
Powering Your Generator
:
1. Battery Installation: Remove panels screws and gently lift generator from case. Find
battery snap-clip and slide plastic sleeve down power lead. Snap battery onto clip and
install in carrier. Replace generator in cabinet.
Important Note:
Avoid storing for extended periods with a battery installed. When
removing battery, reinstall insulating sleeve on snap-clip.
2. External Power source: Power from any well-filtered 9-15 Vdc source. The external
power jack accepts a 5.5-mm x 2.1-mm coaxial plug (extras available--RadioShack
274-1567 or equivalent). Connect (+) voltage to center terminal, and (-) to common:
-
-
+
+
Operating Tips:
1. Frequency Control: The Frequency control and Multiplier switch provide the
following coverage:
Multiplier Frequency Setting
Switch Minimum Maximum
X1
X100 45 Hz 6 kHz
X10K 2 kHz >150 kHz
≈≈≈≈
1 Hz
130 Hz
2. Waveform Selection: The Waveform switch selects between sine-wave output
(switch up) and triangle-wave output (switch depressed). Output level is controlled by
the Amplitude potentiometer. Maximum output is around 3 volt p-p with a 9-volt
power source (greater with higher supply voltage). Square wave output is fixed at
approximately the power supply voltage (square-wave function has a separate output
terminal).
3. Audio Lines: The MFJ-5000 is an unbalanced "line-level" device. For driving mic-
level inputs, make a simple attenuator using two fixed-value resistors (this will bring
the generator's Attenuator control into useful range). For checking high-level balanced
lines, use an isolation transformer and float the generator, as shown:
Sine
Gnd
560 56K
Unbalanced Mic-Level
Gnd
600-600
Xfmr
Sine
Balanced
Line Level
Maintenance:
Your MFJ-5000 is inherently trouble-free, but switches or controls may sustain damage if
the unit is dropped or ex posed to harsh vibration. Also, avoid exposure to rain, snow,
extreme heat, or other severe environmental conditions. If you experience a problem,
always check battery condition first. If battery replacement fails to resolve the problem,
you may contact MFJ Technical Service by phone at 662-323-0549; by fax at 662-3236551; or by email at techinfo@mfjenterprises.com. Be sure to include a complete
description of the difficulty.