MF Digital Signature IV Inkjet User Manual

Scribe EC with Signature IV Printer
Installation Guide

SCRIBE EC WITH SIG IV INSTALLATION GUIDE

Minimum PC System Requirements

A Pentium II/III PC 800 MHz or faster
Windows 2000 Pro (Service Pack 4) or Windows XP
512 MB Ram
7200 RPM ATA-100 Clean Hard Disk NTFS - (5GB Free Space)
800 x 600 display, 16-bit color recommended
Two Button Mouse
Two Free PCI Slots
1 external COM port (COM1 or COM2) - 2 ports needed if using Prism
Plus or Spectrum2
Win ASPI driver layer (Included)
IEEE-1394s adapters (Included) (Except print Station)
Appropriate IEEE-1284 Printer Cable if attached
Document Revision: 2/21
MF DIGITAL
121 Carolyn Blvd.
Farmingdale, NY 11735
001 631 249 9393
www.mfdigital.com

IF YOU PURCHASED A PRINT STATION – SKIP THIS PAGE

Installing the Firewire Adapter Card

The internal configuration of your computer may be different from the computer pictured below.
One and two drive ScribeECs require one IEEE-1394 card. Four drive systems require two IEEE-1394 cards.
1. Shut down the PC.
2. Turn the PC’s power off.
3. Unplug the PC.
4. Remove the PC’s cover as indicated in the PC’s manual.
5. Locate an empty PCI slot, as seen in (fig.1).
6. Install the firewire adapter card (fig. 2).

Installing the Drive Bay

1. Place the drive bay onto the base unit as seen in (fig. 1).
2. Position the drive bay so that the front right corner sits over the dotted line (fig. 2). Proper position is shown in (fig. 3).
(fig.1)
(fig. 2)(fig. 1)
(fig. 2) (fig. 3)
Page 2
Preparing the Primera Sig IV Printer
m

What’s In The Box

Signature IV printer
Signature IV printer adapter plate
Power adapter
Printer software CD
Color ink cartridge
Spare ink cartridge holder
Warranty statement and registration card
Operator’s manual

Installing the Primera Sig IV Printer Adapter Plate

1. Using needle nose pliers, remove the rubber feet from the bottom of the printer (fig. 1).
2. Screw the printer plate to the botto of the inkjet printer as seen in (fig. 2).
(fig. 1)
(fig. 2)
Page 3
Making the Connection

1 & 2 Drive Systems 4 Drive System

PC Connection

Two drive unit uses one fire wire adapter card and one cable.
Four drive unit uses two firewire adapter cards and two cables… Install one cable in each firewire card.
Page 4

Installing the SCRIBE EC Software

1. Insert the SCRIBE EC software CD.
2. From the CD ROM drive of
the computer, click Install SCRIBE Software.
3.
Click Next (fig. 1).
4. Accept the license agreement and click Next (fig. 2).
5. Click Install (fig. 3).
6. Click Finish (fig. 4).
(fig. 1)
(fig. 2)
(fig. 3)
(fig. 4)
Page 5
Installing the SCRIBE EC Alignment Utility
1. Insert the SCRIBE CD into the CD­ROM drive of your PC.
2. Click on setup.exe of the alignment utility and Click OK (fig. 1).
3. Click the button indicated in (fig. 2).
4. Enter a name for the group where the Alignment Utility will be located. Click Continue (fig. 3). The Scribe Program Utility will appear under Start / Programs / ”group name” after installation is complete.
5. A progress bar will appear (fig. 4).
6. Click OK (fig. 5) to finish installation.
(fig. 1)
(fig. 2)
(fig. 3)
(fig. 4)
(fig. 5)
Page 6
Installing the Primera Sig IV Printer Driver
1. Click Start-> Settings-> Printers
2. Click Add New Printer
3. The “Welcome to the Add Printer Wizard” window will appear (fig 1). Click Next.
4. In the “Local or Network Printer” window, uncheck the “Automatically detect installed printer” option , leaving the “Local printer attached to computer” option (fig 2) and click Next..
5. In the “Select a Printer Port” window, leave the default as LPT1 (fig 3) and click Next.
6. In the “Install Printer Software” window, click the “Have Disk” button (fig 4). You will then be prompted to “Install from Disk”, click the “Browse” button (fig 5). Select the location of the printer driver from your CD-ROM drive in the PC (fig 6).
fig 1
fig 2
fig 3 fig 4
fig 5
fig 6
Page 7

Installing the Primera Sig IV Printer Driver (cont.)

7. After specifying the driver for the Sig IV printer, the printer “CD Color Printer IV” will appear in the “Add Printer Window” (fig 7). Click Next to continue.
8. In the “Name your Printer” window, leave the printer as the default name, and select the printer to be the default printer (fig 8) and click Next.
9. In the “Printer Sharing” window, select “Do Not Share the Printer” (fig 9) and click Next.
10. Say No to “Print Test Page” (fig 10) and click next.
11. The “Completing the Add Printer Wizard” window will appear (fig 11). Click Finish. After clicking finish, the Sig IV printer driver will be installed. You will be asked to accept that the printer driver is not digitally signed by Microsoft, click Continue (fig 12). You have now successfully installed the printer.
fig 7
fig 8
fig 10
fig 9
fig 11
fig 12
Page 8

Adjusting the Primera Sig IV Printer Driver Settings

P
P
rinting Preferences
To change the printing preferences for the Signature PRO printer, please do the following:
1. Go to Start-> Settings -> Printers
2. Right-click on the CD Color Printer PRO printer in the Printers Folder
3. Go to Printing Preferences
4. For the Scribe Program to use the printer effectively, please match the settings of your printer driver to the example on the right-side of this page.
5. To save settings, click Apply and OK to exit.
***NOTE: Any changes made to the printer driver settings, require a NEW PRN file to be made. If you change one of the settings, be sure to create a NEW PRN file.***
rinter Spooling
It is important to disable printer spooling on the Signature PRO printer. To do so, please follow the steps below:
1. Go to Start-> Settings -> Printers
2. Right-click on the CD Color Printer PRO printer in the Printers Folder
3. Go to Properties
4. Go to the Advanced Tab
5. For the Scribe Program to use the printer effectively, please match the settings of your printer driver to the example on the right-side of this page.
6. To save settings, Click Apply and OK to exit.
***NOTE: Any changes made to the printer driver settings, require a NEW PRN file to be made. If you change one of the settings, be sure to create a NEW PRN file.***
Page 9
Aligning the Drive Tower
C
d
d
r
r
d
1. From your Start Menu Open the SCRIBE E Alignment Utility (fig. 1). It will be located in the folder designated when you installed the alignment utility. Choose the appropriate COM Port which the Scribe EC Loader is installe on. Select all other printers and drives, an Click Start Test.
Follow the instructions by opening the top
2.
CD/DVD drive tray, and Clicking Yes (fig. 2). The picker arm will hover a disc over the drive tray, observe the discs position and make the adjustments to the drive tower (fig. 3).
Click Yes when you are satisfied with you
3.
adjustment (fig. 4).
4. The picker arm will then place the disc onto the drive tray. Follow the on screen instructions and click OK (fig. 5).
5. Once you are satisfied with the drive towe alignment, tighten the thumb-screws locate on both sides of the drive tower (fig. 6).
(fig. 1)
(fig. 2)
(fig. 3)
(fig. 4)
(fig. 5)
(fig. 6)
Page 10
Aligning the Primera Sig IV Printer
C
p
d
r
t
r
f
p
Alert:
1. From your Start Menu Open the SCRIBE E
2.
3.
4. After restarting the Scribe EC Software
5. A Printer Alignment Box will appear. First,
6.
7.
Before starting the Alignment Utility, position the front end of the printer on the dotted line on the top of the drive bay.
Software.
Once the Scribe EC Software opens, click on the Settings tab.
Click Change Settings and select the MF Digital Signature IV Printer. After making this selection, you will need to restart the Scribe EC Software program.
rogram, go to the Settings Tab. You will now see a button that says “Test Loading an Unloading the Printer”. Click button. (fig 1)
you will click the “Pick up a disc from the Input spindle and put it down on the printe tray” (fig 2). Adjust the printer so that the CD is aligned in the printer tray (fig 3).
After ensuring proper placement of the CD on the printer, continue with the Alignmen Utility and pick up the CD from the printe tray.
After you are satisfied with the alignment o the CD on the printer tray, lock the printer in
lace by tightening the thumb screws on the printer plate to hold the printer in place.
(fig. 1)
(fig. 2)
(fig. 3)
Page 11
Loading...