Mettler Toledo ICS425d-f, ICS425a, ICS425k-LA, ICS425k-f, ICS425k-DR User Manual

...

Download

User manual

ICS425

Weighing terminals

Compact scales

ICS425a ICS425d

ICS425d-...XS/f ICS425k-...XS/f ICS425k-...XS/DR/f

ICS425d-...SM/f ICS425k-...SM/f ICS425k-...SM/DR/f

ICS425d-...LA/f ICS425k-...LA/f ICS425k-...LA/DR/f

Congratulations on choosing the quality and precision of METTLER TOLEDO. Proper use according to these instructions and regular calibration and maintenance by our factorytrained service team ensure dependable and accurate operation to protect your investment. Contact us about a ServiceXXL agreement tailored to your needs and budget.

We invite you to register your product at

www.mt.com/productregistration

so we can contact you about enhancements, updates and important notications concern

ing your METTLER TOLEDO product.

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

Contents

1 Introduction .........................................................................................................4

1.1 Safety instructions ................................................................................................ 4

1.2 Presentation ......................................................................................................... 5

1.3 Commissioning .................................................................................................. 11

2 Operation .......................................................................................................... 15

2.1 Switching on and off .......................................................................................... 15

2.2 Simple weighing ................................................................................................. 15

2.3 Switching units ................................................................................................... 15

2.4 Zeroing / Zero point correction .............................................................................. 16

2.5 Weighing with tare .............................................................................................. 16

2.6 Displaying information ........................................................................................ 18

2.7 Printing results ................................................................................................... 18

2.8 Average (dynamic) weighing ................................................................................ 19

2.9 Working with identications ................................................................................. 19

2.10 Cleaning ............................................................................................................ 20

2.11 Verication test ................................................................................................... 20

3 Settings in the menu .......................................................................................... 21

3.1 Operating the menu ............................................................................................21

3.2 Scale menu block ............................................................................................... 24

3.3 Application menu block ....................................................................................... 28

3.4 Terminal menu block ...........................................................................................29

3.5 Communication menu block ................................................................................33

3.6 Maintenance menu block..................................................................................... 42

4 Event and error messages ..................................................................................44

4.1 Error conditions ..................................................................................................44

4.2 Errors and warnings ............................................................................................45

4.3 Smart weighing counter / spanner icon .................................................................46

4.4 Service information .............................................................................................46

5 Technical data and accessories .......................................................................... 47

5.1 Technical data weighing terminal ......................................................................... 47

5.2 Technical data weighing platforms .......................................................................49

5.3 Dimensional drawings ........................................................................................ 51

5.4 Accessories........................................................................................................ 52

5.5 Assignment of the interface connections ................................................................53

6 Appendix ..........................................................................................................54

6.1 Notice for veried instruments in EC countries ........................................................ 54

6.2 Tables of Geo Code values................................................................................... 54

6.3 Disposal ............................................................................................................ 56

6.4 Protocol printouts ............................................................................................... 57

6.5 Index .................................................................................................................58

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Introduction

1 Introduction

1.1 Safety instructions

General

▲ Do not use the device in a hazardous environment. Special devices are available in

our range of products for hazardous environments.

▲ The safety of the device cannot be ensured if it is not operated in accordance with

these operating instructions.

▲ Only authorised personnel may open the device.

Devices with protection level IP65

Devices with protection level IP65 are dust-tight and protected from water jets according to EN 60529. They are suitable for use in dusty environment and brief contact with liquids.

▲ Ensure that the device is dried off again after coming into contact with liquid. ▲ Do not use the device in environments with a risk of corrosion. ▲ Do not ood the device or submerge it in liquid.

Devices with built-in power supply unit

▲ Ensure that the power socket outlet for the device is earthed and easily accessible, so

that it can be de-energised rapidly in emergencies.

▲ Ensure that the supply voltage at the installation site lies within the range of 100V

to 240V.

▲ Check the power cable regularly for damage. If it is damaged, immediately disconnect

the device from the power supply unit.

Devices with built-in storage battery

▲ Only use storage batteries from the manufacturer. ▲ Do not use the battery charger in humid or dusty rooms or below 0 °C (32 °F)

ambient temperature.

▲ After the storage battery has been charged, the cover cap of the charging socket at the

device must be closed.

Compact scales

▲ Avoid falling loads, shock loads as well as impacts from the side.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

1.2 Presentation

1.2.1 Weighing terminals

There are two versions of the ICS425 weighing terminal: ICS425a with analog scale interface:

to connect analog weighing platforms

ICS425d with digital scale interface SICSpro, which is based on RS422:

to connect METTLER TOLEDO weighing platforms with digital scale interface SICSpro, e.g., PBD 655

1.2.2 Compact scales

A compact scale consists of a weighing terminal with digital scale interface SICSpro and a

weighing platform which are xed together.

Depending on the connected weighing platform there are two basic versions of the ICS425 compact scales:

ICS425d-.../f ICS425 compact scale with strain gauge load cell ICS425k-.../f ICS425 compact scale with MonoBloc® load cell

The weighing platforms are available in three different sizes as shown below.

ICS425d-...XS/f ICS425k-...XS/f

ICS425k-...XS/DR/f

ICS425d-...SM/f

ICS425k-...SM/f

ICS425k-...SM/DR/f

ICS425d-...LA/f ICS425k-...LA/f

ICS425k-...LA/DR /f

extra small weighing platform small weighing platform large weighing platform

Naming

The complete name of a compact scale also indicates the type, size and capacity of the connected weighing platform. E.g., ICS425k-6SM/DR/M/f stands for ICS425k ICS425 terminal, weighing platform with MonoBloc

load cell 6 weighing capacity in kg SM size of the weighing platform DR if present: Delta Range weighing platform

M if present: weighing platform veried by the manufacturer

/f mechanical design: xed connection

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Introduction

1.2.3 Options

Interfaces

ICS425a / ICS425d weighing terminals

• 1 serial interface RS232

• 1 analog scale interface resp. digital scale interface SICSpro

ICS425d.../f / ICS425k.../f compact scales

• 1 serial interface RS232

• 1 digital scale interface SICSpro

An additional communication interface is possible.

• RS232

• RS422/485

• USB Device

• USB Host

• Ethernet

• WLAN

• Digital I/O

Default equipment

Weighing platform resolutions for compact scales

Default Optional

ICS425d-.../f 1 x 6,000 d, non-approved 1 x 30,000 d, non-approved

1 x 60,000 d, non-approved 1 x 6,000 d, approved, e = d

ICS425k-.../f up to 1 x 610,000 d,

non-approved

up to 1 x 61,000 d, approved,

e=10d

Further options

• Exchangeable storage battery (IP54)

• Built-in storage battery (IP65)

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

1.2.4 Display

To meet your special requirements different display layouts are available in the Terminal menu.

Straight weighing display

1 Metrological data – for details see following table 2 Weight value with star, sign and stability monitor – for details see following table 3 Spanner icon: service needed – for details see Event and error messages 4 Battery symbol 5 Net/Gross 6 Unit 7 Bargraph 8 Auxiliary data line – the contents is dened in the menu 9 Symbol and info line – for details see following table

Default layout

Weight values in 3-line mode

Bargraph

The device offers a bargraph indicating the scale capacity available.

The bargraph indicates roughly which part of the scale capacity is already occupied and what capacity is still available. In the example, approx. 3/4 of the scale capacity is occupied, although the applied net weight isn’t really high. The reason therefore could be a high tare weight.

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Introduction

Metrological data line

The metrological data are stored in the weighing platform. The weighing terminal only serves as indicator.

In the metrological data line the following information is displayed:

Symbol Information Remark

, ,

Accuracy classes Displayed only if the scale is approved

according to the Weights and Measures guidelines

, ,

Weighing range information

For multi range devices only, displayed only if the scale is approved according to the Weights and Measures guidelines

Maximum capacity –

Minimum capacity Displayed only if the scale is approved

according to the OIML Weights and Measures guidelines

Approved resolution OIML: Displayed only if the scale is

approved

NTEP: Displayed only if the scale is

approved and d is different from e

Display resolution Please note for approved scales:

OIML: Displayed only if d is different

frome

NTEP: Displayed always

Approved weighing device

Metrology display disabled, Weights and Measures data must be indicated on a label near the weight display

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

Weight value

The weight value can be marked with the following symbols:

Symbol Information Remark

✱

Calculated weight value E.g., for average weighing results

–

Sign For negative weight values

Stability monitor For unstable weight values

1.2343 kg

Non-approved last digit with e > d

For approved scales only The example shows the weight value for a scale with e = 1 g and d = 0.1 g The last, smaller digit is not approved

Symbols and info line

In the symbols and info line the following information can be displayed:

Symbol Information Remark

l<–>l

Weighing range For multi range or multi interval scales only

Scale number –

Weight below minimum weight

MinWeigh must be activated in the menu

Average weighing Average must be activated in the menu

Automatic taring Auto Tare must be activated in the menu

Automatic clearing of the tare weight

A-Clear Tare must be activated in the menu

>0<

Center of zero indication

Availability depending on local Weights and Measures regulations

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Introduction

1.2.5 Function keys

Key Name Function in the operating mode Function in the menu

Power • Switching on and off

• Cancel editing

• Exit menu

Clear • Clear tare

• Leave info page

• Clear value

• To the next higher menu level

(scroll left, )

• In numeric entries: clear digit ()

Switch • Switch over weight unit • Re-edit

• Scroll up ()

• In numeric entries: increment value ()

Zero • Set scale to zero

• Clear tare

• Scroll down ()

• In numeric entries: decrement value ()

Tare • Tare scale

• Clear tare

• Enter menu item (scroll right, )

• In numeric entries: to the next digit to the

right ()

Info • Activate info screen

• Proceed to next info line / info page

• Freeze and release startup screen

–

Transfer • Transfer data to a printer or computer • Conrm entry / selection

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

1.2.6 Connections

1 2 43

1 Power supply or battery charging 2 Standard interface COM1 (RS232) 3 Optional interface COM2 4 Digital weighing platform connection SCALE

The SCALE connection for analog scales is without plug, but with cable exit.

1.3 Commissioning

1.3.1 Selecting the location

The correct location is crucial to the accuracy of the weighing results.

➜ Select a stable, vibration-free and, if possible, a horizontal location for the weighing

platform. The ground must be able to safely bear the weight of the fully loaded weighing platform.

➜ Observe the following environmental conditions:

– No direct sunlight – No strong drafts – No excessive temperature uctuations

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Introduction

1.3.2 Levelling the weighing platform

Only weighing platforms that have been levelled precisely horizontally provide accurate weighing results. Weights and Measures approved weighing platforms have a spirit level to simplify levelling.

➜ Turn the adjustable feet of the weighing platform until the spirit level’s air bubble is

inside the inner circle.

Levelling of compact scales

On compact scales levelling can be done in an easier way.

1. Turn the compact scale upside down.

2. Unscrew the plastic screw in the middle of the terminal front side far enough that it does support the terminal.

3. Screw in the 2 adjustable feet on the side facing the terminal.

4. Turn over the compact scale into its normal position.

5. Level the compact scale by turning the other 2 adjustable feet of the weighing platform until the spirit level's air bubble is inside the inner circle.

1.3.3 Weighing platform connection

Analog weighing platforms

➜ Call the METTLER TOLEDO service technician to connect an analog weighing platform

to the ICS425a weighing terminal.

Weighing platforms with digital scale interface SICSpro

➜ Connect the weighing platform connector to the ICS425d weighing terminal.

• If you have ordered an approved weighing system consisting of an ICS425d weighing terminal and an approved PBD... weighing platform, the approval was done in the factory.

• Due to the new digital scale interface SICSpro, you can disconnect the weighing platform from the weighing terminal of an approved weighing system without violating the approval.

– If another weighing platform is connected to the weighing terminal, the system is

not approved.

– If the weighing platform of the approved system is connected again, the approval

is valid again.

• If you have connected a non-approved weighing platform and want to approve the system, call the METTLER TOLEDO service technician.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

1.3.4 Power supply connection

CAUTION Risk of electric shock!

▲ Before connecting the power supply, check whether the voltage value printed on the

rating plate corresponds to your local system voltage.

▲ Do not under any circumstances connect the device if the voltage value on the rating

plate deviates from the local system voltage.

▲ Make sure the weighing platform has reached room temperature before switching on

the power supply.

➜ Plug the power plug into the power socket.

After it has been connected, the device runs a self-test. The device is ready to operate when zero appears on the display.

1.3.5 Handling of the storage battery

Note the following when operating a device with a built-in storage battery:

• The operating life depends on the intensity of use, the conguration and the connected

scale. For details see the technical data.

• The battery symbol shows the current state of charge of the storage battery. – One segment corresponds with approx. 25 % capacity. – If the symbol ashes, the storage battery has to be charged. – During charging the segments are "running" until the battery is fully charged and

all segments light up continuously.

• The charging time of the storage battery amounts to approx. 6 hours.

The storage battery is protected against overcharging.

• The storage battery has a service life of approx. 2 years or 500 to 1,000 charging/

discharging cycles.

CAUTION No success in charging the storage battery due to low temperatures!

▲ Do not charge the battery if the battery temperature is below 0 °C (32 °F). Charging

is not possible in this temperature range.

▲ Do not operate the battery charger outside its temperature range of 0 °C to 40 °C

(32°F to 104°F).

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Introduction

Recommended use of the storage battery

The characteristics mentioned above are only valid if the following recommendations are observed:

• Change the battery as soon as the warning message "Lowbattery" appears and the battery symbol starts ashing. When the message appeares you still have enough time (at least 10minutes) to complete your current task.

• For optimum battery performance operate the device with built-in storage battery at an

ambient temperature in the range of 10 °C to 30 °C (50 °F to 86 °F). This applies to discharging as well as charging the battery.

• If you plan to put the scale out of operation for a longer period, charge the battery completely.

• Even if you do not use the instrument, charge the battery at least every 3months to

avoid deep discharge.

• On devices with removable battery, remove the battery prior to long term storage.

Changing battery

1. Unlock the battery by moving the slider to the outside and remove the discharged battery.

2. Insert the fully charged battery and secure it by moving the slider to the inside.

With optional IP65 protection, the battery is not accessible from the outside. Please call the METTLER TOLEDO service technician.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

2 Operation

2.1 Switching on and off

2.1.1 Switching on/off

➜ Press .

For a few seconds the device shows a start-up screen with device name, software version, serial number of the weighing terminal and the Geo value (not for MonoBloc

weighing platforms).

• You can freeze the start-up screen by pressing .

• When you start a compact scale, the metrology line shows whether it is approved or not. If you have ordered an approved compact scale, approval has been done in the factory already.

• When user management is active, you are asked to select your name and enter the corresponding password.

➜ Press .

Before the display goes out, -OFF- appears briey.

Switching on

Switching off

2.1.2 Resetting

➜ Press and hold for approx. 5 seconds.

The device is reset and will operate with the last saved settings.

2.2 Simple weighing

1. Place weighing sample on the scale.

2. Wait until the stability monitor goes out.

3. Read the weighing result.

2.3 Switching units

The weight value can be displayed in a second weight unit.

➜ Press .

The weight value is displayed in the second weight unit until the key is pressed again.

When in the Terminal menu Unit roll is set to On, the weight value can be displayed in all available weight units by repeatedly pressing .

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Operation

2.4 Zeroing / Zero point correction

Zeroing corrects the inuence of slight changes on the load plate or minor deviations from

the zero point.

1. Unload scale.

2. Press . Zero appears in the display.

In case of nonveried scales, the automatic zero point correction can be deactivated in the menu or the zero range can be changed. Approved scales are set xed to 0.5 d.

By default, the zero point of the scale is automatically corrected when the scale is unloaded.

• The zero function is only available within a limited weighing range.

• After zeroing the scale, the whole weighing range is still available.

• A successful zeroing will always delete a tare weight.

Manual

Automatic

2.5 Weighing with tare

2.5.1 Taring

➜ Place the empty container on the scale and press .

The zero display and the symbol NET appear. The tare weight remains stored until it is cleared.

2.5.2 Clearing the tare

➜ Press .

The symbol NET goes out, the gross weight appears in the display.

If the symbol is displayed, i.e., the A-Clear Tare function is activated in the menu under Scale -> Tare, the tare weight is automatically cleared as soon as the scale is unloaded.

2.5.3 Automatic clearing of the tare

A tare weight is automatically cleared when the scale is unloaded.

Prerequisite

9 The symbol

is displayed, i.e., the tare function A-Clear Tare is activated in

the Scale menu.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

2.5.4 Automatic taring

If you place a weight on an empty scale, the scale tares automatically and the symbol

NET is displayed.

Prerequisite

9 The symbol

is displayed, i.e., the tare function Auto Tare is activated in the

Scale menu.

The weight to be tared automatically, e.g., packaging material, must be heavier than

9display steps of the scale.

2.5.5 Chain tare

With this function it is possible to tare several times if, e.g., cardboard is placed between individual layers in a container.

Prerequisite

9 The tare function Chain tare is activated in the Scale menu.

1. Place the rst container or packaging material on the scale and press

. The packaging weight is automatically saved as the tare weight, the zero display and the symbol NET appear.

2. Weigh the weighing sample and read/print out the result.

3. Place the second container or packaging material on the scale and press again. The total weight on the scale is saved as the new tare weight. The zero display appears.

4. Weigh the weighing sample in the second container and read/print the result.

5. Repeat steps 3 and 4 for other containers.

2.5.6 Tare preset

If you know the weight of your containers, you can enter the tare weight via barcode or SICS command. Thus you do not have to tare the empty container.

Prerequisite

9 For barcode use Tare preset is selected as destination for external input.

1. Enter the known tare weight via barcode or SICS command. The weight display shows the negative tare weight and the symbol NET appears.

2. Place the full container on the weighing platform. The net weight is displayed.

The entered tare weight is valid until a new tare weight is entered or the tare weight is clared.

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Operation

2.6 Displaying information

Up to 5 different items for display can be congured in the menu for the info key. Depending on the conguration in the Terminal menu, the following data can be assigned in a

free order, e.g.,

• Date & Time

• Weight values

• Identications

• Device information

• Serial numbers and software versions

On the second and third info page, system and contact information can be displayed.

1. Press .

The (rst) info page is displayed.

2. Press again. The next info screen is displayed.

3. To leave the info screens, press .

An info screen is displayed until is pressed again or is pressed.

2.7 Printing results

If a printer or computer is connected, weighing results and other information can be printed or transferred to a computer.

➜ Press .

The dened data is printed or transferred to the computer.

The printout content can be dened in the Templates menu.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

2.8 Average (dynamic) weighing

With the average weighing function, it is possible to weigh restless weighing samples such as living animals. If this function is activated, is displayed in the info line. With average weighing, the scale calculates the mean value from weighing operations within a certain time interval. The time interval for calculation can be set in the Application menu.

9 Application -> Average -> Mode –> Print key (factory setting),

Info key or Switch key is selected in the menu.

9 Weighing sample heavier than 9 scale divisions.

1. Place the weighing sample on the scale.

2. Press the selected key to start average weighing.

3. During average weighing, stars appear in the display, and the average result will be displayed with the symbol ✱.

4. Unload the scale to be able to start a new average weighing operation.

9 Application -> Average -> Mode –> Auto is selected in the menu. 9 Weighing sample heavier than 9 scale divisions.

1. Place the weighing sample on the scale. Average weighing starts automatically. During average weighing, stars appear in the display, and the average result will be displayed with the symbol ✱.

2. Unload the scale to be able to perform a new average weighing operation.

With manual start

(factory setting)

With automatic start

2.9 Workingwithidentications

Weighing series can be assigned 3 identication numbers ID1, ID2 and ID3 with up to 40 characters which are also printed out in the protocols. If, for example, a customer

number and an article number are assigned, it can be clearly seen in the protocol which article was weighed for which customer.

Barcodeuse(foroneidenticationonly)

9 ID1, ID2 or ID3 is selected as destination for external input in the Communication

menu.

9 To display the identication, in the Terminal menu ID1, ID2 or ID3 is

activated for the auxiliary line.

UsingSICScommandset(upto3identications)

9 To display the identication(s), in the Terminal menu ID1, ID2 or ID3 is

activated for the auxiliary line.

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Operation

2.10 Cleaning

Risk of electric shock

▲ Before cleaning, unplug the power plug in order to disconnect the terminal from the

power supply.

▲ Cover open connectors with protective caps.

• Clean the protective cover separately. The protective cover is dishwasher-safe.

• Take off the load plate and remove any dirt and foreign substances which may have

collected underneath. Do not use any hard objects to do so.

• Do not disassemble the weighing device.

• Remove any possibly remaining detergent by rinsing with clear water.

• Observe all the existing regulations on cleaning intervals and permissible cleaning

agents.

Cleaning of other weighing platforms than described in this user manual

➜ Make sure to observe the cleaning instructions for the connected weighing platform.

The weighing platform may not be designed for the environments and cleaning procedures described above.

2.11 Vericationtest

The weighing instrument is veried if

• the accuracy class is displayed in the metrological line,

• the approval readability is shown with "e = readability",

• it bears an ofcial verication mark, e.g., the green M sticker (OIML),

• the validity is not expired.

The weighing instrument is also veried if

• the metrological line shows "Approved scale",

• labels with the metrological data are placed near the weight display,

• the securing seal is not tampered with,

• it bears an ofcial verication mark, e.g., the green M sticker (OIML),

• the validity is not expired.

The period of validity is countryspecic. It is in the responsibility of the owner to renew verication in due time.

Strain gauge weighing platforms

Strain gauge weighing platforms use a Geo Code to compensate gravitational inuence. The manufacturer of the weighing instrument uses a dened Geo Code value for verication.

➜ Check if the Geo Code in the instrument corresponds with the Geo Code value dened

for your location. The Geo Code value is displayed when you switch on the instrument. The Geo Code for your location is shown in the Appendix.

➜ Call the METTLER TOLEDO service technician if the Geo Code values do not match.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

3 Settings in the menu

In the menu, settings can be changed and functions can be activated. This enables adaptation to individual weighing requirements. The menu consists of the following 5 main blocks containing various submenus on several levels.

Scale see section 3.2 Application see section 3.3 Terminal see section 3.4 Communication see section 3.5 Maintenance see section 3.6

3.1 Operating the menu

3.1.1 Calling up the menu and entering the password

The menu differentiates between 2 operating levels: Operator and Supervisor. The Supervisor level can be protected by a password. When the device is delivered, both levels are accessible without a password.

1. Press and keep it pressed until Enter code appears.

2. Press again.

The menu item Terminal is displayed. Only parts of the submenu Device are accessible.

1. Press and keep it pressed until Enter code appears.

2. Enter the password and conrm with

The rst menu item Scale is highlighted.

No supervisor password has been dened when the device is rst delivered. Therefore, conrm the password inquiry with when you call up the menu for the rst time.

If a password has still not been entred after a few seconds, the scale returns to the weighing mode.

Emergency password for Supervisor access to the menu

If a password has been issued for Supervisor access to the menu and you have forgotten it, you can still enter the menu:

➜ Press

3 times and conrm with .

Operator menu

Supervisor menu

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Settings in the menu

3.1.2 Display presentation in the menu

Menu items are displayed together with their context.

1 Menu items; the selected menu item is highlighted 2 Scroll ag, like the scroll bar of your PC 3 Sub-menu items 4 Menu info line, i.e., menu path of the current menu item 5 Navigation info line: use the keys below to navigate the menu as indicated

Exiting the menu

1. Press . "Save settings ?" is displayed.

2. Press OK. The menu changes are saved and the terminal returns to the weighing mode. – or –

➜ Press ESC for further menu settings.

– or –

➜ Press NO to discard changes and return to the weighing mode.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

3.1.3 Selecting and setting parameters in the menu

Example: Sett ing of t he average weighing mode to automatic

1. In the menu start screen use  to select (highlight) the Application menu.

The submenus are displayed in the middle column.

2. Press  to enter the Application menu.

3. Press  and then press  to open the Avg. weighing submenu.

The current setting of the highlighted menu item is displayed in the right column.

4. Press  to enter the Mode submenu.

The possible settings of the selected menu item are displayed on the right side.

5. Press  to select (highlight) Auto and conrm selection with OK.

The setting of the average weighing mode has changed.

If all the settings of a menu item cannot be displayed on one page (e.g., all the info items), just use  to proceed to the hidden items.

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Settings in the menu

3.2 Scale menu block

Factory settings are printed in bold in the following overview.

3.2.1 Overview

After selecting SCALE 1, the following menu is available.

Level 1 Level 2 Level 3 Level 4

Identica-

tion

Scale location

Scale ident.

Linear. &

Calib.

Linearisation

Calibration

Auto print calib.

On, Off

Disp. unit

& res.

Display unit 1

g, kg, oz, lb, lb-oz, t

Display unit 2

g, kg, oz, lb, lb-oz, t

Disp. resolution Off, ...

Unit roll

On, Off

Zero AZM

Off, 0.5d, 1d, 2d, 5d, 10d

Tare Auto tare

On, Off

Chain tare

On, Off

Auto clear tare

On, Off

Restart

On, Off

Filter Vibration

Low, Medium, High

Process

Universal, Dosing

Stability

Fast, Standard, Precise

MinWeigh Function

On, Off

FACT * Temperature Off, 1K, 2K, 3K

Time Time 1, Time 2, Time 3

Days Monday, ... Sunday

Off, On

Reset Perform reset ?

* for MonoBloc

load cells only

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

3.2.2 Scale–>Identication

Scale location

Entering the scale location, e.g., oor and room

Scale ident.

Entering the scale identication, e.g., inventory number

Note • Scale location and scale identication can be displayed in the auxiliary or info lines

or printed out.

• Scale location and scale identication can consist of up to 12 characters (0 ... 9

and decimal point)

3.2.3 Scale –> Linearisation & Calibration

This menu item is not available for veried scales.

Last calibration

Shows the date of the last calibration.

Autoprint calib.

When set to On, a protocol is printed out automatically for each calibration process.

Perform calib.

------ blinking Preload blinking xx kg blinking

1. Unload the scale.

2. Apply preload and conrm with OK.

3. If necessary, change the calibration weight value displayed using

 / .

4. Apply the indicated calibration weight on the weighing platform and conrm with OK.

Passed is displayed briey.

Note In order to achieve a particularly high precision, calibrate under full load. The

calibration process can be aborted using

3.2.4 Scale –> Display units & resolution

Display unit 1

Selecting weighing unit 1

Display unit 2

Selecting weighing unit 2, different from unit 1

Display resolution

Selecting readability (resolution), the possible settings depend on the connected scale. When set to Off, only the default resolution of the weighing platform is available.

Unit roll

When unit roll is switched on, the weight value can be displayed in all available units with

Notes • In case of veried scales, individual subitems of the Display/Units &

Resolution menu item may not be available or only to a limited extent, depending on the respective country.

• On dual-range/dual interval scales, resolutions marked with l<–>l 1/2 are divided

up into 2 weighing ranges/intervals, e.g., 2 x 3000 d.

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Settings in the menu

3.2.5 Scale –> Zero – Automatic zero update

AZM

On veried scales, this menu item does not appear.

Switching on/off automatic zero update and selecting zeroing range.

3.2.6 Scale –> Tare – Tare function

Auto tare

Conguring automatic taring

On, Off

Switching automatic taring on/off When a load is placed on the scale and the gross weight exceeds 9 d, the weight is tared automatically.

Chain tare

Switching on/off chain tare

Auto clear tare

Conguring automatic clearing of the tare weight

On, Off

Switching automatic clearing of the tare weight on/off When the load is removed and the weight drops below 9 d, the tare weight is cleared automatically

3.2.7 Scale –> Restart – Automatic saving of zero point and tare value

Restart

When the Restart function is activated, the last zero point and the tare value are saved. After switching off/on or after a power interruption, the device continues to work with the saved zero point and tare value.

3.2.8 Scale –> Filter – Adaptation of the ambient conditions and the weighing type

Vibration

Adaptation to ambient conditions

Low

• Very steady and stable environment. The scale works very rapidly, but is very sensitive to external inuences.

Medium

• Normal environment. The scale operates at medium speed.

High

• Restless environment. The scale works more slowly, but is insensitive to external inuences.

Process

Adaptation to the weighing process

Universal

• Universal setting for all weighing samples and normal weighing goods.

Dosing

• Dispensing liquid or powdery weighing samples.

Stability

Adjusting the stability detector

Fast

• The scale operates very fast.

Standard

• The scale operates at medium speed.

Precise

• The scale operates with the greatest possible reproducibility.

The slower the scale works, the greater the reproducibility of the weighing results.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

3.2.9 Scale –> MinWeigh – Minimum weight value

Before you can use this function, the METTLER TOLEDO service technician has to determine and enter a minimum weight value.

Function

On/Off

Switching MinWeigh function on/off When set to On and if the weight on the scale drops below the stored minimum

weight,

will appear in the symbols and info line.

3.2.10 Scale –> FACT – automatic temperature-dependent adjustment

This menu item appears only on scales with an internal calibration weight.

Temperature

Setting the temperature difference for automatic adjustment.

Off

Switching off automatic adjustment in the case of a temperature difference.

1K, 2K, 3K

Automatic adjustment in case of the selected temperature change.

Time

Setting up to 3 times per day for the automatic adjustment.

Time 1 ... Time 3

Entering the times for the automatic adjustment (hours, minutes in 24 h format). If you do not want 3 times per day, just set all the times to the same value.

Days

Setting the days of the week for the automatic adjustment.

Monday ... Sunday

On all days which are set to On, the automatic adjustment will be performed.

3.2.11 Scale –> Reset – Resetting scale settings to factory settings

Perform reset ?

Conrmation inquiry

• Reset the scale settings to factory settings with OK.

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Settings in the menu

3.3 Application menu block

Factory settings are printed in bold in the following overview.

3.3.1 Application –> Straight weighing

Printout

Deningprinterandtemplateinthestraightweighingapplication

COM1 ... COM2

Selecting the COM port for the desired printer. E.g., COM1 for printout to a PC and the

optional COM2 for printout on an ofce (ASCII) printer

Off

No printout on this COM port

Standard

Printout with the standard template on the selected printer

Template 1 ...

Template 5

Assigning a customer template to the selected printer

Note Templates can be dened under Communication –> Dene templates

3.3.2 Application –> Average weighing

Mode

Selecting mode for determining the average weight for an unstable load

(dynamicweighing)

Off

Average weighing disabled

Auto

Calculating average weight with automatic start of the weighing cycle

Print key Info key

Switch key

Calculating average weight with manual start of the weighing cycle via the selected key. Print key Info key Switch key

Printout

Deningprinterandtemplateintheaverageweighingapplication

See "Straight weighing"

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

3.4 Terminal menu block

The Terminal menu block consists of the following main subblocks, which are described in detail in the following.

• Device

• Access

Factory settings are printed in bold in the following overview.

3.4.1 Terminal –> Device – General device settings

Overview

Level 1 Level 2 Level 3 Level 4 Level 5

Region Laguage

English, Deutsch, Français, Italiano, Español, Chinese,

...

Date format MM/DD/YY, MM/DD/YYYY, MMM/DD/YYYY, DD/MM/YY, DD/MMM/YYYY,

YY/MM/DD, YYYY/MMM/DD, YYYY/MM/DD, DD/MM/YYYY

Set date Set year

Set month

Set day

Time format

24:MM, 12:MM tt, 24:MM:SS, 12:MM:SS tt

Set time Set hour

Set minutes

Sleep /

Power off

Off, 1 minute, 3 minutes, 5 minutes, 15 minutes, 30 minutes

Identica-

tion

Terminal location

Terminal identication

Display Display

layout

Default, 3-line mode

Contrast

1 ... 10

Brightness

1 ... 10

Weight hold

O s ... 10 s

Auxiliary

line

Not used, Date & Time, Gross, Net, Tare, High resolution (not available for approved scales), ID1, ID2, ID3, Bargraph, Temperature (for scales with MonBloc® load cell only)

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Settings in the menu

Level 1 Level 2 Level 3 Level 4 Level 5

Keyboard Hard keys Power,

Clear,

Switch,

Info,

Transfer

On, Off

Info key Page 1 Item 1

...

Item 5

Not used, Date & Time, Gross,

Net, Tare, ID1, ID2, ID3,

Terminal ID, Terminal location,

Terminal model, Snr Terminal,

Snr. Scale, Firmware Vers., HighRes, Temperature (for scales with MonBloc® load cell only), MinWeigh,

Scale model, Scale location,

Scale ID

Page 2 & 3 Info page 2

Off, System info, Contact info

Info page 3

Off, System info, Contact info

Beeper

On, Off

Timeout Mode

Off, Rental, Screensaver

Days

Description

Region

Countryspecicsett ings

Language

Selecting the language of the operator interface. We will expand the available languages continuously.

Date format

Selecting the date format

Set date

Set year

Entering the year in the selected format

Set month

Entering the month in the selected format

Set day

Entering the day in the selected format

Time format

Selecting the time format

Set time

Set hour

Entering the hour in the selected format

Set minutes

Entering the minutes

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

Sleep (Operator access) Set t ing t he sleep mode

Off

1 minute

...

30 minutes

This menu item only appears on devices in mains operation. When Sleep is activated, the device switches off display and backlighting after the time period set when not in use and gross weight is 0. Display and backlighting are switched on again by pressing a key or if the weight changes.

Power off (Operator access) Setting the power off mode

Off

1 minute

...

30 minutes

This menu item only appears on devices in battery operat ion. When Power off is activated, the device switches itself off automatically after the time period set when not in use. After this, it must be switched on again using

Identication

Sett ingterminalident icationdata

Terminal location

Entering the terminal location, e.g., oor and room

Terminal ident.

Entering the terminal identication, e.g., inventory number

Note • Terminal location and terminal identication can be displayed in the auxiliary or info

lines or printed out.

• Terminal location and terminal identication can consist of up to 12 characters (0...9 and decimal point)

Display

Sett ingt hedisplayaccordingtoyourspecictask

Display Layout

Selecting the presentation of the weight value.

Contrast

(Operator access)

Setting the contrast of the display. This menu item is accessible with Operator access rights.

Brightness

(Operator access)

Setting the brightness of the display. This menu item is accessible with Operator access rights.

Weight hold

Setting how long the weighing result is frozen in the display after the transfer key has been pressed or auto print was generated.

Auxiliary line

Selecting the contents of the auxiliary display line.

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Settings in the menu

Keyboard

Sett ingt hekeyboardaccordingtoyourspecictask

Hard keys

Locking/unlocking keys. Possible keys Power ( ), Clear ( ), Switch ( ), Info ( ),

Transfer( )

Info key

Conguring the items to be displayed using the info key ( )

Page 1

On the rst page of the info key up to 5 information items on the weighing process can be congured.

1. Select item number

2. Assign information

Page 2, Page 3

On pages 2 and 3 system and contact information will be displayed.

In case of a problem, here you will nd your contact data and the system information

the service technician will ask for. System information is set by the manufacturer, contact information is set by your sales representative.

Beeper

When set to On, each keystroke will be conrmed by a short beep.

Time out

Sett ing t he behaviour when no action takes place on the terminal

Mode

Setting the time out mode.

Off

No time out setting.

Rental

The scale can be used for a set time interval, e.g., when the scale is rented for a special event like a fair or a market.

Screensaver

When there is no action on the scale for the set time, the display will show the screensaver.

Days

Entering the number of days the scale will be active in rental mode.

3.4.2 Terminal –> Access – Password for Supervisor menu access

Supervisor

Password for Supervisor menu access

Password

Enter password for Supervisor menu access.

Retype Password

Repeat the password entry.

Note The password can consist of up to 6 characters.

3.4.3 Terminal –> Reset

Perform reset ?

Conrmationinquiry

• Reset the terminal settings to factory settings with OK.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

3.5 Communication menu block

For detailed information on interface protocols and commands refer to the SICS Reference manual.

The Communication menu block consists of the following subblocks:

Overview Showing the interfaces installed COM1 Parameter settings for the standard RS232 interface COM1. COM2 Parameter settings for the optional second interface COM2.

Dene templates Dening templates to be assigned to the application specic

printouts

The interfaces identify themselves. Therefore only those menu settings appear which are relevant for the individual interface. If no optional interface is installed, the COM2 menu will not appear.

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Settings in the menu

3.5.1 Overview of the communication menu blocks for serial interfaces

Possible settings for serial interfaces

COM1 COM2

RS232 RS232 RS422 /

RS485

Ethernet WLAN USB

Device

USB Host

Mode Print

Auto print Continuous (Dialog) *

✔ ✔ ✔ ✔ ✔ ✔ ✔

Dialog * Factory setting

External input

✔ ✔ ✔ ✔ ✔

–

✔

Toledo Cont.-weight Second display Digitol B Digitol G

✔ ✔ ✔ ✔ ✔ ✔ ✔

Printer

✔ ✔ ✔ ✔ ✔

–

✔

External input

✔ ✔ ✔ ✔ ✔

–

✔

Parameter Baud (factory setting) 9600 9600 9600 – – – –

Parity (factory setting) 8 none 8 none 8 none – – – –

Handshake

✔ ✔ ✔

– – – –

Checksum

✔ ✔ ✔ ✔ ✔

–

✔

STX

✔ ✔ ✔ ✔ ✔

– –

RS Type Net Address Load resistor

– –

✔

– – – –

DHCP IP address Subnet mask Gateway

– – –

✔ ✔

– –

TCP settings – – –

✔ ✔

– –

Wireless settings – – – –

✔

– –

* for more information see Reference manual “MT-SICS for ICS4xx / ICS6xx”

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

Overview RS232 menu block (COM1 / COM2)

Level 1 Level 2 Level 3 Level 4

Mode

Print, Auto print, Continuous (Dialog), Dialog, External input,

Toledo Cont.-weight, Second display

Digitol B,

Digitol G

Net

Gross

Tare

On, Off

Printer Type

ASCII printer, Label printer

ACII Format Line format

Multiple, Single, Fixed

Line length

1 ... 24 ... 100

Separator

. , : ; – _ / \ Space

Expanded

On, Off

Add line feed

0 ... 9

External

input

Preamble length

Data length

Postamble length

Termination char. CR, LF, EOT, ...

Destination

Off, Tare preset, ID1 ... ID3

Parameter Baud

300, 600, ... 9600, ... 115200 baud

Parity

7 none, 8 none, 7 odd, 8 odd, 7 even, 8 even

Handshake

Off, Xon - Xoff

Checksum

Off, On

Reset RS232 Perform Reset ?

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Settings in the menu

Overview RS422 / RS485 menu block (COM2)

Level 1 Level 2 Level 3

Mode

see RS232

Printer

External

input

Parameter Baud

300, 600, ... 9600, ...

115200 baud

Parity

7 none, 8 none, 7 odd,

8 odd, 7 even, 8 even

Handshake

Off, Xon - Xoff

RS-Type

RS422, RS485

Net address

0 ... 31

Checksum

Off, On

Load resistor

Off, On

Reset RS4xx Perform Reset ?

Overview Ethernet menu block (COM2)

Level 1 Level 2 Level 3

Mode

see RS232

Printer

External

input

Parameter DHCP

Off, On

Local IP

Subnet mask

Gateway

Checksum

Off, On

TCP Mode TCP Mode

Server, Client, Both

Local Port

Remote IP

Remote Port

Connect Timeout

Disconnect Timeout

Reset

Ethernet

Perform Reset ?

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

Overview WLAN menu block (COM2)

Level 1 Level 2 Level 3

Mode

see RS232

Printer

External

input

Parameter

see Ethernet

TCP Mode

see Ethernet

Wireless

setting

SSID

Enter SSID

Encryption Off, WEP, WPA

WEP settings 64 Bit, 128 Bit

WEP key Key 1, Key 2, Key 3, Key 4

WPA settings WPA-TKIP, WPA2-AES

Password

Enter password

Status

Display the current status, e.g., connection status, signal strength.

Reset WLAN Perform Reset ?

Overview USB Device and USB Host menu blocks (COM2)

Level 1 Level 2 Level 3 Level 4

Mode

Continuous (Dialog), Dialog,

External input *, Toledo Cont.-weight,

Second display

Digitol B,

Digitol G

Net

Gross

Tare

On, Off

Printer *

see RS232

External

input *

Parameter * Checksum

Off, On

Reset USB Perform Reset ?

* USB Host only

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Settings in the menu

3.5.2 Description of the communication menu blocks for serial interfaces

Communication –> COMx –> Mode – Operating mode of the serial interface

Manual data output to the printer with

Auto print

Automatic output of stable results to the printer (e.g., for series weighing operations).

Continuous (Dialog)

Ongoing output of all weight values via the interface.

Dialog

Bi-directional communication via MT-SICS commands, control of the device via PC.

External input

Input other than via terminal keypad. What the input is used for is dened in the

Destination menu block.

Toledo Cont.-weight

TOLEDO Continuous mode

Second Display

On the selected interface port a second display is installed

Digitol B Digitol G

DigiTOLcompatible format, gross weight identied by "B" DigiTOLcompatible format, gross weight identied by "G"

Net, Gross, Tare

Selecting the weight value to be transferred

Note Printing conditions for Auto print and Demand m auto:

• The weight must be heavier than 9 display increments.

• A weight change of at least 9 display increments is required to initiate the next

printout

Communication –> COMx –> Printer – Settings for protocol printout

Type

Selecting printer type

ASCII printer

Label printer

Note

If Label printer is selected, the transmitted data does not include the name of the variable, e.g., date, gross, ID1, but the value and, if apropriate, the unit as a separate

line. This allows the label printer to ll its template with the required data.

ASCII Format

Selecting formats for the protocol printout

Line format

Selecting line format:

Multiple

Mutiple lines

Single

Single line

Fixed

Fixed (Records output in single lines; every record includes the number of characters

that was dened under Line length)

Line length

Setting line length This item is only displayed for the line formats Multiple and Fixed

Separator

Selecting the separator This item is only displayed for the line format Single

Add line feed

Adding line feeds

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

Communication–>COMx–>Externalinput–Conguringbarcodeinput

Preamble length

The barcode may contain additional data ahead of the relevant data (preamble) and behind (postamble).

➜ Enter the number of characters of preamble, (relevant) data and postamble

Data length

Postamble length

Termination char.

Selecting the termination character which is used by the connected barcode scanner

Destination

Selecting the item to be entered via barcode scanner

Communication –> COMx –> Parameter – Communication parameters

Not all parameters are available on all serial interfaces. Refer to the overviews of the interfaces to check which parameters are available.

Baud

Selecting baud rate

Parity

Selecting parity

Handshake

Selecting handshake

Checksum

Activating/deactivating checksum byte

STX

Activating/deactivating STX If STX is enabled, the STX signal (0x02) is sent at the beginning of each output string that is sent via the interface.

RS Type

Selecting type of the optional RS422/RS485 interface

Net Address

Assigning network address

Load resistor

To avoid reexions on a network, we recommend to make a dened termination. For

this purpose the load resistor within the terminal can be used. When set to "On", a resistor of approx. 100 W between the signal lines is enabled

DHCP

If DHCP is set to "On", the device will receive the IP address automatically. Then IP

address, Subnet mask and Gateway are readonly elds

Local IP

Displaying/entering the local IP address

Subnet mask

Displaying/entering subnet mask

Gateway

Displaying/entering gateway address

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Settings in the menu

Communication –> COM2 –> TCP Mode – Transmission control protocol settings

TCP Mode

Server

ICS425 acting as server

Client

ICS425 acting as client

Both

ICS425 acting as both, server or client

Local Port

Displaying/entering the local port

Remote IP

Displaying/entering the remote IP address

Remote Port

Displaying/entering the remote port

Connect timeout

Setting timeout for connecting

Disconnect timeout

Setting timeout for disconnecting

3.5.3 Communication –> Digital I/O (COM2)

Level 1 Level 2 Level 3

Input Input pin 1 ... Input pin 4 Off, Zero, Tare, Transfer,

Switch, Clear, Info, Start

Output Ready, Stable, Tare, Zero,

< Min weigh, >= Min weigh,

Underload, Overload, <= Setpoint 1,

> Setpoint 1, <= Setpoint 2,

> Setpoint 2, Star

Off,

Output pin 1 ... Output pin 4

Setpoints Setpoint 1, Setpoint 2

Output mode Continuous, Stable

Conguringinputs

1. Select an input pin.

2. Assign an input signal to the selected input pin.

Conguringoutputs

1. Select an output signal.

2. Assign an output pin.

Conguringsetpoints

➜ Enter values for the setpoints.

Sett ing output mode

Continuous Digital outputs are updated continuously Stable Digital outputs are updated only when the weight is stable

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

3.5.4 Communication–>Denetemplates

Level 1 Level 2 Level 3

Template 1

...

Template 5

Line 1

...

Line 30

Not used, Header *, Date, Time, Gross, Net, Tare,

High resolution, ID1 ... ID3 *, Terminal ID,

Terminal location, SNR Terminal, SNR Scale, Star line,

New line, Form feed, Weight position

* The content of these items has to be entered via SICS command.

Conguringtemplates

1. Select a template.

2. Select a line.

3. Assign an item.

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Settings in the menu

3.6 Maintenance menu block

3.6.1 Overview

Level 1 Level 2 Level 3 Level 4

Scale test Scale Internal test Perform test?

External test Perform test?

Conf. ext. test Test weight

Weight name

Tolerance

Auto print

On, Off

Keyboard test Perform test?

Display test Perform test?

Serial No. SNR scale

SNR terminal

Print setup Print menu settings?

Reset all Perform reset?

3.6.2 Description

Scale test

Testing the scale

Internal test

For scales with an internal test weight

Perform test?

➜ Press OK to start the test

The deviation of test weight value and actually weighed value is displayed.

External test

For scales without an internal test weight

Perform test?

1. Press OK to start the test Preload is displayed.

2. If applicable, load the preload, and press OK. The test weight is blinking.

3. Load the requested test weight and press OK. The deviation of test weight value and actually weighed value is displayed.

Conf. ext. test

Conguring the external test weight

Test weight

Setting the test weight value

Weight name

Entering the test weight name

Tolerance

Setting the test tolerance

Auto print

When set to On, a protocol is printed for each scale test.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

Keyboard test

Testing the keyboard

Perform test?

1. Press OK to start the keyboard test.

2. Press the keys in the displayed order. If the key works, the device switches to the next key. The keyboard test is terminated by pressing

Display test

Testing the display

Perform test?

1. Press OK to start the display test. A checkerboard pattern is displayed.

2. Press any key to invert the checkerboard pattern.

3. Press

to leave the display test.

The display is working properly if the black and white elds are displayed without

missing pixels.

Serial number

Displaying serial numbers

SNo. scale

Displaying the serial number of the connected weighing platform.

SNo. terminal

Displaying the serial number of the weighing terminal.

Print Setup

Printout of a list of all menu sett ings

Print menu settings

➜ Press OK to start the printout.

Reset All

Reset all sett ings to factory set t ings

Perform reset ?

Conrmation inquiry

• Reset all settings to factory settings with OK.

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Event and error messages

4 Event and error messages

4.1 Error conditions

Error Cause Remedy

Display dark • Backlighting set too dark ➜ Set backlighting brighter.

• No mains voltage ➜ Check mains.

• Unit switched off ➜ Switch on unit.

• Mains cable not plugged in ➜ Plug in mains cable.

• Brief fault ➜ Switch device off and on again.

Weight display unstable • Restless installation location ➜ Adjust vibration adapter.

• Draft ➜ Avoid draft.

• Restless weighing sample ➜ Dynamic weighing.

• Contact between weighing pan and/or

weighing sample and surroundings

➜ Remedy contact.

• Mains fault ➜ Check mains.

Incorrect weight display • Incorrect zeroing ➜ Unload scale, set to zero and repeat

weighing operation.

• Incorrect tare value ➜ Clear tare.

• Contact between weighing pan and/or

weighing sample and surroundings

➜ Remedy contact.

• Weighing platform tilted ➜ Level weighing platform.

• Load plate not on the scale

• Weighing range not reached

➜ Place load plate on the scale. ➜ Set to zero.

• Weighing range exceeded ➜ Unload scale. ➜ Reduce preload.

• Result not yet stable ➜ If necessary, adjust vibration adapter.

"Attention: Approval invalid" alternating with metrological data

• Approval was tampered with ➜ Call METTLER TOLEDO service

technician.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

4.2 Errors and warnings

4.2.1 Error messages

Error messages contain the following information:

Overload !

Error message

Remove load from

load plate

Remedy

Press 'C' key to conrm SW01

Message identier

How to clear the message

4.2.2 Warnings

Warnings are displayed briey and then disappear automatically.

Example

Data not valid

Warning

22013958A

Additional information, e.g., which data is not valid

EI01

Warning identier

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Event and error messages

4.3 Smart weighing counter / spanner icon

This weighing instrument features several control functions to monitor the condition of the device. The METTLER TOLEDO service technician can setup and enable these functions. This helps the user and the METTLER TOLEDO service technician to detemine how the device is treated and what measures are needed to keep it in a good shape. If the control functions triggers an alert, a message is shown.

You can conrm the message and continue to work with the weighing instrument. The

spanner icon lights up.

Service required

Overload problem

Press 'C' key to conrm SW14

In case of an alert we strongly recommend calling the METTLER TOLEDO service technician

• to replace parts which are at the end of lifetime,

• to correct wrong settings,

• to educate operators about proper handling,

• to perform routine service work,

• to reset the alert.

The control functions monitor the following conditions:

• number of weighings

• number of overloads

• maximum weight

• zero commands and zero failures

• battery charging cycles

• power-on time

• date for the next service inspection

4.4 Service information

In case you need the METTLER TOLEDO service technician, you can read the necessary system and contact information from the device.

1. Press twice. System information data are displayed.

2. Press again. Your contact data are displayed.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

5 Technical data and accessories

5.1 Technical data weighing terminal

Housing • Aluminium diecast

Display • LCD liquid crystal graphical display, with backlighting

Keyboard • Tactile-touch membrane keypad (PET)

• Scratch-resistant labelling

Protection type • With power supply connection IP65

• With built-in storage battery IP65

• With exchangeable battery IP54

• Weighing platform IP54 / IP65 (option, not for XS)

Net weight • Weighing terminal 2.0 kg / 4.4 lb

Mains connection

• Direct connection to power supply (supply voltage uctuation not

exceeding ±10 % of the rated voltage)

• Rated voltage 100 ... 240 VAC / 50 ... 60 Hz / 300 mA

• Power cord approx. 2.5 m / 8.2 ft

Storage battery operation

• Supply of device: 12 V

/ 2.5 A

• If the supply voltage is interrupted, the device automatically switches over to storage battery operation

9-28 VDC

powersupply

• Rated voltage: 9 ... 28 V

/ max. 2.5 A

• Power cord approx. 5 m / 16 ft, open ends

Battery charger • Ambient conditions: 0 ... 40 °C / 32 ... 104 °F, dry environment

Ambient conditions

• Application indoor use only

• Altitude up to 2,000 m

• Temperature range Class III –10 ... 40 °C / 14 ... 104 °F

• Temperature range Class II 10 ... 30 °C / 50 ... 86 °F

• Overvoltage category II

• Pollution degree 2

• Humidity: Max. rel. humidity 85 % for temperatures up to 40 °C

Interfaces • 1 interface RS232 and 1 scale interface integrated

• 1 additional optional communication interface possible

W & M approvals

• OIML Class II, III, IIII

• NTEP Class II, III

Applications

• Weighing

• Average weighing

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Technical data and accessories

Operating life with storage battery

The operating life during storage battery operation varies depending on the intensity of use,

the conguration and the connected scale.

The following approximate values apply with standard RS232 interface and the brightness set to 5.

Weighing platform Conditions Duration

With strain gauge weighing platform, e.g., ICS425a-...SM/f

WLAN, continuous operation 8 h

USB host, continuous operation 13 h

With MonoBloc

weighing

platform, e.g., ICS425k-...SM/f

WLAN, continuous operation 7 h

USB host, continuous operation 11 h

Analog scale interface

Impedance • ≥ 80 W

Excitation • 3.3 V

Sensitivity • 2 to 3 mV/V

Max. resolution • 7500 e (OIML

• 300,000 d (non approvable)

Min. verication interval • 0.5 mV/e

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

5.2 Technical data weighing platforms

5.2.1 Strain gauge weighing platforms

ICS425d-.../f compact scales use a weighing platform with strain gauge load cell.

• Approved resolution of 1 x 6,000 e (OIML, NTEP)

• Non-approved resolutions up to 60,000 d

ICS425d-.../f 3SM 6SM 15LA 35LA

Capacity 3 kg 6 kg 15 kg 35 kg

6 lb 12 lb 30 lb 70 lb

Readability

Standard resolution: 6,000 d 0.5 g 1 g 2 g 5 g

0.001lb 0.002 lb 0.005 lb 0.01 lb

Optional resolution: 30,000 d 0.1 g 0.2 g 0.5 g 1 g

0.0002lb 0.0005lb 0.001lb 0.002 lb

Optional resolution: 60,000 d 0.05 g 0.1 g 0.2 g 0.5 g

0.0001 lb 0.0002lb 0.0005lb 0.001lb

Approved resolution: 6,000 e 0.5 g 1 g 2 g 5 g e

0.001lb 0.002 lb 0.005 lb 0.01 lb

Repeatability (sd) 0.05 g 0.1 g 0.2 g 0.5 g

0.0001lb 0.0002lb 0.0005lb 0.001lb

Linearity 0.1 g 0.2 g 0.5 g 1 g

0.0002lb 0.0005lb 0.001lb 0.002lb

Weight 5.5 kg 5.5 kg 7.7 kg 7.7 kg

12.1 lb 12.1 lb 17.0 lb 17.0 lb

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Technical data and accessories

5.2.2 MonoBloc® weighing platforms

ICS425k-.../f and ICS425k-.../DR/f compact scales use a weighing platform with

MonoBloc® load cell.

• Approved resolution of up to 61,000 e (OIML, NTEP)

• Non-approved resolutions up to 610,000 d

• FACT function (Fully Automatic Calibration Technology) calibrates the scale according

to temperature changes thus increasing weighing accuracy

• ICS425k-.../DR/f provide a range with higher resolution.

ICS425k-.../f 0.6XS 3XS 6XS 6SM 15LA7 35LA

Capacity 0.6 kg 3 kg 6 kg 6 kg 15 kg 35 kg

1.2 lb 6 lb 12 lb 12 lb 30 lb 70 lb

Readability

Standard resolution 0.001 g 0.01 g 0.01 g 0.1 g 0.1 g 0.1 g

0.000002lb 0.00002 lb 0.00002 lb 0.0002 lb 0.0002 lb 0.0002 lb

Approved resolution 0.01 g 0.1 g 0.1 g 1 g 1 g 1 g

0.00002lb 0.0002 lb 0.0002 lb 0.002 lb 0.002 lb 0.002 lb

Repeatability (sd) 0.001 g 0.01 g 0.01 g 0.1 g 0.1 g 0.1 g

0.00002 lb 0.00002 lb 0.00002 lb 0.0002 lb 0.0002 lb 0.0002 lb

Linearity 0.002 g 0.02 g 0.02 g 0.2 g 0.2 g 0.3 g

0.000005 lb 0.00005lb 0.00005lb 0.0005lb 0.0005lb 0.0005lb

Weight 5.7 kg 5.7 kg 5.7 kg 5.7 kg 9.0 kg 9.0 kg

12.6 lb 12.6 lb 12.6 lb 12.6 lb 19.8 lb 19.8 lb

ICS425k-.../DR/f 0.6XS 3XS 6XS 6SM 15LA 35LA

Capacity 0.12 kg / 0.6 kg 0.6 kg / 3 kg 1.2 kg / 6 kg 1.2 kg / 6 kg 3 kg / 15 kg 7 kg / 35 kg

Readability

Standard resolution 0.001 g / 0.01 g 0.01 g / 0.1 g 0.01 g / 0.1 g 0.1 g / 1 g 0.1 g / 1 g 0.1 g / 1 g

Approved resolution 0.01 g / 0.1 g 0.1 g / 1 g 0.1 g / 1 g 1 g / 10 g 1 g / 10 g 1 g / 10 g

Repeatability (sd) 0.001 g 0.01 g 0.01 g 0.1 g 0.1 g 0.1 g

Linearity 0.002 g 0.02 g 0.02 g 0.2 g 0.2 g 0.3 g

Weight 5.7 kg 5.7 kg 5.7 kg 5.7 kg 9.0 kg 9.0 kg

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

5.3 Dimensional drawings

5.3.1 Weighing terminal

248 mm / 9.8" 164 mm / 6.5"

33 mm / 1.3"

78 mm / 3.1"

5.3.2 Compact scales

Compact scale with XS or SM weighing platform

364 mm / 14.3"

247 mm / 9.7"

160 mm / 6.3"

95 - 105 mm

/ 3.7" - 4.1"

130 mm / 5.1"

206 mm / 8.1"

Compact scale with LA weighing platform

404 mm / 15.9" 514 mm / 20.2"

357 mm / 14.1"

110 - 120 mm

/ 4.3" - 4.7

110 - 120 mm

/ 4.3" - 4.7

247 mm / 9.7"

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Technical data and accessories

5.4 Accessories

Accessories Order no.

Printer RS-P25/02 Printer USB-P25/02 Printer RS-P26/02 Printer RS-P28/02

11 124 310 11 124 311 11 124 313 11 124 314

Protective cover for the weighing terminal, set of 5 pieces 30 032 638

Auxiliary display AD-RS-M7 12 122 381

Power supply 9-28 V (conversion kit) 22 023 504

Charging station 30 035 339

Battery pack 30 032 647

Windshield for ...XS weighing platforms 72 262 929

Wall bracket 30 032 637

Support for wheeled bench stand 22 023 460

Column for PBA330, PBA655, PBD655 (requires wall bracket 30 032 637) Height 330 mm / 13 ft Height 660 mm / 26 ft

72 198 699 72 198 700

Floor stand, height 1000 mm / 3,3 ft Painted steel Stainless steel

22 023 451 22 023 503

Relaybox 4, for Digital I/O 22 011 967

Power supply for Relaybox 4 00 505 544

Cables Order no.

Cable M12 USB Female Type A, USB host

0.2 m / 0.7 ft, 3 m / 10 ft

22 017 604 22 017 608

Cable M12 USB Male Type A, USB device, 3 m / 10 ft 22 018 967

Cable M12 RS232 Female Sub D 9 pin (crossed; used for PC) 22 017 601

Cable M12 RS232 Male Sub D 9 pin (not crossed; used for SICS scale) 22 017 602

Cable M12 RS422/485, open ends 22 017 603

Cable M12 Digital I/O, open ends 22 018 969

Cable M12 Ethernet RJ45 5 m / 16 ft, 20 m / 66 ft

22 017 610 22 017 614

Cable for auxiliary display AD-RS-M7 30 041 060

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

5.5 Assignment of the interface connections

Digital I/O RS232 RS422 RS485 USB Device

USB Host

Ethernet Power

Socket

Pin 1 In 0 CTS TxD+ T/RxD+ +5 V TD+ +12 V

Pin 2 In 1 TxD TxD– T/RxD– D– RD+ +12 V

Pin 3 In 2 RTS RxD+ – GND TD– GND

Pin 4 In 3 RxD +12 V +12 V D+ RD– GND

Pin 5 In_GND +12 V GND GND

Pin 6 Out 0 +5 V RxD– –

Pin 7 Out 1 –

Pin 8 Out 2 GND

Pin 9 Out 3

Pin 10 Out_GND

Pin 11 +12 V

Pin 12 GND

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Appendix

6 Appendix

6.1 NoticeforveriedinstrumentsinECcountries

Weighing instruments veried at the place of manufacture bear the preceding mark on the

packing label and a green "M" sticker on the descriptive plate. They may be set to work immediately.

Weighing instruments which are veried in two steps have no green "M" on the descriptive plate and bear the preceding identication mark on the packing label. The second step of the verication must be carried out by the approved METTLER TOLEDO service or Weights and Measures authorities. Please contact your METTLER TOLEDO organisation. The rst step of the verication has been carried out at the manufacturing plant. If national regulations in individual countries limit the period of validity of the verication, the operator of such a weighing instrument is himself responsible for its timely reverication.



6.2 Tables of Geo Code values

For weighing instruments veried at the manufacturer’s, the Geo Code value indicates the country or geographical zone for which the instrument is veried. The Geo Code value set in the instrument (e.g.,"Geo 18") appears briey after switching on.

Table "Geo Code values 3000e" shows the Geo Code values for European countries. Table "Geo Code values 6000e/7500e" shows the Geo Code values for different gravitation zones.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

6.2.1 Geo Code values 3000e, OIML Class III (European Countries)

Country Geographical latitude Geo Code value Country Geographical latitude Geo Code value

Austria 46°22’ – 49°01’ 18 Liechtenstein 47°03’ – 47°14’ 18

Belgium 49°30’ – 51°30’ 21 Lithuania 53°54’ – 56°24’ 22

Bulgaria 41°41’ – 44°13’ 16 Luxemburg 49°27’ – 50°11’ 20

Croatia 42°24’ – 46°32’ 18 Netherlands 50°46’ – 53°32’ 21

Czechia 48°34’ – 51°03’ 20 Norway 57°57’ – 64°00’ 24*

Denmark 54°34’ – 57°45’ 23 64°00’ – 71°11’ 26

Estonia 57°30’ – 59°40’ 24 Poland 49°00’ – 54°30’ 21

Finland 59°48’ – 64°00’ 25* Portugal 36°58’ – 42°10’ 15

64°00’ – 70°05’ 26 Romania 43°37’ – 48°15’ 18

France 41°20’ – 45°00’ 17 Slovakia 47°44’ – 49°46’ 19

45°00’ – 51°00’ 19* Slovenia 45°26’ – 46°35’ 18

Germany 47°00’ – 55°00’ 20 Spain 36°00’ – 43°47’ 15

Greece 34°48’ – 41°45’ 15 Sweden 55°20’ – 62°00’ 24*

Hungary 45°45’ – 48°35’ 19 62°00’ – 69°04’ 26

Iceland 63°17’ – 67°09’ 26 Switzerland 45°49’ – 47°49’ 18

Ireland 51°05’ – 55°05’ 22 Turkey 35°51’ – 42°06’ 16

Italy 35°47’ – 47°05’ 17 United Kingdom 49°00’ – 55°00’ 21*

Latvia 55°30’ – 58°04’ 23 55°00’ – 62°00’ 23

* factory setting

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Appendix

6.2.2 Geo Code values 6000e/75000e OIML Class III (Height ≤ 1000 m)

Geographical latitude Geo Code value Geographical lat itude Geo Code value

00°00’ – 12°44’ 18 43°26’ – 47°51’ 18

05°46’ – 17°10’ 21 45°38' – 50°06' 22

12°44’ – 20°45’ 16 47°51’ – 52°22’ 20

17°10’ – 23°54’ 18 50°06’ – 54°41’ 21

20°45’ – 26°45’ 20 52°22’ – 57°04’ 24*, 26

23°54’ – 29°25’ 23 54°41’ – 59°32’ 21

26°45’ – 31°56’ 24 57°04’ – 62°09’ 15

29°25’ – 34°21’ 25*, 26 59°32’ – 64°55’ 18

31°56’ – 36°41’ 17, 19* 62°09’ – 67°57’ 19

34°21’ – 38°58’ 20 64°55’ – 71°21’ 18

36°41’ – 41°12’ 15 67°57’ – 75°24’ 15

38°58’ – 43°26’ 19 71°21’ – 80°56’ 24*, 26

41°12’ – 45°38’ 26 75°24’ – 90°00’ 18

* factory setting

6.3 Disposal

In conformance with the European Directive 2002/96 EC on Waste Electrical and Electronic Equipment (WEEE), this device may not be disposed of with domestic waste. This also

applies to countries outside the EU, according to their specic requirements.

Please dispose of this product in accordance with local regulations at the collecting point

specied for electrical and electronic equipment.

If you have any questions, please contact the responsible authority or the distributor from which you purchased this device. Should this device be passed on to other parties (for private or professional use), the content of this regulation must also be related. Thank you for your contribution to environmental protection.

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

6.4 Protocol printouts

P25 printouts, in English

Straight weighing – standard template Averageweighingwithheaderandidenticationdata

Gross/net/tare weights

Starline

Header

Date/time

Identications

Average weighing result

METTLER TOL EDO User manual ICS425

04/12Order number 22023391A

Appendix

6.5 Index

Accessories .......................... 52

Auxiliary line ........................... 7

Average weighing ................ , 19

Battery

Changing ......................... 14

Handling .......................... 13

Specication ..................... 47

Commissioning .................... 11

Compact scales ...................... 5

Dimensions .......................... 51

Display

Auxiliary line .................... 31

Metrological data ................ 8

Symbols and info line .......... 9

Weight display .................... 9

Disposal .............................. 56

Dynamic weighing .......... 19, 28

Environment ......................... 47

Errors .................................. 44

Error conditions ................ 44

Error messages ................ 45

External input ........... 17, 19, 39

Geo value .......................... , 20

Identications ......... , 31, 19, 35

Info key .......................... 10, 18

Interface settings

Digital I/O ........................ 40

Ethernet ........................... 36

RS232 ............................. 35

RS422 / RS485 ................ 36

USB ................................. 37

WLAN .............................. 37

Keyboard ....................... 10, 30

Application ....................... 28

Communication ................ 33

Operation ......................... 21

Password ........................ 21

Scale ............................... 24

Terminal .......................... 29

Messages ............................ 44

MinWeigh ........................ 9, 27

Mode

Dialog mode .................... 38

Digitol ............................. 38

External input ................... 38

Print mode ....................... 38

Second Display ................ 38

Toledo Continuous ............ 38

Power supply ................. 13, 47

Printing ................................ 18

Printout examples ................. 57

Safety instructions ............. 4, 20

Service information ............. , 18

SICS

Command set ................... 33

Identications ................... 19

Tare preset ....................... 17

Simple weighing ................... 15

Smart weighing counter ......... 46

Spanner icon .................... 7, 46

Switching on and off .............. 15

Tare

Automatic clearing ............ 16

Automatic taring ......... 17, 26

Chain tare ........................ 17

Tare preset ....................... 17

Taring .............................. 16

Templates ...................... 28, 41

Test

Display ............................ 43

Keyboard ......................... 43

Scale ............................... 42

Verication ....................... 20

Veried instruments in EC

countries .............................. 54

Warnings ............................. 45

Zero

Automatic zero update ....... 26

Zeroing ............................ 16

Zero point correction .......... 16

METTLER TOL EDO User manual ICS42504/12 Order number 22023391A

For more information

www.mt.com/service

Mettler-Toledo (Albstadt) GmbH

D-72458 Albstadt Tel. + 49 7431-14 0 Fax + 49 7431-14 232

To protect your METTLER TOLEDO product’s future:

METTLER TOLEDO Service XXL assures the quality, measuring accuracy and preservation of value of all METTLER TOLEDO products for years to come.

Please send for full details about our attractive terms of service. Thank you.

*22023391A*

* 2 2 0 2 3 3 9 1 A *

Mettler Toledo ICS425d-f, ICS425a, ICS425k-LA, ICS425k-f, ICS425k-DR User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual