Mettler Toledo PANTHER, PANTHER DIGITOL, PANTHER ANALOG User Manual



Terminal

User’s Guide

D14945800A

(4-02)

©Mettler-Toledo, Inc. 2002

No part of this manual may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose without the express written
permission of Mettler-Toledo, Inc.

U.S. Government Restricted Rights: This documentation is furnished with Restricted Rights.

CUSTOMER FEEDBACK

Your feedback is important to us! If you have a problem with this product, or just a suggestion on how we can serve you
better, please fill out this form and send it to us. If you are in the United States, you can mail this postpaid form to the
address on the reverse, or fax it to [phone]. If you are outside the United States, please apply the appropriate
amount of postage before mailing. You can also send your feedback via email to: [e-mail]

Your Name: Date:
Organization Name: METTLER TOLEDO Order Number
Address: Part / Product Name:
Part / Model Number:
Serial Number:
Phone Number: ( ) Fax Number: ( ) Company Name of Installation:
E-mail Address: Contact Name:
Phone Number:

How well did this product meet your
expectations in its intended use?
Met and exceeded my needs
Met all needs
Met most needs
Met some needs
Did not meet my needs

PROBLEM:
UNACCEPTABLE DELIVERY: OUT OF BOX ERROR:

Shipped late Wrong item Wrong documentation
Shipped early Wrong part Missing documentation
Shipped to incorrect location Missing equipment Incorrectly calibrated
Other (Please Specify) Equipment failure Other (Please specify)

Comments:

Comments:

DO NOT WRITE IN SPACE BELOW; FOR METTLER TOLEDO USE ONLY

Retail Light Industrial Heavy Industrial Systems

RESPONSE: Include Root Cause Analysis and Corrective Action Taken.

.

E

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 414 COLUMBUS, OH

POSTAGE WILL BE PAID BY ADDRESSE

Mettler-Toledo, Inc.
Quality Manager - MTWI
P O Box 1705
Columbus, Ohio 43240
USA

FOLD THIS FLAP FIRST

Please seal with tape.

NO POSTAGE

NECESSARY IF

MAILED IN THE

UNITED STATES

DECLARATION OF CONFORMITY

Konformitätserklärung

Déclaration de conformité

Declaración de Conformidad

Conformiteitsverklaring

Dichiarazione di conformità

We/Wir/Nous/Wij/Noi: Mettler-Toledo, Inc.
1150 Dearborn Drive
Worthington, Ohio 43085
USA

declare under our sole responsibility that the product,

erklären, in alleiniger Verantwortung, daß dieses Produkt,
déclarons sous notre seule responsabilité que le produit,
declaramos, bajo nuestra sola responsabilidad, que el producto,
verklaren onder onze verantwoordelijkheid, dat het product,
dichiariamo sotto nostra unica responsabilitá, che il prodotto,

Model/Type: Panther

to which this declaration relates is in conformity with the following standard(s) or other normative document(s).

auf das sich diese Erklärung bezieht, mitder/den folgenden Norm(en) oder Richtlinie(n) übereinstimmt.
Auquel se réfère cette déclaration est conforme à la (aux) norme(s) ou au(x) document(s) normatif(s).
Al que se refiere esta declaración es conforme a la(s) norma(s) u otro(s) documento(s) normativo(s).
Waarnaar deze verklaring verwijst, aan de volende norm(en) of richtlijn(en) beantwoordt.
A cui si riferisce questa dichiarazione è conforme alla/e sequente/i norma/e o documento/i normativo/i.

in combination with a weighing platform produced by Mettler-Toledo is in conformity with the following directives and standards.

Council directive on the harmonization of the laws of the Member states: standards:

relating to non-automatic weighing instruments (90/384/EEC) amended by directive
(93/68/EEC)

relating to electromagnetic compatibility (89/336/EEC) amended by directive
(93/68/EEC; 92/31/EEC)

relating to electrical equipment designed for use within certain voltage limits
(73/23/EEC amended by directive (93/68/EEC)

Worthington, Ohio USA, November, 2000 Mettler-Toledo, Inc.

Darrell Flocken, Manager - Weights & Measures
Office of Weights and Measures

Original issue: January, 1997
Revised: February, 1997 added compliance to Non-automatic Weighing Instrument Directive
November, 2000 added compliance to Heavy Industrial Immunity, EN 50082-2

EN 45501:1992

EN 55022, B

EN 50082-2

EN 60950

According to EN 45014

INTRODUCTION

This publication is provided solely as a guide for individuals who have received Technical Training in
servicing the METTLER TOLEDO product.

Information regarding METTLER TOLEDO Technical Training may be obtained by writing to:

METTLER TOLEDO

1900 Polaris Parkway

Columbus, Ohio 43240

Phone (US and Canada): [phone]

Phone (International): [phone]

FCC Notice

This device complies with Part 15 of the FCC Rules and the Radio Interference Requirements of the
Canadian Department of Communications. Operation is subject to the following conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at his or her own expense.

This manual correctly describes the operation and functionality of the PANTHER terminal containing
software versions as follows. The software number is displayed during the power-up sequence.

Model Software Number Revision

PANTHER Analog G14891100A L7.1

PANTHER Analog C15379000A L3.1

PANTHER DigiTOL E14988700A L5.1

METTLER TOLEDO RESERVES THE RIGHT TO MAKE REFINEMENTS OR

CHANGES WITHOUT NOTICE.

PRECAUTIONS

READ this manual BEFORE
operating or servicing this
equipment.

FOLLOW these instructions
carefully.

SAVE this manual for future
reference.

DO NOT allow untrained
personnel to operate, clean,
inspect, maintain, service, or
tamper with this equipment.

ALWAYS DISCONNECT this
equipment from the power
source before cleaning or
performing maintenance.

CALL METTLER TOLEDO for parts,
information, and service.

WARNING

ONLY PERMIT QUALIFIED PERSONNEL TO SERVICE THIS EQUIPMENT.
EXERCISE CARE WHEN MAKING CHECKS, TESTS AND ADJUSTMENTS THAT
MUST BE MADE WITH POWER ON. FAILING TO OBSERVE THESE
PRECAUTIONS CAN RESULT IN BODILY HARM AND/OR PROPERTY
DAMAGE.

WARNING

FOR CONTINUED PROTECTION AGAINST SHOCK HAZARD CONNECT TO
PROPERLY GROUNDED OUTLET ONLY. DO NOT REMOVE THE GROUND
PRONG.

WARNING

DISCONNECT ALL POWER TO THIS UNIT BEFORE REMOVING THE FUSE OR
SERVICING.

CAUTION

BEFORE CONNECTING/DISCONNECTING ANY INTERNAL ELECTRONIC COMPONENTS OR
INTERCONNECTING WIRING BETWEEN ELECTRONIC EQUIPMENT ALWAYS REMOVE POWER
AND WAIT AT LEAST THIRTY (30) SECONDS BEFORE ANY CONNECTIONS OR
DISCONNECTIONS ARE MADE. FAILURE TO OBSERVE THESE PRECAUTIONS COULD RESULT
IN DAMAGE TO OR DESTRUCTION OF THE EQUIPMENT AND/OR BODILY HARM.

CAUTION

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES.

WARNING

IN ORDER TO USE THE PANTHER PANEL-MOUNT TERMINAL IN AN AREA
CLASSIFIED AS CLASS I, II AND III, DIVISION 2, GROUPS A, B, C, D, F OR
G, METTLER TOLEDO CONTROL DRAWING 155907R MUST BE FOLLOWED
WITHOUT EXCEPTION. FAILURE TO DO SO COULD RESULT IN BODILY
HARM AND/OR PROPERTY DAMAGE.

WARNING

THE PANTHER TERMINAL IS NOT INTRINSICALLY SAFE! DO NOT USE
WITHIN AREAS CLASSIFIED AS HAZARDOUS DIVISION 1 OR ZONE 0/1
BECAUSE OF COMBUSTIBLE OR EXPLOSIVE ATMOSPHERES.

WHEN THIS EQUIPMENT IS INCLUDED AS A COMPONENT PART OF A
SYSTEM, THE RESULTING DESIGN MUST BE REVIEWED BY QUALIFIED
PERSONNEL WHO ARE FAMILIAR WITH THE CONSTRUCTION AND
OEPRATION OF ALL COMPONENTS IN THE SYSTEM AND THE POTENTIAL
HAZARDS INVOLVED. FAILURE TO OBSERVE THIS PRECAUTION COULD
RESULT IN BODILY HARM AND/OR PROPERTY DAMAGE.

WARNING!

WARNING!

IF THIS DEVICE IS USED IN AN AUTOMATIC OR MANUAL FILLING
CYCLE, ALL USERS MUST PROVIDE A HARD-WIRED EMERGENCY STOP
CIRCUIT OUTSIDE THE DEVICE CIRCUITRY. FAILURE TO OBSERVE THIS
PRECAUTION COULD RESULT IN BODILY INJURY AND/OR PROPERTY
DAMAGE.

CONTENTS

1 Introduction ................................................................................................................. 1-1

Overview ..................................................................................................................... 1-1

Standard Features......................................................................................................... 1-2

Optional Features ......................................................................................................... 1-4

Specifications............................................................................................................... 1-5

Standards Compliance ................................................................................................ 1-11

2 PANTHER Terminal Operations ....................................................................................... 2-1

PANTHER Keypad ......................................................................................................... 2-1

Operator Functions........................................................................................................ 2-2

Advanced Operator Functions ........................................................................................ 2-3

3 Basic Service Information.............................................................................................. 3-1

Cleaning and Maintenance ............................................................................................ 3-1

Installation, Programming and Service............................................................................ 3-1

Error Codes.................................................................................................................. 3-2