SCRIBE EC with OptiEC PRO PRINTER INSTALLATION GUIDE
Minimum System Requirements
Print Station & 1-Drive Models – Minimum System Requirements:
• Minimum Pentium® III or compatible personal computer @ 800 MHz or faster.
• Windows 2000 Professional (Service Pack 4 or higher) or Windows XP Professional
(Service Pack 1.0a or higher)
• 512MB RAM
• 7200 RPM ATA-100 hard drive with 850 MB for CD-R or 5GB (NTFS) for DVD-R
of free hard disk space - fully defragmented.
• Monitor: 800 x 600 display, 16-bit color recommended.
• Two button mouse.
• High quality recordable CD-Rs / DVD-Rs
• *One free PCI slot for DVD system, two free PCI slots for CD system (refer to
Appendix A).
• One external COM Port (COM1 or COM2) for the ScribeEC loader.
• IEEE-1394 B Adapter (Included).
*USB to Serial Converter can be used if COM port is not available.
•
2-Drive & 4-Drive Models – Minimum System Requirements:
• Minimum Pentium® 4 or compatible personal computer @ 2 GHz or faster.
• Windows 2000 Professional (Service Pack 4 or higher) or Windows XP Professional
(Service Pack 1.0a or higher)
• 1GB RAM
• 7200 RPM ATA-100 hard drive with 850 MB for CD-R or 5GB (NTFS) for DVD-R
of free hard disk space - fully defragmented.
• Monitor: 800 x 600 display, 16-bit color recommended.
• Two button mouse.
• High quality recordable CD-Rs / DVD-Rs.
• *One free PCI slot for DVD system, two free PCI slots for CD system (refer to
Appendix A).
• One external COM Port (COM1 or COM2) for the ScribeEC loader.
• IEEE-1394 B Adapters (Included).
• *USB to Serial Converter can be used if COM port is not available.
MF DIGITAL
121 Carolyn Blvd.
Farmingdale, NY 11735
001 631 249 9393
www.mfdigital.com
Page 2
Page 3
t
r
ScribeEC with OptiEC PRO printer
333
Scribe EC Quick Installation Guide
Installation Guide
with Prism PLUS Printer
IF YOU PURCHASED A PRINT STATION – SKIP THIS PAGE
Mounting the Firewire Adapter Card
DVD dive ScribeEC requires only one PCI
firewire B controller card (IEEE-1394B).
For additional information on making the
firewire connection refer to Appendix A.
1. Shut down the PC.
2. Turn the PC’s power off.
3. Unplug the PC.
4. Remove the PC’s cover as
5. Locate an empty PCI slot, as
6. Install the firewire adapter card (fig. 2).
The internal configuration of your computer may be different from the computer picture below
(fig. 1)
indicated in the PC’s manual.
seen in (fig.1).
(fig. 2)
Document Revision: 2004/12/07
Document Revision: 2004/12/28
Installing the Drive Bay
1. Place the drive bay onto the base unit as seen in
(fig. 1).
2. Position the drive bay so that the front righ
corner sits over the dotted line (fig. 2). Prope
position is shown in (fig. 3).
(fig. 2) (fig. 3)
(fig.1)
Page 3
Page 4
ScribeEC with OptiEC PRO printer
444
Scribe EC Quick Installation Guide
Installation Guide
with Prism PLUS Printer
Document Revision: 2004/12/07
Document Revision: 2004/12/28
Making the Connection
1 & 2 Drive Systems have one firewire B cable connection (IEEE-1934B).
4 Drive Systems have two firewire B cable connections (IEEE-1934B).
POWER
CABLE
USB CABLE
TO PC
POWER
CABLES
SERIAL
CABLE TO PC
PRINTER INTERFACE
CABLE BETWEEN A
LOADER AND A PRINTER
FIREWIRE
CABLE TO PC
(IEEE-1394)
PC Connection
Power cable
Serial cable
to a loader
USB cable
to a printer
Note:
*Firewire cable
to a drive bay
Page 4
For additional information
on the firewire connection
refer to Appendix A
Page 5
ScribeEC with OptiEC PRO printer
555
Scribe EC Quick Installation Guide
Installation Guide
with Prism PLUS Printer
Installing the SCRIBE EC Software
1. Insert the SCRIBE EC
software CD.
2. From the CD ROM drive of
the computer, click Install SCRIBE Software.
3. Click Next (fig. 1).
4. Accept the license agreement
and click Next (fig. 2).
5. Click Install (fig. 3).
6. Click Finish (fig. 4).
Document Revision: 2004/12/07
Document Revision: 2004/12/28
(fig. 1)
(fig. 2)
(fig. 3)
(fig. 4)
Page 5
Page 6
ScribeEC with OptiEC PRO printer
666
Scribe EC Quick Installation Guide
Installation Guide
with Prism PLUS Printer
Installing the SCRIBE EC Alignment Utility
1. Insert the SCRIBE CD into the CDROM drive of your PC.
2. Click on setup.exe of the alignment
utility and Click Next (fig. 1).
3. Choose the setup type that best suits
your needs, then click Next (fig. 2).
4. Click Install (fig. 3).
5. A progress bar will appear (fig. 4).
6. Click Finish (fig. 5) to finish
installation.
Document Revision: 2004/12/07
Document Revision: 2004/12/28
(fig. 1)
(fig. 2)
(fig. 3)
(fig. 4) (fig. 4)
Page 6
Page 7
ScribeEC with OptiEC PRO printer
777
Scribe EC Quick Installation Guide
Installation Guide
with Prism PLUS Printer
Installing the OptiEC PRO Printer Driver
1. Click Start-> Settings-> Printers
2. Click Add New Printer
3. The “Welcome to the Add Printer Wizard”
window will appear (fig. 1). Click Next button.
4. In the “Local or Network Printer” window,
uncheck the “Automatically detect installed
printer” option, leaving the “Local printer
attached to computer” option (fig. 2) and click
Next button.
5. In the “Select a Printer Port” window, select
USB001 port (fig. 3) then click Next button.
6. In the “Install Printer Software” window, click
the “Have Disk” button (fig. 4). You will be
then prompted to “Install from Disk”, click the
“Browse” button (fig. 5). Browse the location
of the printer driver on a CD (fig. 6).
Document Revision: 2004/12/07
Document Revision: 2004/12/28
(fig. 1)
(fig. 2)
(fig. 5)
(fig. 6)
(fig. 3)
(fig. 4)
Page 7
Page 8
ScribeEC with OptiEC PRO printer
888
Scribe EC Quick Installation Guide
Installation Guide
with Prism PLUS Printer
Installing the OptiEC PRO Printer Driver (cont.)
7. After specifying location of a driver for the
OptiEC PRO printer, the printer “CD/DVD Printer 6” will appear in the “Add Printer
Window” (fig. 7). Click Next to continue.
8. In the “Name your Printer” window, leave
the printer as the default name, and select the
printer to be the default printer name (fig. 8)
and click Next.
9. In the “Printer Sharing” window, select “Do Not Share the Printer” (fig. 9) and click
Next.
10. Choose No for “Print Test Page” (fig. 10)
then click Next.
11. The “Completing the Add Printer Wizard”
window will appear (fig. 11). Click Finish.
12. Click on Continue Anyway button to proceed
(fig. 12).
13. You have now successfully installed the
printer driver for OptiEC PRO printer.
Document Revision: 2004/12/07
Document Revision: 2004/12/28
(fig. 7)
(fig. 9)
(fig. 8)
(fig. 10)
(fig. 11) (fig. 12)
Page 8
Page 9
ScribeEC with OptiEC PRO printer
999
Scribe EC Quick Installation Guide
Installation Guide
with Prism PLUS Printer
Adjusting the OptiEC PRO Printer Driver Settings
Printing Preferences
To change the printing preferences for the OptiEC
PRO printer, please do the following:
1. Go to Start-> Settings -> Printers
2. Right-click on the CD/DVD Printer 6 in
the Printers Folder
3. Go to Printing Preferences
4. For the Scribe Program to use the printer
effectively, please match the settings of
your printer driver to the example on the
right-side of this page.
a. Ink Cartridge setting depends on
installed cartridge.
5. To save settings, click Apply and OK to
exit.
***NOTE: Any changes made to the printer
driver settings, require a NEW PRN file to be
made. If you change one of the settings, be sure
to create a NEW PRN file.***
Document Revision: 2004/12/07
Document Revision: 2004/12/28
Printer Spooling
It is important to disable printer spooling on the
OptiEC PRO printer. To do so, please follow the
steps below:
1. Go to Start-> Settings -> Printers
2. Right-click on the CD/DVD Printer 6
printer in the Printers Folder
3. Go to Properties
4. Go to the Advanced Tab
5. For the Scribe Program to use the printer
effectively, please match the settings of
your printer driver to the example on the
right-side of this page.
6. To save settings, Click Apply and OK to
exit.
***NOTE: Any changes made to the printer
driver settings, require a NEW PRN file to be
made. If you change one of the settings, be sure
to create a NEW PRN file.***
Page 9
Page 10
C
d
r
r
d
ScribeEC with OptiEC PRO printer
101010
Scribe EC Quick Installation Guide
Aligning the Drive Tower
1. From your Start Menu Open the SCRIBE E
Alignment Utility (fig. 1). It will be located in
the folder designated when you installed the
alignment utility. Choose the appropriate COM
Port which the Scribe EC Loader is installe
on and Click Start Test.
Follow the instructions by opening the top
2.
CD/DVD drive tray, and Clicking Yes (fig. 2).
The picker arm will hover a disc over the drive
tray, observe the discs position and make the
appropriate adjustments to the drive tower (fig.
3).
Click Yes when you are satisfied with you
3.
adjustment (fig. 4).
4. The picker arm will then place the disc onto
the drive tray. Follow the on screen
instructions and click OK (fig. 5).
5. Once you are satisfied with the drive towe
alignment, tighten the thumb-screws locate
on both sides of the drive tower (fig. 6).
Installation Guide
with Prism PLUS Printer
Document Revision: 2004/12/07
Document Revision: 2004/12/28
(fig. 1)
(fig. 3)
(fig. 3)
(fig. 4)
(fig. 6)
Page 10
(fig. 5)
Page 11
p
r
f
C
k
r
ScribeEC with OptiEC PRO printer
111111
Scribe EC Quick Installation Guide
Installation Guide
with Prism PLUS Printer
Aligning the OptiEC PRO Printer
Document Revision: 2004/12/07
Document Revision: 2004/12/28
Alert:
1.
Before starting the Alignment Utility,
osition the back end of the inkjet printe
in line with the dotted line on the top o
the drive bay.
From the Start Menu Open the SCRIBE EAlignment Utility. It will be located in the
folder designated when you installed the
alignment utility. Choose the appropriate COM
Port Number, which the Scribe EC Loader is
connected to then choose the OptiEC then
Click the Start Test button (fig. 1).
2. Follow the onscreen instructions then Clic
Yes button (fig. 2). The picker arm will then
hover a disc over the open printer tray.
Observe disc’s position and make the
appropriate adjustments to the printer (fig. 3).
3. Click Yes when you are satisfied with you
adjustment (fig. 4).
4. The picker arm will then place a disc onto the
printer tray. Follow the on screen instructions
then click the OK button (fig. 5).
5. Once you are satisfied with the printer’s
alignment, tighten the thumbscrews located on
both side of the printer (fig. 6).
(fig. 1)
(fig. 2)
(fig. 5)
(fig. 6)
(fig. 3)
(fig. 4)
Page 11
Page 12
ScribeEC with OptiEC PRO printer
121212
Scribe EC Quick Installation Guide
Installation Guide
with Prism PLUS Printer
Document Revision: 2004/12/07
Document Revision: 2004/12/28
Appendix A
DVD8Z-9001EC, DVD8Z-9002EC
1 and 2 DVD drive system requires only one PCI firewire B controller card (IEEE1394B) to be installed in a host PC. One firewire B cable is connected between a host PC
and a drive bay.
DVD8Z-9004EC
4 DVD drive system requires only one PCI firewire B controller card (IEEE-1394B) to
be installed in a host PC. Two firewire B cables are connected between a host PC and a
drive bay. Both of the firewire B cables are plugged into one PCI firewire B controller
card (IEEE-1394B).
CD-9001EC, CD-9002EC
1 and 2 CD drive system requires one PCI firewire A controller card (IEEE-1394) to be
installed in a host PC. One firewire A cable is connected between a host PC and a drive
bay.
CD-9004EC
4 CD drive system requires two PCI firewire A controller cards (IEEE-1394) to be
installed in a host PC. Two firewire A cables are connected between a host PC and a
drive bay. One firewire A cable is connected to one firewire A controller card.
Firewire B (IEEE-1394B)
Firewire A (IEEE-1394)
A picture shows ports of firewire A and B.
A picture shows a firewire B cable. A picture shows a firewire A cable.
Page 12
Page 13
ScribeEC with OptiEC PRO printer
131313
Scribe EC Quick Installation Guide
Installation Guide
with Prism PLUS Printer
Troubleshooting
1. The ScribeEC program did not recognized the loader.
a. Check the power cable on the back of the ScribeEC loader.
b. Make sure the power switch on the power supply of the loader is in ON
position (the I is pressed in).
c. Make sure the power switch on ScribeEC loader is turned ON.
d. Check the serial cable (RS232) connection between the ScribeEC loader
and the host PC.
2. ScribeEC program did not recognize any drives.
a. Press the eject button on the drive to check for power.
b. Check the power cable on the back of the drive bay.
c. Turn the power button on the drive bay. The power button is located on
the front of the tower.
d. Check the firewire connection between the drive bay and the host PC.
e. Check if Windows operating system recognized the drives by going to My
Computer or Device Manager. Windows operating system must initialize
the drives prior to executing the ScribeEC program.
3. ScribeEC program did not recognize printer.
a. Make sure the power is turned ON to the printer.
b. Make sure the ScribeEC program is set for OptiEC PRO printer.
c. Check the USB cable connection between the printer and the host PC.
d. Check the printer interface cable connection between the printer and the
ScribeEC loader.
e. Manually eject the printer tray then execute the ScribeEC program.
Document Revision: 2004/12/07
Document Revision: 2004/12/28
Page 13
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.