Mettler Toledo HG63 Operating Instructions Manual

Short-form operating instructions

Menu





















HG63 Moisture Analyzer

For detailled information see operating instructions

Moisture determination (chronological sequence of the measurement cycle and status display “User Guide”)

1 234567

Swtich on

Standby mode Load pan Tare Weigh in Start Drying

Read result

On/Off

2

Enter drying temperature

(standard and rapid drying)

125

130

Enter drying time

‹30

Reset

Return to standby mode
at any time with «Reset»

Numeric entries

or:

0...9

125

Alphanumeric entries

Code

0...9

1

#

95

Start

Heating module adjustment

∑CAˆ NO

†CAˆ NO

†CAˆ YES

wait ....

ENfl [37

Balance adjustments

Menu

∑CAˆ NO

∑CAˆ YES

∑CAˆ

5≠000

%

g

⁄00

Select method

Select method:

Method

Function keys

Selection of the switch-off criterion

Automatic switch-off

1: Quick drying sample
5: Slow drying sample

Manual switch-off with
the «Stop» key

Free switch-off one free switch­off criterion for each method

01

07

0...9

Timed switch-off

Test measurement

with record printout

2

2A

MARGARINE

Selection of the display mode

%

Moisture content

Dry content

Current sample
weight in grams

wait

Start

Read off 1st temperature on temperature ad­justment set and enter:

Read off 2nd temperature on temperature
adjustment set and enter:

†CAˆ 158

○ ○○○○

†CAˆ 102

wait

○○○○○○○

ATRO moisture content

ATRO dry content

∑CAˆ

Selection of the drying program

Standard drying

Rapid drying

≠000

g

© Mettler-Toledo GmbH 2003 11780547 Printed in Switzerland 0310/7.12

Mettler-Toledo GmbH, Laboratory & Weighing Technologies, CH-8606 Greifensee, Switzerland
Phone [phone], Fax [phone], Internet: http://www.mt.com

P11780547

Technische Änderungen und Änderungen im

Lieferumfang des Zubehörs vorbehalten.

Error messages

ERROÈ 1

ERROÈ 2

ERROÈ 3

ERROÈ 4

ERROÈ 5

ERROÈ 6

ERROÈ 7

ERROÈ 8

ERROÈ 9

ERROÈ 10

Important: You must acknowledge the error messages with the «Reset» key before you can continue working with the
instrument. Consult the operating instructions of your instrument for information on other error messages.

Cause: No stability during taring or adjustment
Remedy: Seek stable surroundings/optimum location/Take care that no part

of the sample or the sample pan touch the draft shield element or the
sample pan holder

Cause: No or wrong adjustment weight loaded
Remedy: Load correct adjustment weight

Cause: Loaded sample weight too low
Remedy: Weigh in sample with minimum weight (100 mg)

Cause: Sample vessel has not been tared
Remedy: Tare sample vessel

Cause: Upper/lower limit of admissible input range violated
Remedy: Enter value in admissible range

Cause: Keypad has been locked in menu, printer deactivated in menu
Remedy: Cancel keypad locking, activate printer in menu

Cause: The selected switch-off criterion does not permit a time entry
Remedy: Select switch-off criterion “Timed switch-off”

Cause: Time limit for value entry in heating module adjustment exceeded

(10 minutes)

Remedy: Repeat heating module adjustment and enter value in good time

Cause: Undefined condition
Remedy: Press «Reset» or switch instrument off then on again with «On/Off»

key.

Cause: Sample chamber has not cooled down sufficiently
Remedy: Allow the instrument to cool down to the starting temperature

Record printout (example)

A -MOISTURE DETERMINATION-

B METTLER TOLEDO

Halogen MoistureAnalyzer

C Type: HG63
D SNR: 1234567890
E SW: 2.01

F Method:

05

G QUALITY CHECK
H Switchoff mode 2
I Gentle drying
J Drying temp. 105 °C
K Disp.mode 0...-100 %MC
L Start weight 2.507 g

001:00 min -2.51 %MC

M

002:00 min -3.39 %MC
003:00 min -3.71 %MC

N Total time 3:19 min
O Dry weight 2.412 g
P End result -3.79 %MC

Q ----30.06.03---15.14----

A Record title
B Manufacturer and Designation of the

instrument

C Type of the instrument
D Serial number of the instrument
E Version number of the software
F Selected method number
G Comment line
H Selected switch-off criterion
I Selected drying program
J Drying temperature (set temperature)
K Selected display mode
L Sample weight at start of drying
M Measured value at each print interval
N Total time of drying
O Dry weight of the sample in grams
P Final result in the selected display mode
Q Date and time at the end of the measu-

rement

Menu overview

Menu

▼

Balance-Adjustment
and -Test

Heating module-Adjustment
and -Test

Reset to factory
settings

Clear method memory
clear completely

Enter current 1
time

Enter current 2
date

Set vibration 3
adapter

Automatic/manual 4
sample champer

Functions

Settings

∑CAˆ

†CAˆ

FC†SEÎ

µCLÈ

TIMË

DAÎ

VIBRÅ

STARÎ

NONO

NO

NONO
YES
TEST

NONO

NO

NONO
YES
TEST

NONO

NO

NONO
YES

NONO

NO

NONO
YES

1‹041‹04

1‹04

1‹041‹04

2{0“032{0“03

2{0“03

2{0“032{0“03

MEflMEfl

MEfl

MEflMEfl
HIGH
LOW

AUTøAUTø

AUTø

AUTøAUTø
MA~

ABORT?ABORT?

ABORT?

ABORT?ABORT?
SET?

ABORT?ABORT?

ABORT?

ABORT?ABORT?
CLEAR?

▼

▼

Set audio signal 5

Protect settings 6

Activate/deactivate 7
symbol display

Switch built-in 8
printer on/off

Activate/deactivate 9
method option

Select dialog
language

▼

BEE∏

KE¥PROÎ

SYMBOˆ

PRINÎ

MET·

DEUTSCHDEUTSCH

DEUTSCH FRANCAIS

DEUTSCHDEUTSCH

LOWLOW

LOW

LOWLOW
HIGH
OFF

OFFOFF

OFF

OFFOFF
ON

ONON

ON

ONON
OFF

ONON

ON

ONON
OFF

ONON

ON

ONON
OFF

ITALIANO
ESPANOL
RUSSIAN
ENGLISH EU
ENGLISH US

Method menu overview

Method

Menu

Free switch-off criterion

(= switch-off criterion F)

Free factor -MC

(correction factor)

Free factor g

(calculated result)

ƒSOé

ƒƒ-Mé

ƒƒ‚

Selecting the setting within a menu item:

Reset

Quits the menu without saving the last menu
item you changed

Saves the menu item and skips to the next
menu item

Menu

Calls up the next menu item

NONO

NO

NONO
YES

NONO

NO

NONO
YES ±000

NONO

NO

NONO
YES 10

'W†M‚'W†M‚

11

'W†M‚

1

'W†M‚'W†M‚

11

'SE© 100

(1-100)

POSPOS

POS

POSPOS
NEG

(1-10 mg)
(5-180 sec)

(0.500-2.000)

▼

Select settings