Mettler Toledo IND439check, IND439xx check, BBA439check User Manual

Download

Page 1

User manual

METTLER TOLEDO Weighing terminal IND439check Weighing terminal IND439xx check Compact scales BBA439check

www.mt.com/support

IND439

Page 2

Congratulations on choosing the quality and precision of METTLER TOLEDO. Proper use according to this Operating Manual and regular calibration and maintenance by our factory-trained service team ensures dependable and accurate operation, protecting your investment. Contact us about a ServiceXXL agreement tailored to your needs and budget.

We invite you to register your product at www.mt.com/productregistration

so we can contact you about enhancements, updates and important notifications concerning your product.

@@@@@

Page 3

Table of contentsIND439check / IND439xx check / BBA439check

3User manual 22015307A 05/08

Table of contents

Page

1 Introduction .....................................................................................5

1.1 Safety instructions for the explosion protected weighing terminal

IND439xx check ............................................................................5

1.2 Safety instructions for non-explosion-protected devices .........................6

1.3 Disposal ..........................................................................................7

1.4 Use in hygienically sensitive areas .....................................................7

1.5 Description ......................................................................................8

1.6 Commissioning ..............................................................................12

2 Operation ......................................................................................15

2.1 Switching on and off .......................................................................15

2.2 Zeroing / Zero point correction ..........................................................15

2.3 Simple weighing .............................................................................15

2.4 Weighing with tare ..........................................................................16

2.5 Displaying the capacity available ......................................................17

2.6 Printing results ...............................................................................17

2.7 Cleaning ........................................................................................17

2.8 Testing of weighing terminal and scale/display of the ID code

(only for weighing terminals with IDNet interface) ...............................18

3 Check weighing .............................................................................19

3.1 Specifying target values ...................................................................19

3.2 Check weighing ..............................................................................23

3.3 Check weighing with "quick start" .....................................................24

3.4 Check weighing to zero ...................................................................24

3.5 Terminating check weighing .............................................................24

4 Settings in the menu ......................................................................25

4.1 Operating the menu ........................................................................25

4.2 Overview .......................................................................................27

4.3 Scale settings (SCALE) – analog ......................................................31

4.4 Scale settings (SCALE) – IDNet .........................................................33

4.5 Application settings (APPLICATION) ..................................................35

4.6 Terminal settings (TERMINAL) ..........................................................37

4.7 Configuring interfaces (COMMUNICATION) .........................................38

4.8 Diagnosis and printing out of the menu settings (DIAGNOS) ................43

5 Interface description ......................................................................44

5.1 SICS interface commands ................................................................44

5.2 TOLEDO Continuous mode ..............................................................46

5.3 MMR interface commands ...............................................................48

6 Event and error messages ..............................................................51

Page 4

Table of contents

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

7 Technical data and accessories ......................................................53

7.1 Technical data ............................................................................... 53

7.2 Accessories ...................................................................................57

8 Appendix ...................................................................................... 59

8.1 Safety checks .................................................................................59

8.2 Tests for utilisation in hygienically sensitive areas .............................. 59

8.3 Working to GMP (Good Manufacturing Practice) ................................60

8.4 Tables of geo values ....................................................................... 60

8.5 FCC ..............................................................................................63

9 Index ............................................................................................64

Page 5

IntroductionIND439check / IND439xx check / BBA439check

5User manual 22015307A 05/08

1 Introduction

1.1 Safety instructions for the explosion protected weighing terminal IND439xx check

The device fulfils Device category 3 and is approved for operation in Zone 2 (gases) and Zone 22 (dusts) hazardous areas.

There is an increased risk of injury and damage when used in hazardous areas.

Special care must be taken when working in such hazardous areas. The code of practice is oriented to the "Safe Distribution" concept drawn up by METTLER TOLEDO.

Competence ▲ The device, accompanying weighing platforms and accessories may only be

installed, maintained and repaired by authorized METTLER TOLEDO service personnel.

▲ The mains connection may only be connected or disconnected by the owner’s

electrician.

Ex approval ▲ For the exact specification please refer to the statement of conformity.

▲ No modifications may be made to the terminal and no repair work may be

performed on the modules. Any weighing platform or system modules that are used must comply with the specifications contained in the installation instructions. Non-compliant equipment jeopardizes the safety of the system, cancels the Ex approval and renders any warranty or product liability claims null and void.

▲ The cable glands must be tightened so that a strain relief of ≥ 20 N per mm cable

diameter is ensured.

▲ When connecting external devices, always observe the maximum permissible

connected loads, refer to the installation instructions. It must be ensured that no voltages are fed into the device than it itself provides. The interface parameters have to fulfil the standard.

▲ Peripheral devices without an Ex approval may only be operating in non-

hazardous areas. It must be ensured that no voltages are fed into the device than it itself provides. In addition the maximum permissible connected loads have to be observed, refer to the installation instructions. The interface parameters have to fulfil the standard.

▲ The safety of the weighing system is only guaranteed when the weighing system

is operated, installed and maintained in accordance with the respective instructions.

Page 6

Introduction

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

Ex approval ▲ Also comply with the following:

– the instructions for the system modules, – the regulations and standards in the respective country, – the statutory requirement for electrical equipment installed in hazardous areas

in the respective country,

– all instructions related to safety issued by the owner.

▲ Before initial start-up and following service work, check the explosion protected

weighing system for the proper condition of all safety-related parts.

Operation ▲ Prevent the build-up of static electricity. Therefore:

– always wear suitable working clothes when operating or performing service

work on the system,

– do not rub or wipe off the keyboard surface with a dry cloth or glove.

▲ Do not use protective hoods.

▲ Prevent damage to the weighing terminal. Hairline cracks in the keyboard

membrane are also considered damage.

▲ If the weighing terminal, accompanying weighing platforms or accessories are

damaged:

– Switch off weighing terminal. – Separate the weighing terminal from the mains in accordance with the

applicable regulations.

– Secure the weighing terminal against accidental start-up.

▲ Always charge the storage batteries in a safe zone.

▲ Ensure that the supply voltage at the installation site amounts to 230 V.

1.2 Safety instructions for non-explosion-protected devices

▲ Do not use the device in an hazardous environment!

Special devices are available in our range of products for hazardous environments.

▲ Ensure that the power socket outlet for the device is earthed and easily accessible,

so that it can be de-energized rapidly in emergencies.

▲ Ensure that the supply voltage at the installation site lies within in the range of

100 V to 240 V.

▲ The safety of the device cannot be ensured if it is not operated in accordance with

these operating instructions.

▲ Only authorized personnel may open the device.

▲ Check the power cable regularly for damage. If it is damaged, disconnect the

device immediately from the power supply.

▲ Ensure that there is a space of at least 3 cm at the rear in order to prevent the power

cable from being bent too strongly.

Page 7

IntroductionIND439check / IND439xx check / BBA439check

7User manual 22015307A 05/08

1.3 Disposal

In conformance with the European Directive 2002/96 EC on Waste Electrical and Electronic Equipment (WEEE) this device may not be disposed of with domestic waste. This also applies to countries outside the EU, per their specific requirements.

➜ Please dispose of this product in accordance with local regulations at the collecting

point specified for electrical and electronic equipment.

If you have any questions, please contact the responsible authority or the distributor from which you purchased this device.

Should this device be passed on to other parties (for private or professional use), the content of this regulation must also be related.

Thank you for your contribution to environmental protection.

If the device is equipped with a storage battery:

The nickel metal hydride (NiMH) storage battery does not contain any heavy metals. However, it may not be disposed of with the normal refuse.

➜ Observe the local regulations on the disposal of materials that are hazardous to the

environment.

1.4 Use in hygienically sensitive areas

The device is suitable for use in hygienically sensitive areas. It fulfils the following requirements on areas coming into contact with the product (keyboard) and areas not coming into contact with the product (housing, stand):

• Suitability of the materials for contact with foodstuffs

• Continuous bonding joints that do not act on the material

• Smooth, non-porous and flat surfaces that are easy to clean

• Continuous welding seams

• No sharp corners

For further information please refer to Sections 8.2 and 8.3.

Page 8

Introduction

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

1.5 Description

1.5.1 Weighing terminals IND439check and IND439xx check

METTLER TOLEDO weighing platforms can be connected without problems to the weighing terminals.

The weighing terminals are available in two different basic versions: for connecting analog scales or for digital scales with IDNet interface.

Both basic versions are supplied by default with in-built power supply unit and an RS232 interface.

IND439xx check is approved for use in hazardous areas of the Category 3.

1.5.2 Compact scale BBA439check

The compact scale BBA439check consists of a terminal-stand combination that is connected to an analog weighing platform of the PBA430 series.

The compact scale is supplied by default with an in-built power supply unit and an RS232 interface.

1.5.3 Additional equipment

The following alternatives are also possible:

• Power supply via in-built storage battery

• Version for external power supply 12 – 24 V DC

• Power supply via an external storage battery (not for IND439xx check)

• Additional second communication interface

One of the following options is available as the second communication interface:

• RS232

• RS485/RS422

• Ethernet interface

• USB interface

• Digital I/O

• WLAN

Page 9

IntroductionIND439check / IND439xx check / BBA439check

9User manual 22015307A 05/08

1.5.4 Overview

1 Keys

2 Display

3 Measuring data sign

1 Power supply

connection

2 Pressure compensation

3 Equipotential bonding

terminal, only for IND439xx check

4 COM1 interface

5 COM2 interface

(optional)

6 Antenna for optional

WLAN interface

7 not assigned

8 Scale connection

9 Securing plate for the

interface connections, only for IND439xx check

Weighing terminal connections

1 67432

Page 10

Introduction

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

1.5.5 Display

1 COM1 interface

2 COM2 interface

(optional)

3 Antenna for optional

WLAN interface

4 Pressure compensation

5 Power supply

connection

6 Scale connection

Compact scale connections

1 2

1 7-segment display, 7 digits, with decimal point

2 Notation for weight values with e = 10 d

3 Active interface

4 Symbol for displaying gross and net values

5 Active scale

6 Weighing range display

7 Charge state of the storage battery, only for devices with storage battery

8 Weight units

9 Display of additional information, e.g. tolerance mode

10 not used

11 not used

12 Graphics display of the weighing range, display for check weighing

13 Standstill check (goes out when a stable weight value has been reached)

14 Sign

15 Notation for modified or calculated weight values, e.g. higher resolution, weight

below minimum value

1 45 6

101112

Page 11

IntroductionIND439check / IND439xx check / BBA439check

11User manual 22015307A 05/08

1.5.6 Keyboard

Main functions

Additional functions

Key Function in the operating mode Function in the menu

Switch the terminal on/off; cancel To the last menu item –End–

Set scale to zero, delete tare Long keypress at scales with IDNet

interface: Display of the ID code and checking of the calibration

Page backwards

Tare scale, delete tare Page forwards

Transfer key Long keypress: Call up menu

Activate menu item Accept selected setting

Key Function

Call up data record Long keypress: Store data record

In weighing mode: Switch over weight unit When entering target values: Switch over tolerance mode In the memory: Display the stored results

At entries: Switch to the next digit

At entries: Increase digit by 1 In the memory: with a short keypress: change to the next memory,

with a long keypress: jump 10 memory entries further

At entries: Decrease digit by 1 In the memory: with a short keypress: change to the previous memory,

with a long keypress: jump 10 memory entries back

Determine target value and/or tolerances

Page 12

Introduction

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

1.6 Commissioning

The weighing platform connection to the weighing terminals IND439check / IND439xx check as well as the commissioning of the interfaces are described in the "IND4x9 / BBA4x9" installation instructions.

➜ Call the METTLER TOLEDO service or carry out commissioning in accordance with

the installation instructions.

1.6.1 Limited mobility at explosion protected weighing terminal IND439xx check

CAUTION!

The device may only be operated in Zone 2 and 22 hazardous areas.

▲ Protect data and signal cable extensions against inadvertent disconnection. ▲ Secure the interface connections on the rear using the interface plate.

1.6.2 Labelling for operation in hazardous area

The following signs must be mounted on the device, accompanying weighing platforms and accessories so that they are clearly visible:

• Model plate and the device’s model data, manufacturer and serial number

• Safety instructions

• Explosion protection identification

• If appropriate, temperature range

1.6.3 Establishing a mains connection at an explosion protected weighing terminal IND439xx check

CAUTION!

The mains connection may only be connected by the owner’s electrician.

CAUTION!

The device only operates correctly at a supply voltage of 230 V. ▲ Do not under any circumstances connect the device if the voltage value on the

rating plate deviates from the local system voltage.

▲ Only connect the device to an earthed mains connection. ▲ Ensure that equipotential bonding has been implemented.

Page 13

IntroductionIND439check / IND439xx check / BBA439check

13User manual 22015307A 05/08

1.6.4 Establishing a mains connection at non-explosion-protected devices

CAUTION!

Before connecting the power supply check whether the voltage value printed on the rating plate agrees with the local system voltage.

▲ Do not under any circumstances connect the device if the voltage value on the

rating plate deviates from the local system voltage.

➜ Plug the power plug into the power socket.

After it has been connected, the device carries out a self-testing routine. The device is ready to operate when the zero display appears.

1.6.5 Devices with built-in or external storage battery

CAUTION!

Explosion hazard! ▲ In the case of explosion protected devices the storage battery may only be charged

in a safe area.

CAUTION!

Danger of soiling! The charger for the storage battery is not protected to IP69K.

▲ Do not charge the device in humid or dusty rooms. ▲ After the internal storage battery has been charged, close the cover cap of the

charging socket at the device.

▲ Close the cover cap of the charging socket again at an external storage battery. ▲ In order to maintain degree of protection IP69K, make sure at devices with an

external storage battery that the external storage battery is connected firmly to the device. Ensure that the plug connector of the external storage battery is inserted into the socket outlet of the device until it will go no further.

Note The storage battery is also suitable for permanent mains operation.

➜ In order to obtain the full nominal capacity we recommend that you discharge the

storage battery at regular intervals (approx. every 4 weeks) through normal operation.

The operating life depends on the intensity of use, the configuration and the connected scale. For details see Section 7.1.2.

The battery symbol shows the current charge state of the storage battery. 1 segment corresponds to approx. 25% capacity. If the symbol flashes, the storage battery has to be charged. If work is continued during the charging process, the charging time is extended. The storage battery is protected against overcharging.

The charging time of the storage battery amounts to approx. 6 hours. If the device continues to be operated during the charging process, the charging time is extended. The storage battery has a service life of approx. 1,000 charging/discharging cycles.

Page 14

Introduction

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

1.6.6 Devices with external power supply 12 – 24 V DC

Explosion protected weighing terminals IND439xx check

The device is supplied with a fixed-mounted 2.5 m long connecting cable with open ends.

Connection values: 12 – 24 V DC, max. 800 mA.

Non-explosion-protected devices

The device is equipped with a socket for connecting the power supply.

Connection values: 12 – 24 V DC, max. 800 mA.

A connecting cable with open ends is included with the device.

CAUTION!

Danger of soiling! ▲ In order to maintain degree of protection IP69K, make sure at devices with an

external power supply that the connecting cable is connected firmly to the device. Ensure that the plug connector of the connecting cable is inserted into the socket outlet of the device until it will go no further.

1.6.7 Verification at partially verified scales

Partially verified scales (scales with first-stage verification) and scales with IDNet interface have to be verified by an authorized office or the METTLER TOLEDO Service.

➜ Call the METTLER TOLEDO Service.

Note Adjust non-verified analog scales for the maximum precision, refer to Section 4.3.1.

Page 15

OperationIND439check / IND439xx check / BBA439check

15User manual 22015307A 05/08

2 Operation

2.1 Switching on and off

Switching on ➜ Press .

The scale conducts a display test. Afterwards the software version identifier is displayed. When the weight display appears, the scale is ready to weigh.

Note

If is pressed for a long time while switching on, the serial number of the device is also displayed after the software version identifier.

Switching off ➜ Press .

Before the display goes out, -OFF- appears briefly.

2.2 Zeroing / Zero point correction

Zeroing corrects the influence of slight changes on the load plate or minor deviations from the zero point.

Manual 1. Unload scale.

2. Press .

The zero display appears.

Automatic In the case of scales that cannot be certified, the automatic zero point correction can

be deactivated in the menu or the amount can be changed. Verified scales are set fixed to 0.5 d.

As standard, the zero point of the scale is automatically corrected when the scale is unloaded.

2.3 Simple weighing

1. Place weighing sample on scale.

2. Wait until the stability monitor goes out.

3. Read weighing result.

Page 16

Operation

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

2.4 Weighing with tare

2.4.1 Taring

➜ Place the empty container on the scale and press .

The zero display and the symbol NET appear.

The tare weight remains saved until it is cleared.

2.4.2 Clearing the tare

➜ Unload scale and press .

The symbol NET goes out, the zero display appears.

If A.CL-tr is activated in the menu under SCALE –> tArE, the tare weight is auto- matically cleared as soon as the scale is unloaded.

2.4.3 Automatic taring

Prerequisite

A-tArE is activated in the menu under SCALE –> tArE, the symbol T flashes in the display.

The packaging material must be heavier than 9 display steps of the scale.

➜ Place the container or packaging material on the scale.

The packaging weight is automatically saved as the tare weight, the zero display and the symbol NET appear.

2.4.4 Chain tare

Prerequisite

The tare function CHAIn.tr is activated in the menu under SCALE –> tArE.

With this function it is possible to tare several times if, for example, cardboard is placed between individual layers in a container.

1. Place the first container or packaging material on the scale and press .

The packaging weight is automatically saved as the tare weight, the zero display and the symbol NET appear.

2. Weigh the weighing sample and read/print out the result.

3. Place the second container or packaging material on the scale and press

again.

The total weight on the scale is saved as the new tare weight. The zero display appears.

4. Weigh the weighing sample in the second container and read/print the result.

5. Repeat the last two steps for other containers.

Page 17

OperationIND439check / IND439xx check / BBA439check

17User manual 22015307A 05/08

2.5 Displaying the capacity available

The scale has a graphic display of the scale capacity available. The bar indicates how many per cent of the scale capacity is already occupied and what capacity is still available. In the example, approx. 65 % of the scale capacity is occupied.

2.6 Printing results

If a printer or computer is connected to the scale, the weighing results can be printed out or sent to a computer.

➜ Press .

The display contents are printed out or transferred to the computer.

2.7 Cleaning

The device conforms to degree of protection IP69K to DIN 40050.

It is suitable for hygienically sensitive areas - see the proofs in Section 8.2.

The device is designed so that it can be cleaned easily. The housing is made of stainless steel 1.4301 (AISI 304), the keyboard of resistant polyester (PE). If required, high-pressure equipment can be used for cleaning.

Cleaning

• Close open connectors with cap plugs.

• Clean the protective hood of the non-explosion-protected devices separately. The

protective hood is dishwasher-proof.

• Replace protective hoods regularly.

• Use a moist cloth for minor soiling.

• Do not use acids, alkaline solutions or strong solvents.

• Observe the following limits when using high-pressure equipment:

– Max. water temperature 80 °C / 176 °F – Max. water pressure 8,000 kPa (80 bars) – Min. distance jet nozzle to terminal 50 cm – Do not point the jet at one point for longer than 10 seconds – Water flow rate not greater then 10 l/min

• Observe all the existing regulations on cleaning intervals and permissible cleaning

agents.

Information on cleaning the weighing platform connected to the weighing terminal

➜ Be sure to observe the cleaning instructions for the connected weighing platform.

The weighing platform may not be designed for cleaning with high-pressure equipment.

Page 18

Operation

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

2.8 Testing of weighing terminal and scale/display of the ID code (only for weighing terminals with IDNet interface)

The ID code is increased by 1 at every calibration in case of IDNet scales. For verified scales, the ID code displayed by the weighing terminal must match the ID code on the ID cards. Otherwise, the verification is no longer valid.

2.8.1 Displaying the ID code

1. Unload weighing platform.

2. Press the key and keep it pressed until the display changes to -----.

The ID code is then displayed: COdE=...

2.8.2 Testing the weighing platform and terminal

➜ After the ID code is displayed, press the key again.

CHE CAL is displayed. The weighing platform is tested.

After a successful test CAL ok is displayed briefly.

The terminal then changes to normal operation.

Note If a calibration error CAL Err is displayed during testing, repeat the test. If the error

is displayed again, inform the METTLER TOLEDO Service.

Page 19

Check weighingIND439check / IND439xx check / BBA439check

19User manual 22015307A 05/08

3 Check weighing

The device disposes of additional functions for check weighing. The corresponding settings in the menu are described in Section 4.5.

The corresponding colored background lighting allows rapid understanding of the states "too light" (factory setting: red), "good" (factory setting: green) and too heavy" (factory setting: yellow). The colors can be modified in the menu, refer to Page 35.

3.1 Specifying target values

Different entries are required at the beginning of check weighing, depending on the setting for the tolerance mode.

• Tolerance mode Absolute (factory setting): The lower (LOW) and upper (HIGH)

tolerance values have to be specified. The target weight is calculated automatically as the mean value of the two tolerance values

• Tolerance mode Relative: The target weight (tArGEt) as well as the lower

(tOL–) and upper (tOL+) tolerance values have to be specified. The tolerances have to be entered as relative deviations from the target value.

• Tolerance mode Percentage: The target weight (tArGEt) as well as the lower

(tOL–) and upper (tOL+) tolerance values have to be specified. At check weighing the weight value is represented as a percentage of the target weight. In check weighing mode the target weight 100 % is striven for, or 0 % at check weighing to zero.

3.1.1 Weighing in target values

The following section describes the course of the factory setting for the CHECK application.

With operator guidance

1. Press .

The check weighing mode is activated. The color of the display background changes. Depending on the tolerance mode setting, (LOW) or (tArGEt) is requested as the first weight value. The set tolerance mode is shown in the lower right-hand corner with the characters A (absolute), r (relative) and P (percent- age).

2. If desired, use to change the tolerance mode.

3. Place the required weight on the scale and press .

The color of the display background changes again. The next weight value is requested.

4. Repeat Step 3 until no further weight values are requested.

The scale is ready for check weighing.

Page 20

Check weighing

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

Note • The applied weights can also be confirmed with .

• The upper tolerance value has to be higher than the lower one (HIGH > LOW)

respectively the target weight has to be higher than the lower tolerance value (TARGET > TOL–).

Alternatively

1. Place the weight on the scale and press .

Depending on the tolerance mode setting, this weight value is stored as the lower tolerance value (LOW) or as the target weight (tArGEt). The set tolerance mode is shown in the lower right-hand corner with the characters A (absolute), r (relative) and P (percentage).

The color of the display background changes, the next weight value is requested.

2. Place the required weight on the scale and press .

The color of the display background changes again. A further weight value is requested in the tolerance mode settings r (relative) and P (percentage).

3. If necessary, repeat Step 2.

The scale is ready for check weighing.

Note The second and, if appropriate, third weight value can also be confirmed with .

Page 21

Check weighingIND439check / IND439xx check / BBA439check

21User manual 22015307A 05/08

3.1.2 Specifying target values numerically

The following section describes the course of the factory setting for the CHECK application.

1. Unload the scale and press .

The check weighing mode is activated. Depending on the tolerance mode setting, (LOW) or (tArGEt) is requested as the first weight value.

2. Press .

The weight display appears with a flashing first number.

3. Change the number using the keys and .

4. Use to accept the number and change to the next position.

5. Enter all further numbers as described.

6. Confirm the entered weight value using .

The color of the display background changes again. The next weight value is requested.

7. Press .

The weight display appears with a flashing first number.

8. Enter the requested weight value and confirm with .

The color of the display background changes again. The next weight value is requested.

9. Repeat the entry until no further weight values are requested.

The scale is ready for check weighing.

Note In the tolerance modes r (relative) and P (percentage) the same value is automati-

cally suggested for the upper tolerance value (tOL+) as for the lower tolerance value (tOL–) after has been pressed. If symmetrical tolerance values are required, the suggested value can be accepted directly by pressing .

3.1.3 Using stored target values

Storing target values

1. Enter the target values as described in Section 3.1.1 or 3.1.2.

2. Keep pressed approx. 3 seconds long.

The display changes to green (factory setting for the state "good") and the message FrEE appears. The number of the first free memory is displayed in the lower righthand corner.

3. If appropriate, press the keys or until the desired memory slot appears. If the key is pressed for a longer time, the system jumps 10 slots.

4. Press or .

StOrEd appears briefly in the display. The target value is stored under the selected number.

Page 22

Check weighing

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

Note If the selected memory slot is already occupied, the background lighting changes to

red (factory setting for the state "too light"). ➜ In order to overwrite the slot with the new values, press .

The message SurE? appears. Press again.

-or-

➜ To abort the procedure press . ➜ Press again or the keys or in order to return to the next free mem-

ory slot.

Loading the target values

1. Press .

The first occupied memory slot is displayed with its first value.

2. If appropriate, press the keys or until the desired memory slot appears.

3. Press again.

The message LOAd and the stored values are displayed in rapid succession.

Then the scale is ready for check weighing.

Alternatively

1. Press .

2. Select the desired storage number with the keys or .

Note With the article parameters (such as the target values, tolerance mode, etc.) of

the selected memory slot are displayed.

Page 23

Check weighingIND439check / IND439xx check / BBA439check

23User manual 22015307A 05/08

3.2 Check weighing

The device facilitates check weighing through different colored background lighting for the states "too light" (factory setting: red), "good" (factory setting: green) and "too heavy" (factory setting: yellow).

1. Enter or load the target values as described in Section 3.1.

2. Place the check weighing material on the scale.

Depending on the applied weight the color of the background lighting changes. The weight value is displayed in accordance with the tolerance mode setting.

Display at check weighing

In addition to the colored background lighting the graphics display provides support in particular during dispensing procedures. The following overview lists the colors of the factory setting.

Target values Display Color Meaning

Absolute

Low = 0.950 kg High = 1.050 kg

Relative

Target = 1.000 kg Tol– = 0.050 kg Tol+ = 0.050 kg

Red Too light

Weight below the lower tolerance value

Green Good

Weight within the tolerance values

Yellow Too heavy

Weight above the upper tolerance value

Percent

Target = 1.000 kg Tol– = 5 % Tol+ = 5 %

Red Too light

Weight below the lower tolerance value

Green Good

Weight within the tolerance values

Yellow Too heavy

Weight above the upper tolerance value

Page 24

Check weighing

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

3.3 Check weighing with "quick start"

If fixed stored tolerance value are used in the tolerance mode r (relative) or P (per- centage), check weighing can be started by pressing just one key.

Prerequisite

• The setting YES is selected in the menu under APPLIC –> CHECK –> tOL-

ErAN –> dEFAULt –> USE .

• Tolerance values are defined under APPLIC –> CHECK –> tOLErAN –>

dEFAULt –> VALUES .

Course ➜ Place the target weight on the scale and press .

The applied weight is stored as the target weight. The display changes to the state "good" (factory setting = green).

The check weighing mode is activated.

3.4 Check weighing to zero

The weight value can also be represented as the difference to the target weight.

Prerequisite

• rELAtIV or PErCENt is selected under APPLIC –> CHECK –> tOLErAN –

> MOdE.

• tO ZErO is selected under APPLIC –> CHECK –> dISPLAY –> MOdE .

Course 1. Enter or load the target values as described in Section 3.1 or 3.3.

The target weight is displayed with a negative preceding sign.

2. Place the check weighing material on the scale.

Depending on the applied weight the color of the background lighting changes. The weight value is displayed in accordance with the tolerance mode setting. The target weight is 0 (kg) or 0.00 %.

3.5 Terminating check weighing

Prerequisite

The weight display shows the gross weight 0.

1. Press .

Depending on the set tolerance mode tArGEt or Low is displayed.

2. Press again.

The device operates in normal weighing mode.

Page 25

Settings in the menuIND439check / IND439xx check / BBA439check

25User manual 22015307A 05/08

4 Settings in the menu

Settings can be changed and functions can be activated in the menu. This enables adaptation to individual weighing requirements.

The menu consists of 6 main blocks containing various submenus on several levels.

4.1 Operating the menu

4.1.1 Calling up the menu and entering the password

The menu differentiates between 2 operating levels: Operator and Supervisor. The Supervisor level can be protected by a password. When the device is delivered, both levels are accessible without a password.

Operator menu 1. Press and keep it pressed until COdE appears.

2. Press again.

The menu item tErMINL appears. Only the submenu dEVICE is accessible.

Supervisor menu 1. Press and keep it pressed until COdE appears.

2. Enter the password and confirm with .

The first menu item SCALE appears.

Note No supervisor password has been defined when the device is first delivered. Therefore,

respond to the password inquiry with when you call up the menu for the first time. If a password has still not been entered after a few seconds, the scale returns to weigh-

ing mode.

Emergency password for Supervisor access to the menu

If a password has been issued for Supervisor access to the menu and you have forgotten it, you can still enter the menu:

➜ Press 3 times and confirm with .

Page 26

Settings in the menu

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

4.1.2 Selecting and setting parameters

Scrolling on one level ➜ Scroll forward: Press .

➜ Scroll back: Press .

Activating menu items/

accepting selection

➜ Press .

Exiting menu 1. Press .

The last menu item End appears.

2. Press .

The inquiry SAVE appears.

3. Confirm inquiry with to save the settings and return to weighing mode.

-or-

➜ Press to discard changes and return to weighing mode.

Note The SCALE menu block depends on the built-in scale interface.

SCALE

APPLIC

tErMINL COMMUNI

dIAGNOS

End

CAL dISPLAY tArE

T T T

T T

SLEEP

PWr.OFF b.LIGHt

MOdE

COM 1

...

PriNtEr PArAMEt

dEVICE ACCESS

COdE

rESEt

COM 2

...

rSt.COMX

Page 27

Settings in the menuIND439check / IND439xx check / BBA439check

27User manual 22015307A 05/08

4.2 Overview

Factory settings are printed bold in the following overview.

Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Page

SCALE CAL 31

(analog) dISPLAY UNIt1 g, kg, oz, lb, t 31

UNIt2 g, kg, oz, lb, t

rESOLU

UNt.rOLL ON, OFF

tArE A-tArE ON, OFF 31

ChAIn.tr ON, OFF

A.CL-tr ON, OFF, 9 d

ZErO AZM OFF; 0.5 d; 1 d; 2 d; 5 d; 10 d 31

rEStArt ON, OFF 32

FILtEr VibrAt LOW, MEd, HIGH, 32

PrOCESS UNIVEr, dOSING

StAbILI FASt, StAndrd, PrECISE

Min.WEiG ON/OFF ON, OFF 32

rESEt SUrE? 32

SCALE dISPLAY UNIt2 g, kg, oz, lb, t 33

(IDNet) UNt.rOLL ON, OFF

tArE A-tArE ON, OFF 33

ChAIn.tr ON, OFF

A.CL-tr ON, OFF, 9 d

ZErO AZM ON, OFF 33

rEStArt ON, OFF 33

FILtEr VibrAt StAbLE, nOrMAL, UnStAbL, 34

PrOCESS FinEFiL, UNIVErS, AbSOLUt

StAbILI ASd=0, ASd=1, ASd=2, ASd=3, ASd=4

UPdAtE Setting possibilities depend on the connected scale 34

Min.WEiG ON/OFF ON, OFF 34

rESEt SUrE? 34

Page 28

Settings in the menu

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

APPLIC CHECk tOLErAN MOdE ABSOLUt, rELAtIV,

PErCENt

dEFAULt USE No, YES

VALUES rELAtIV,

PErCENt

dISPLAY MOdE NOrMAL, tO ZErO,

StEALtH

BACK.COL SP.tOL–

tOL–

GOOd

tOL+

OUtPUt SP.tOL– 36

SP.tOL-– 36

SENdMOd CONtINU, StAbLE

G.PrINt YES, NO

ACCESS SAVE UNLOCK, LOCK 36

rECALL UNLOCK, LOCK

tArGEt UNLOCK, LOCK

MEMOrY CLEAr.M SUrE? 37

rESEt SUrE? 37

tERMINL dEVICE SLEEP OFF, 1 min, 3 min, 5 min, 15 min,

30 min

PWr OFF OFF, 1 min, 3 min, 5 min, 15 min,

30 min

b.LIGHt ON/OFF ON, OFF, 5 sec, 10 sec,

30 sec, 1 min

BACK.COL

ACCESS SUPErVI 38

rESEt SUrE? 38

Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Page

Page 29

Settings in the menuIND439check / IND439xx check / BBA439check

29User manual 22015307A 05/08

COMMUNI COM 1/COM 2 MOdE Print 39

A.Print

CONtINU

dIALOG

MMr

MMr.A.SIr

CONt.OLd

dIAL.OLd

dt-b GrOSS ON, OFF

tArE ON, OFF

nEt ON, OFF

dt-G GrOSS ON, OFF

tArE ON, OFF

nEt ON, OFF

COnt-Wt

2nd.dISP

InSt.Prn

PriNtEr tYPE ASCII, GA46 40

tEMPLat StdArd, tEMPLt1,

tEMPLt2

ASCi.Fmt LINE.FMt MULtI

SINGLE FIXEd

LENGtH 1 ... 24 ... 100

SEPArAt , ; ...

Add LF 0 ... 9

PArAMEt bAUd 300 ... 2400 ... 38400 40

PAritY 7 nonE, 8 nonE, 7 odd,

8 odd, 7 EVEN, 8 EVEN

H.SHAKE NO, XONXOFF, nEt 422,

nEt 485

NEt.Addr 0 ... 31

ChECSuM ON, OFF

Vcc ON, OFF

rSt.COMx SUrE? 40

Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Page

Page 30

Settings in the menu

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

COMMUNI OPtION EtH.NEt IP.AddrS, SUbNEt, GAtEWAY 41

WLAn IP.AddrS, SUbNEt, GAtEWAY, SIGNAL

USb USb tESt

diGitAL IN 0 ... 3 OFF, ZErO, tArE,

Print, UNIt, rECALL, SAVE, tArGEt, Arr.rIG, Arr.UP, Arr.DOWN, StArt

OUt 0 ... 3 OFF, StAbLE, tArE,

bEL.Min, AbV.Min, UndErLd, OVErLd, StAr, SP.tOL–, SP.tOL--, tOL–, GOOd, tArGEt, tOL+

dEF.PrN tEMPLt1/

tEMPLt2

LINE 1 ... LINE 12

NOt.USEd, HEAdEr, GrOSS, tArE, nEt, tArGEt, dEVIAt, tOL–, tOL+, tOL.tYP, StArLN, CrLF, F.FEEd

dIAGNOS tESt SC 43

KboArd

dISPLAY

SNr

LiSt

LiSt.M

rESEt.AL SUrE?

Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Page

Page 31

Settings in the menuIND439check / IND439xx check / BBA439check

31User manual 22015307A 05/08

4.3 Scale settings (SCALE) – analog

4.3.1 CAL – calibration (adjustment)

This menu item is not available for certified scales.

4.3.2 DISPLAY – weighing unit and display accuracy

4.3.3 TARE – tare function

4.3.4 ZERO – automatic zero update

CAL 1. Unload scale.

2. Activate menu item CAL with . The scale determines the zero point. –0- appears in the display. The calibration weight to be placed on the scale then flashes in the display.

3. If necessary, change the weight value displayed with .

4. Place the calibration weight on the scale and confirm with .

The scale calibrates with the calibration weight loaded. After calibration is completed, -donE- appears briefly in the display, and the scale automatically returns to weighing mode.

In order to achieve particularly high precision, calibrate under full load.

UNIt1 Select weighing unit 1: g, kg, oz, lb, t

UNIt2 Select weighing unit 2: g, kg, oz, lb, t

rESOLU Select readability (resolution), model-dependent

UNt.rOLL When UNT.rOLL is switched on, the weight value can be displayed in all available

units with .

Notes

• In the case of certified scales individual sub-items of the dISPLAY menu item

may not be available or only to a limited extent, depending on the respective country.

• On dual-range/dual interval scales, resolutions marked with |<–>| 1/2 are

divided up into 2 weighing ranges / intervals, e.g. 2 x 3000 d.

A-tArE Switching on/off automatic taring

CHAIn.tr Switching on/off chain tare

A.CL-tr Switching on/off automatic clearing of the tare weight when the load is removed from

scale Possible settings: OFF, ON, 9 d

AZM On certified scales, this menu item does not appear.

Switching on/off automatic zero update and selecting zeroing range. Possible settings: OFF; 0.5 d; 1 d; 2 d; 5 d; 10 d

Page 32

Settings in the menu

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

4.3.5 RESTART – automatic saving of zero point and tare value

4.3.6 FILTER – adaptation to the ambient conditions and the weighing type

4.3.7 MIN.WEIG – minimum weight

This menu item appears only if the service technician has saved a minimum weight.

4.3.8 RESET – resetting scale settings to factory settings

ON/OFF When the Restart function is activated, the last zero point and tare value are saved.

After switching off / on or after a power interruption, the device continues to work with the saved zero point and tare value.

VIbrAt Adaptation to the ambient conditions

LOW

• Very steady and stable environment. The scale works very rapidly, but is very

sensitive to external influences.

MEd

• Normal environment. The scale operates at medium speed.

HIGH

• Restless environment. The scale works more slowly, but is insensitive to external

influences.

PrOCESS Adaptation to the weighing process

UNIVEr

• Universal setting for all weighing samples and normal weighing goods

dOSING

• Dispensing liquid or powdery weighing samples

StAbILI Adjusting the stability detector

FASt

• The scale operates very fast.

StAndrd

• The scale operates at medium speed.

PrECISE

• The scale operates with the greatest possible reproducibility.

The slower the scale works, the greater the reproducibility of the weighing results.

ON/OFF Switching minimum weight function on/off

If the weight on the scale falls below the stored minimum weight, an * appears on the display in front of the weight indicator.

SUrE? Confirmation inquiry

• Reset the scale settings to factory settings with

• Do not reset scale settings with

Page 33

Settings in the menuIND439check / IND439xx check / BBA439check

33User manual 22015307A 05/08

4.4 Scale settings (SCALE) – IDNet

4.4.1 DISPLAY – weighing unit

4.4.2 TARE – tare function

4.4.3 ZERO – automatic zero update

4.4.4 RESTART – automatic saving of zero point and tare value

UNIt2 Select weighing unit 2: g, kg, oz, lb, t

Notes

• In the case of certified scales individual sub-items of the dISPLAY menu item

may not be available or only to a limited extent, depending on the respective country.

• For two-range/two-interval scales, resolutions identified with |<–>| 1/2 are

divided into the 2 weighing ranges/intervals, for example 2 x 3000 d.

A-tArE Switching on/off automatic taring

CHAIn.tr Switching on/off chain tare

A.CL-tr Switching on/off automatic clearing of the tare weight when the load is removed from

scale Possible settings: OFF, ON, 9 d

AZM On certified scales, this menu item does not appear.

Switching on/off automatic zero update. The effective range of the zero update mode (0.5 d, 1.0 d, 3.0 d) can only be set

by service technicians in case of IDNet scales. Factory setting: 0.5 d

ON/OFF When the Restart function is activated, the last zero point and tare value are saved.

After switching off /on or after a power interruption, the device continues to work with the saved zero point and tare value.

Page 34

Settings in the menu

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

4.4.5 FILTER – adaptation to the ambient conditions and the weighing type

4.4.6 UPDATE – setting the display speed of the weight display

This menu item is only displayed if the UPDATE function is supported by the connected weighing platform.

4.4.7 MIN.WEIG – minimum weighing-in quantity

This menu item appears only if the service technician has saved a minimum weight.

4.4.8 RESET – resetting scale settings to factory settings

VIbrAt Adaptation to the ambient conditions

StAbLE

• Very steady and stable environment. The scale works very rapidly, but is very

sensitive to external influences.

nOrMAL

• Normal environment. The scale operates at medium speed.

UnStAbL

• Restless environment. The scale operates more slowly, but is insensitive to exter-

nal influences.

PrOCESS Adaptation to the weighing process

FinEFiL

• Dispensing of liquid or powdered weighing samples

UniVErs

• Universal setting for all weighing modes and normal weighing samples

AbSOLUt

• For solid bodies under extreme conditions, e.g. strong vibrations

StAbILI ASD = 0 Stability monitoring switched off

Only possible for non-verifiable weighing platforms

ASd=0 ... ASd=4 ASD = 1

ASD = 2 ASD = 3 ASD = 4

Rapid display

⇑ ⇑

Slow display

Good reproducibility ⇓ ⇓ Excellent reproducibility

xx UPS Selecting the number of updates per second (UPS)

Note The possible settings depend on the connected weighing platform.

ON/OFF Switching minimum weight function on/off

If the weight on the scale falls below the stored minimum weight, an * appears on the display in front of the weight indicator.

SUrE? Confirmation inquiry

• Do not reset scale settings with

Page 35

Settings in the menuIND439check / IND439xx check / BBA439check

35User manual 22015307A 05/08

4.5 Application settings (APPLICATION)

4.5.1 CHECK -> TOLERAN – tolerance settings

4.5.2 CHECK-> DISPLAY – display settings

MOdE Set the type of tolerances

ABSOLUt

• Enter the lower and upper tolerance as absolute values

rELAtIV

• Enter the lower and upper tolerance as relative deviations from the target weight

PErCENt

• Enter the lower and upper tolerance as a percentage

Not possible for counting

dEFAULt Working with the specified tolerances. This allows check weighing to be started by

pressing just one key.

USE

• Activate/deactivate specified tolerances

VALUES

• rELAtIV – specify the upper and lower tolerance as a deviation from the target

weight as a weight value

• PErCENt – specify the upper and lower tolerance as a deviation from the target

weight as a percentage

• PIECES – specify the upper and lower tolerance as a deviation from the target

value in pieces

MOdE Display of the current weight value based on the target weight

NOrMAL

• Display of the weight value (at the setting tOLErAN -> MOdE -> ABSOLUt or

tOLErAN -> MOdE -> rELAtIV)

• Display as a percentage of the target weight (at the setting tOLErAN -> MOdE

-> PErCENt)

tO ZErO

• Display of the difference to the target weight

StEALtH

• No weight display, only color display for "too light", "good" and "too heavy"

BACK.COL Color setting of the background lighting for check weighing.

SP.tOL–

• Color setting for weight values below the threshold (SP.tOL–)

tOL–

• Color setting for weight values below the lower tolerance value

GOOd

• Color setting for weight values within the tolerance values

tOL+

• Color setting for weight values above the upper tolerance value

Information on color setting

• The color setting is specified with 3 values for red, green and blue,

for example 7-0-0 for a red background lighting.

• The values can be increased by using the keys lying respectively under them. The

new color value is displayed immediately.

• The total of the 3 color values may amount to a maximum of 8.

• If the setting 0-0-0 is used, the background lighting is disabled.

Page 36

Settings in the menu

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

4.5.3 CHECK -> OUTPUT – setting the output options

4.5.4 CHECK -> ACCESS – protecting keys and functions

SP.tOL– SP.tOL--

Limit for activation of the I/O relay box. The value to be entered is the percentage proportion of the lower tolerance of the target weight/target quantity.

Checking the SP.Tol-- is carried out with the gross weight, for SP.Tol- with the net weight.

SP.Tol- is dependent on SP.Tol--; in other words, if SP.Tol-- has not yet been reached, the SP.Tol- output will not go active.

If both setpoints are used, the SP.Tol-- must be less than SP.Tol-. EXAMPLE Target weight: 2000 g

tOLER+: 2010 g tOLER-: 1990 g SP.tOL-: 010 (%)

The relay box is not activated until 199 g (= 10 % of 1990 g) is reached.

SENd.MOd Specifies the form in which the scale sends information to the I/O relay box and when

the background color changes

CONtINU

• Information is sent permanently, the background color switches over immedi-

ately

StAbLE

• Information is only sent at a stable weight value. The background color is not

switched over until a stable weight value has been reached

G.PrINt Good Print

YES

• Automatic printout when a stable weight value within the tolerance values exists

• No automatic printout

Note The interface has to be set to PrINt for "Good Print". In the setting A.PrINt every

stable weight value is printed out, irrespective of whether it lies within or outside the tolerance values.

SAVE Save target weights and tolerance values

UNLOCK

• Saving by the operator allowed

LOCk

• Saving protected by the Supervisor password

rECALL Recall target weights and tolerance values

UNLOCK

• Recalling by the operator allowed

LOCk

• Recalling protected by the Supervisor password

tARGEt Enter target weights and tolerance values

UNLOCK

• Entering by the operator allowed

LOCk

• Entering protected by the Supervisor password

Page 37

Settings in the menuIND439check / IND439xx check / BBA439check

37User manual 22015307A 05/08

4.5.5 MEMORY – deleting target value memory

4.5.6 RESET – resetting application settings to factory settings

4.6 Terminal settings (TERMINAL)

4.6.1 DEVICE – sleep mode, energy-saving mode and display backlighting

CLEAr.M Delete target value memory

SUrE? Safety prompt

• Press to delete all the target value memories

• Press to not delete the target value memories

SUrE? Confirmation inquiry

• Reset the application settings to factory settings with

• Do not reset the application settings with

SLEEP This menu item only appears on devices in mains operation.

When SLEEP is activated, the scale switches off display and backlighting after the time period set when not in use. The display and backlighting are switched on again at the press of a key or if the weight changes.

Possible settings: OFF, 1 min, 3 min, 5 min, 15 min, 30 min

PWr OFF This menu item only appears on devices in battery operation.

When PWr OFF is activated, the device switches itself off automatically after approx. 3 minutes when not in use. After this, it must be switched on again using

Possible settings: OFF, 1 min, 3 min, 5 min, 15 min, 30 min

Page 38

Settings in the menu

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

4.6.2 ACCESS – password for Supervisor menu access

4.6.3 RESET – resetting terminal settings to the factory settings

b.LIGHt Set the background lighting of the display

ON/OFF Setting whether and after which time the background lighting is to be switched off.

Scales with a storage battery switch the background lighting off automatically by default when no action takes place at the scale for approx. 5 seconds.

Possible settings: OFF (switched off), 5 sec, 10 sec, 30 sec, 1 min, ON (switched on)

BACK.COL Set the color of the background lighting

• The color setting is specified with 3 values for red, green and blue,

for example 7-0-0 for a red background lighting.

• The values can be increased by using the keys lying respectively under them. The

new color value is displayed immediately.

• The total of the 3 color values may amount to a maximum of 8.

• If the setting 0-0-0 is used, the background lighting is disabled.

Notes

• This menu item is accessible without a Supervisor password.

• The time specifications are approximate values.

SUPErVI Password entry for Supervisor menu access

ENtEr.C Request to enter password

➜ Enter the password and confirm with .

rEtYPE.C Request to repeat the password entry

➜ Enter the password again and confirm with .

Notes

• The password can consist of up to 4 characters.

• The key must not be part of the password. It is required for confirming the

password.

• The key may only be used in combination with another key.

• If you enter an impermissible code or make a typing error in the repetition,

COdE.Err. appears in the display.

SUrE? Confirmation inquiry

• Reset terminal settings to the factory settings with

• Do not reset the terminal settings with

Page 39

Settings in the menuIND439check / IND439xx check / BBA439check

39User manual 22015307A 05/08

4.7 Configuring interfaces (COMMUNICATION)

4.7.1 COM1/COM2 -> MODE – operating mode of the serial interface

Print Manual data output to the printer with

A.Print Automatic output of stable results to the printer (e. g. for series weighing operations)

CONtINU Ongoing output of all weight values via the interface

dIALOG Bi-directional communication via MT-SICS commands, control of the scale via PC

MMr Bidirectional communication via MMR commands, controlling of a scale via a PC,

command set compatible to the weighing terminals ID1 and ID3.

MMr.A.SIr Automatic continuous transmission: a stable or dynamic weight value is transmitted

after every measuring cycle.

CONt.OLd As per CONtINU, see above, but with 2 fixed blanks in front of the unit (compatible

with Spider 1/2/3)

dIAL.OLd As per dIALOG, see above, but with 2 fixed blanks in front of the unit (compatible

with Spider 1/2/3)

dt-b DigiTOL-compatible format.

GrOSS

• Transfer of the gross weight, identified with "B"

tArE

• Transfer of the tare weight

nEt

• Transfer of the net weight

dt-G As per dt-b, see above, gross weight identified with "G"

COnt-Wt TOLEDO Continuous mode

2nd.dISP For connecting a second display (automatically activates the 5-V voltage supply at

Pin 9)

InSt.Prn Immediate manual data output to the printer with (not certifiable)

Page 40

Settings in the menu

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

4.7.2 COM1/COM2 -> PRINTER – settings for protocol printout

This menu item only appears if the mode "Print" or "A.Print" is selected.

4.7.3 COM1/COM2 -> PARAMET – communication parameters

4.7.4 COM1/COM2 -> RESET COM1/RESET COM2 – resetting serial interface to factory settings

tYPE Select the printer type

ASCII

• ASCII printer

GA46

• GA46 printer

tEmPLat Selecting protocol printout

StdArd

• Standard printout

tEmPLt1

• Printout in accordance with Template 1

tEmPLt2

• Printout in accordance with Template 2

ASCi.Fmt Selecting formats for the protocol printout

LINE.Fmt

• Line format: MULtI (multiple lines), SINGLE (single lines) or FIXEd

(Records are output in single lines. Every record encompasses the number of character that was defined under LENGtH.)

LENGtH

• Line length: 0 to100 characters, is only displayed at the line format MULtI and

FIXEd

SEPArAt

• Separator: , ; . / \ _ and space; appears only with line format SINGLE

Add LF

• Line feed: 0 ... 9

bAUd Selecting baud rate: 300, 600, 1200, 2400, 4800, 9600, 19200, 38400 baud

PAritY Selecting parity: 7 none, 8 none, 7 odd, 8 odd, 7 even, 8 even

H.SHAKE Select handshake: NO, XONXOFF, NET 422 (network operation via the optional

RS422/RS485 interface via 4-wire bus, only for COM1), NET 485 (network operation via the optional RS422/RS485 interface via 2-wire bus, only for COM1)

NEt.Addr Assigning network address: 0 ... 31, only for NET 485

ChECSuM Activating checksum byte (appears only in TOLEDO Continuous mode)

Vcc Switching 5 V voltage, e.g. for a bar code reader or an optional interface

RS485/422, on/off

SUrE? Confirmation inquiry

• Reset interface settings to factory settings with

• Do not reset the interface settings with

Page 41

Settings in the menuIND439check / IND439xx check / BBA439check

41User manual 22015307A 05/08

4.7.5 OPTION – configuring options

If no option is installed or is not yet configured, N.A. appears in the display.

EtH.NEt Configuration of the Ethernet interface

IP.AddrS

• Enter IP address

SUbNEt

• Enter Subnet address

GAtEWAY

• Enter Gateway address

WLAn Configuration of the WLAN interface

IP.AddrS

• Enter IP address

SUbNEt

• Enter subnet address

GAtEWAY

• Enter gateway address

SIGNAL

• SIG ... shows the signal strength of the WLAN connection as a percentage value.

0 to 25 very weak 26 to 49 weak 50 to 74 good 75 to 100 excellent Reliable operation requires at least a good signal strength.

USb Configuration of the USB interface

USb tESt

• Test of the USB interface. After the test has been passed, rEAdY appears in the

display.

diGitAL Configuration of the digital inputs/outputs

IN 0 ... 3 Configuring inputs 0 ... 3

OFF

• Input not assigned

ZErO

• Key

tArE

• Key

UNIt

• Key

rECALL

• Key , short keypress

SAVE

• Key , long keypress

tArGEt

• Key

Arr.rIG

• Key

Arr.UP

• Key

Arr.DOWN

• Key

StArt

• External key to start the filling application

Page 42

Settings in the menu

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

4.7.6 DEF.PRN – configuring templates

OUt 0 ... 3 Configuring outputs 0 ... 3

OFF

• Output not assigned

StAbLE

• Stable weight value

tArE

• Tare value

bEL.Min

• Value below minimum weight

AbV.Min

• Minimum weight reached or exceeded

UNdErLd

• Underload

OVErLd

• Overload

StAr

• Modified/calculated value

SP.tOL-

• Switching point on, until SP.tOL- is reached (or exceeded)

SP.tOL--

• Switching point on, until SP.tOL-- is reached (or exceeded)

tOL–

• Value below tolerance

GOOd

• Weight within the tolerance

tArGEt

• Target weight

tOL+

• Tolerance value exceeded

tEMPLt1/tEMPLt2 Selecting Template 1 or Template 2

LINE 1 ... 12 Selecting line

NOt.USEd

• Line not used

HEAdEr

• Line as header. The contents of the header must be defined via an interface com-

mand, see Section 5.1.

GrOSS

• Gross weight

tArE

• Tare weight

nEt

• Net weight

tOL–

• Lower tolerance value

tOL+

• Upper tolerance value

tOL.tYPE

• Tolerance mode

StArLN

• Line with ***

CrLF

• Line feed (blank line)

F.FEEd

• Page feed

Page 43

Settings in the menuIND439check / IND439xx check / BBA439check

43User manual 22015307A 05/08

4.8 Diagnosis and printing out of the menu settings (DIAGNOS)

tESt SC Testing the scale

This menu item is only displayed at scales with an analog scale interface.

External Testing scale with external calibration weight

1. The scale checks the zero point. -0- appears in the display. The test weight flashes in the display.

2. If necessary, change the weight value displayed with .

3. Put the calibration weight on the scale and confirm with .

4. The scale checks the calibration weight put on them.

5. After the test is completed, the deviation from the last calibration briefly appears in the display, ideally *d=0.0g, after which the scale changes to the next menu item KboArd.

KboArd Keyboard test

PUSH 1 ... 10

• First press the large keys on the bottom row in order:

• Then press the smaller keys in the top row:

If the key works, the scale changes to the next key.

Note

You cannot abort the keyboard test! If you have selected the menu item KboArd, you must press all keys.

dISPLAY Display test: The scale displays all functioning segments

SNr Display of the serial number

LiSt Printout of a list of all menu settings

LiSt.M Printout of a list of all values and settings in the memory

rESEt.AL Resetting all menu settings to the factory settings

SUrE? Confirmation inquiry

• Reset all menu settings to the factory settings with

• Do not reset the menu settings with

Page 44

Interface description

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

5 Interface description

5.1 SICS interface commands

The device supports the command set MT-SICS (METTLER TOLEDO Standard Interface Command Set). With SICS commands, it is possible to configure, query and operate

the scales from a PC. SICS commands are divided up into various levels.

5.1.1 Available SICS commands

In the case of Levels 0 and 1, these are commands which, if implemented, will function identically with all METTLER TOLEDO scales or weighing terminals.

In addition there are also further interface commands which apply either to the entire product series or to the particular application level. This and further information on the MT-SICS command set may be found in the MT-SICS Manual (Order Number 22 011 459 or at www.mt.com) or be obtained by request from your METTLER TOLEDO customer service representative.

Command Meaning

LEVEL 0 @ Reset the scale

I0 Inquiry of all available SICS commands

I1 Inquiry of SICS level and SICS versions

I2 Inquiry of scale data

I3 Inquiry of scale software version

I4 Inquiry of serial number

I6 Inquiry of weighing parameters

S Send stable weight value

SI Send weight value immediately

SIR Send weight value repeatedly

Z Zero the scale

ZI Zero immediately

LEVEL 1 D Write text into display

DW Weight display

K Keyboard check

SR Send and repeat stable weight value

TTare

TA Tare value

TAC Clear tare

TI Tare immediately

Page 45

Interface descriptionIND439check / IND439xx check / BBA439check

45User manual 22015307A 05/08

5.1.2 Requirements for communication between scale and PC

• The scale must be connected to the RS232, RS485, USB or Ethernet interface of a

PC with a suitable cable.

• The interface of the scale must be set to "Dialog" mode, see Section 4.6.1.

• A terminal progam must be available on the PC, e.g. HyperTerminal.

• The communication parameters baud rate and parity must be set in the terminal

program and on the scale to the same values, see Section 4.6.3.

5.1.3 Notes on network operation via the optional interface RS422/485

Up to 32 scales can be networked with the optional RS422/485 interface. In network operation, the scales must be addressed from the computer before commands can be sent and weighing results received.

Address Hex ASCII

00x300

10x311

20x322

... ... ...

90x399

10 0x3A :

11 0x3B ;

... ... ...

31 0x4F O

Description of the steps Host Direction Scale

1. Host addresses the scale, e.g. with the address 3A hex.

2. Host sends a SICS command, e.g. SI SI <CRLF> –––>

3. The scale confirms receipt of the command and sends the address back

<––– <ESC>:

4. The scale responds to the command and returns control of the bus to the host

<––– S_S____45.02_kg

<CRLF>

Page 46

Interface description

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

5.2 TOLEDO Continuous mode

5.2.1 TOLEDO Continuous commands

In TOLEDO Continuous mode the scale supports the following input commands:

5.2.2 Output format in TOLEDO Continuous mode

Weight values are always transferred in TOLEDO Continuous mode in the following format:

Command Meaning

P Printing out the current result

T Taring of the scale

Z Zero setting of the display

C Deleting of the current value

Status Field 1 Field 2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

STXSWASWBSWCMSD – – – –LSDMSD – – – –LSDCRCHK

Field 1 Field 2 STX SWA, SWB, SWC MSD LSD CR CHK

Cont-Wt: 6 digits for the weight value that is transferred without comma and unit Cont-Wt: 6 digits for the tare weight that is transferred without comma and unit ASCII character 02 hex, character for "start of text" Status words A, B, C, see below Most significant digit Least significant digit Carriage Return, ASCII character 0D hex Checksum (2-complement of the binary sum of the 7 lower bits of all the characters sent

beforehand incl. STX and CR)

Page 47

Interface descriptionIND439check / IND439xx check / BBA439check

47User manual 22015307A 05/08

Status word A

Status bit

Function Selection 6 5 4 3 2 1 0

Decimal position

X00 0 1 0 0 0

X0 0 0 1

X010

0.X 0 1 1

0.0X 1 0 0

0.00X 1 0 1

0.000X 1 1 0

0.0000X 1 1 1

Numerical increment

X1 0 1

X2 1 0

X5 1 1

Status word B Status word C

Function/Value

Function/Value Bit kg/lb g t oz Bit

Gross/Net: Net = 1 0 0 1 0 1 0

Sign: Negative = 1 1 0 0 1 1 1

Overload/Underload = 1 2 0 0 0 0 2

Movement = 1 3 Print request = 1 3

lb/kg: kg = 1 4 Extended = 1 4

151 5

Power up = 1 6 Tare manually, only kg = 1 6

Page 48

Interface description

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

5.3 MMR interface commands

The device supports the command set MMR (METTLER MultiRange). This command set is compatible to the weighing terminals ID1 and ID3. For new installations we recommend the SICS command set, refer to Section 5.1.

5.3.1 Available MMR commands

Command

Meaning

AR Read application block

AW Write application block

D Describe display

R0 Switch on the keyboard

R1 Switch off the keyboard

S Transmit stable weight value

SI Transmit weight value immediately

SIR Transmit weight value immediately and repeat

SR Transmit stable weight value and repeat

SX Transmit stable data record

SXI Transmit data record immediately

SXIR Transmit data record immediately and repeat

TTaring

U Switch over weight unit

Z Setting to zero

Page 49

Interface descriptionIND439check / IND439xx check / BBA439check

49User manual 22015307A 05/08

5.3.2 Syntax and formats

Commands have to be entered as ASCII characters and completed with C

RLF

The following ASCII characters are available: 20 hex/32 dec ... 7F hex/127 dec.

Command format when transmitting weight values

Response format when transmitting weight values

Example

Tare specification

command

T_13.295_kg

Tare specification

response

TBH_ _ _ _ _ 13.295_kg_

5.3.3 Error messages

Error messages consist of 2 characters and the delimiter C

RLF

Identification _ Weight value _ Unit Limit

String of characters for specification of command (1 ... 4 characters)

Blank 1 ... 8 digits,

Number of digits variable

Blank 1 ... 3 characters,

Number of characters variable

RLF

Identification _ Weight value _ Unit Limit

String of characters for specification of the response (2 ... 3 characters)

Blank 10 digits,

right-justified, fill with blanks

Blank 3 characters,

left-justified, fill with blanks

RLF

Error message

Meaning Description

ET Transmission error Error in the received bit sequence, e.g. parity

error, missing stop bit

ES Syntax error The received character string cannot be

processed, e.g. command does not exist

EL Logic error Command cannot be executed,

command is not supported on this application level

Page 50

Interface description

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

5.3.4 Available application blocks

The device disposes of the following application blocks. The numbers of application blocks that can be written are printed in bold.

No. Content

002 Current program number

003 <STX>

004 <ETX>

006 <CR><LF>

007 Gross, 2nd unit

008 Net, 2nd unit

009 Tare, 2nd unit

011 Gross, 1st unit

012 Net, 1st unit

013 Tare, 1st unit

014 Display contents

018 Difference

019 Percent

020 Setpoint – Upper tolerance – Lower tolerance – Starting point (current

values)

021 Start value

026 to 050

Setpoint – Upper tolerance – Lower tolerance – for memory 1 ... 25

Page 51

Event and error messagesIND439check / IND439xx check / BBA439check

51User manual 22015307A 05/08

6 Event and error messages

Error Cause Remedy

Display dark

• Back lighting set too dark ➜ Set back lighting (b.LIGHt)

brighter

• No mains voltage ➜ Check mains

• Unit switched off ➜ Switch on unit

• Mains cable not plugged in ➜ Plug in mains plug

• Brief fault ➜ Switch device off and back on

again

Insufficient load

• Load plate not on the scale ➜ Place load plate on the scale

➜ Set to zero

• Weighing range not reached

Overload

• Weighing range exceeded ➜ Unload scale

➜ Reduce preload

• Result not yet stable ➜

➜ If necessary, adjust vibration

adapter

• Function not permissible ➜ Unload scale and set to zero

• Zeroing not possible with over-

load or insufficient load

➜ Unload scale

• No calibration ➜ Unplug the mains plug then plug

it back in; switch unit off and then back on in battery mode

➜ Calibrate scale ➜ Call METTLER TOLEDO Service

• Impermissible target value or

impermissible tolerance

➜ Repeat input with permissible

values

• Printout not yet ended ➜ End printout

➜ Repeat required action

• No IDNet scale found ➜ Check connectors and cabling

➜ Call METTLER TOLEDO service

Page 52

Event and error messages

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

• Data communication with IDNet

scale faulty

➜ Remove and plug the power plug

back in. In case of battery operation switch the device off and on again

➜ Call METTLER TOLEDO service

• Restart error ➜ Remove and plug the power plug

back in. In case of battery operation switch the device off and on again

➜ Call METTLER TOLEDO service

• Weighing error ➜ Remove and plug the power plug

back in. In case of battery operation switch the device off and on again

➜ Call METTLER TOLEDO service

• EAROM checksum error ➜ Unplug the mains plug then plug

it back in; switch unit off and then back on in battery mode

➜ Call METTLER TOLEDO Service

Weight display unstable

• Restless installation location ➜ Adjust vibration adapter

• Draft ➜ Avoid drafts

• Contact between weighing pan

and/or weighing sample and surroundings

➜ Remedy contact

• Mains fault ➜ Check mains

Incorrect weight display

• Incorrect zeroing ➜ Unload scale, set to zero and

repeat weighing operation

• Incorrect tare value ➜ Clear tare

• Contact between weighing pan

and/or weighing sample and surroundings

➜ Remedy contact

• Scale tilted ➜ Level scale

Error Cause Remedy

Page 53

Technical data and accessoriesIND439check / IND439xx check / BBA439check

53User manual 22015307A 05/08

7 Technical data and accessories

7.1 Technical data

7.1.1 General data

IND439check / IND439xx check / BBA439check

Applications

• Weighing

• Check weighing

– Support through different colored background lighting of the display – Tolerance mode "Absolute", "Relative" and "Percentage" can be selected – Numerical specification of target values – 99 memory slots for target values – Fixed tolerances can be selected – Check weighing to zero

Settings

• Resolution can be selected

• Weighing unit can be selected: g, kg, oz, lb, t

• Taring function: Manual, automatic, next tare

• Automatic zero compensation mode during switching on and during operation

• Filter for adapting to the environmental conditions (vibration adapter)

• Filter for adapting to the weighing mode, e.g. dispensing (weighing process

adapter)

• Switch-off function, sleep mode for power-operated devices, energy saving mode

for storage battery operation

• Display illumination

• Graphics display of the weighing range

Display

• LCD liquid crystal display, digit height 21 mm, colored background lighting

Keyboard

• Tactile-touch membrane keypad

• Scratch-resistant labelling

Housing

• Stainless steel 1.4301 or AISI 304

• For dimensions, see Page 56

Page 54

Technical data and accessories

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

Net weight • IND439check/IND439xx check with

AC power supply unit

• IND439check/IND439xx check with

storage battery

• BBA439check-A with AC power

supply unit

• BBA439check-A with storage battery

• BBA439check-BB with AC power

supply unit

• BBA439check-BB with storage

battery

approx. 2.2 kg

approx. 2.8 kg

approx. 9.0 kg

approx. 9.6 kg

approx. 12.1 kg

approx. 12.7 kg

Protection type (DIN 40050)

• IP69K

Mains connection Direct connection to power supply (supply voltage fluctuation not exceeding ±10 %

of the rated voltage)

• IND439check weighing terminal:

Rated voltage 100 ... 240 VAC / 47 ... 63 Hz / 300 mA

• IND439xx check weighing terminal:

Rated voltage 230 VAC ±10 % / 47 ... 63 Hz / 300 mA

• BBA439check compact scale

Rated voltage 100 ... 240 VAC / 47 ... 63 Hz / 300 mA

Storage battery operation Supply at device: 24 VDC / 1.0 A

If the supply voltage is interrupted, the scale switches automatically over to storage battery operation

For operating life, see Section 7.1.2.

Ignition protection type IND439xx check (to IEC 60079-15)

• Hazardous area Zone 2:

Device category II 3G EEx nA II T4, Temperature range –10 °C ... +40 °C / 14 °F ... 104 °F

• Hazardous area Zone 22:

Device category II 3D IP66 T 70°C

IND439check / IND439xx check / BBA439check

Page 55

Technical data and accessoriesIND439check / IND439xx check / BBA439check

55User manual 22015307A 05/08

7.1.2 Operating life with storage battery

The operating life during storage battery operation differs depending on the intensity of use, the configuration and the connected scale.

The following approximate values apply with standard RS232 interface and a color setting with R+G+B=7:

Any additional optional equipment reduces the operating life correspondingly.

Ambient conditions

• Application

• Height

• Temperature range Class III

• Temperature range Class II

• Installation/overvoltage category

• Pollution degree

• Relative humidity

in interiors up to 2,000 m –10 ... +40 °C /14 ... 104 °F 0 ... +40 °C /32 ... 104 °F II 2 up to max. 80 %, non-condensing

Interfaces

• 1 RS232 interface integrated

• 1 further optional interface possible

Technical data for analog scales

For technical data of the analog scales to be connected to IND439check / IND439xx check please refer to the "IND4x9 / BBA4x9" installation instructions.

For technical data of the weighing platform used at BBA439check please refer to the PBA430 operating instructions.

IND439check / IND439xx check / BBA439check

Scale Conditions Duration

Scale with 1 DMS weighing cell (e.g. BBA439check)

10 % operating time 90 % power-off mode

120 h

Continuous operation 12 h

Scale with 4 DMS weighing cells 10% operating time

90% power-off mode

90 h

Continuous operation 9 h

K line 10% operating time

90% power-off mode

70 h

Continuous operation 7 h

Page 56

Technical data and accessories

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

7.1.3 IND439check / IND439xx check weighing terminal dimensions

Dimensions in mm

7.1.4 BBA439check compact scale dimensions

Dimensions in mm

289

180

129

189

188

Model A B C D E F

BBA439check-A... 300 102.5 235 240 175 380

BBA439check-BB 400 104.5 335 300 235 450

216

432

Page 57

Technical data and accessoriesIND439check / IND439xx check / BBA439check

57User manual 22015307A 05/08

7.1.5 Interface connections

The device can be equipped with a maximum of 2 communication interfaces. The following combinations are possible:

7.2 Accessories

COM1 COM2

Standard RS232 –

Standard + RS232 RS232 RS232

Standard + RS422/485 RS422/485 RS232

Standard + Ethernet RS232 Ethernet

Standard + USB RS232 USB

Standard + Digital I/O RS232 Digital I/O

Standard + WLAN RS232 WLAN

Designation Order number

GA46 thermal printer, RS232, 2.5 m cable and connector incl., not for a hazardous area

00 505 471

GA46 thermal printer, RS232, 0.4 m cable and connector incl., not for a hazardous area

00 507 229

GA46-W thermal printer, take-up device/protective hood, RS232, 2.5 m cable and connector incl., not for a hazardous area

00 505 799

GA46-W thermal printer, take-up device/protective hood, RS232, 0.4 m cable and connector incl., not for a hazardous area

00 507 230

Secondary display ADI419 (display without background lighting, stainless steel, IP69K, RS232, 3 m cable incl.), not for a hazardous area

22 013 962

Secondary display ADI419-B (display with background lighting, stainless steel, IP69K, RS232, 3 m cable incl.), not for a hazardous area

22 014 022

RS232 cable for SICS second scale (3 m, 8 pin <-> 9 pin Sub D connector)

22 006 795

RS232 cable for PC (3 m, 8 pin <-> 9 pin Sub D socket) 00 504 376

RS232 mating plug, 8 pin 00 503 756

RS422/RS485 cable (3 m, 6 pin <-> open ends) 00 204 933

RS422/RS485 mating plug, 6 pin 00 204 866

Ethernet 10/100 Base T twisted pair cable (5 m -> 8 pin RJ45) 00 205 247

Page 58

Technical data and accessories

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

Ethernet10/100 Base T twisted pair cable (20 m -> 8 pin RJ45)

00 208 152

USB adapter cable (0.2 m -> USB Series A socket) 22 006 268

USB adapter cable (3 m -> USB Series A socket) 22 007 713

Relay box for digital I/O option, not for a hazardous area

22 011 967

Connection cable Digital I/O option with relay box (10 m) 00 504 458

Digital I/O mating plug, 19 pin 00 504 461

Protective hood for IND4x9 terminals (set with 3 pieces) not for a hazardous area

22 013 963

Protective hood for BBA4x9 compact scales (set with 3 pieces) 22 013 992

Stand, stainless steel, for IND4x9 and PBA430, height 330 mm 22 013 964

Stand, stainless steel, for IND4x9 and PBA430, height 660 mm 22 013 965

Stand, stainless steel, for IND4x9 and KA, KB, MA, MB and DB weighing platforms

22 014 836

Bench stand, stainless steel, for IND4x9, suitable for mounting frame 503632 and 504854

22 014 835

Floor stand, stainless steel, for IND4x9 22 014 834

Stand base for floor stand 22 011 982

Wall adapter, stainless steel, for IND4x9, tiltable 22 013 966

Wall bracket, stainless steel, for IND4x9, rotatable and tiltable 22 014 833

GA46 mounting plate, stainless steel, for bench stand, floor stand and wall bracket

22 011 985

External storage battery for BBA4x9, stainless steel, IP69K (without charger)

22 013 988

Charger for version with internal or external storage battery (incl. power cable)

22 014 056

Designation Order number

Page 59

AppendixIND439check / IND439xx check / BBA439check

59User manual 22015307A 05/08

8 Appendix

8.1 Safety checks

The device has been tested by accredited inspection bodies. It has passed the safety checks listed below and carries the relevant test symbols. Production is subject to production monitoring by the inspection offices.

8.2 Tests for utilisation in hygienically sensitive areas

Weighing terminal IND439check and compact scale BBA439check have been assessed by the EHEDG (European Hygienic Engineering and Design Group) and the NSF (National Sanitation Foundation).

Both institutes certify the fulfilment of the hygienic requirements for easy cleaning (Hygienic Design Criteria).

EHEDG The EHEDG is an association of device manufacturers, firms in the foodstuff industry,

research institutes and health authorities. It was founded in 1989 with the aim of promoting the hygienically faultless manufacturing and packaging of foodstuffs. A positive expertise of the device by the EHEDG has taken place.

A corresponding report is available on the Internet under www.mt.com.

NSF NSF is an independent NGO founded in 1944 in the USA. Corresponding regulations

were published for the use of devices in the foodstuff industry. The device fulfils the NSF criteria C-2 (Special Equipment and/or Devices) for use in the foodstuff industry.

The corresponding certificate is available on the Internet under www.mt.com.

Country Test symbol Standard

Canada USA

CAN/CSA-C22.2 No. 1010.1-92 (für IND439check)

CAN/CSA-C22.2 No. 1010.1-04 (für BBA439check)

UL Std. No. 61010A-1

Other countries CB Scheme IEC/EN61010-1:2001

EU ATEX prototype test certificate only for IND439xx check:

EN 60079-15:2003 EN 50281-1-1:1998

CUS

Page 60

Appendix

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

8.3 Working to GMP (Good Manufacturing Practice)

Weighing terminal IND439check and compact scale BBA439check were evaluated by the Steinbeis-Transferinstitut Berlin with the following result:

"The device is excellently suited for GMP working to EC-GMP Guideline Annex 15 and PIC/S Guideline PI 006-1."

The evaluation encompasses the following points:

• Requirements for surfaces in the pharmaceutical production

• Ability to be cleaned

• Calibration

• Documentation with regard to qualification

The corresponding certificate is available on the Internet under www.mt.com.

8.4 Tables of geo values

For weighing instruments verified at the manufacturer’s, the geo value indicates the country or geographical zone for which the instrument is verified. The geo value set in the instrument (e.g."Geo 18") appears briefly after switch-on or is specified on a label.

Table GEO VALUES 3000e shows the geo values for European countries.

Table GEO VALUES 6000e/7500e shows the geo values for different gravitation zones.

8.4.1 GEO VALUES 3000e, OIML Class III (European Countries)

Geographical latitude Geo value Country

46°22' – 49°01' 18 Austria

49°30' – 51°30' 21 Belgium

41°41' – 44°13' 16 Bulgaria

42°24' – 46°32' 18 Croatia

48°34' – 51°03' 20 Czechia

54°34' – 57°45' 23 Denmark

57°30' – 59°40' 24 Estonia

59°48' – 64°00' 64°00' – 70°05'

25*

Finland

41°20' – 45°00' 45°00' – 51°00'

19*

France

47°00' – 55°00' 20 Germany

34°48' – 41°45' 15 Greece

45°45' – 48°35' 19 Hungary

Page 61

AppendixIND439check / IND439xx check / BBA439check

61User manual 22015307A 05/08

63°17' – 67°09' 26 Iceland

51°05' – 55°05' 22 Ireland

35°47' – 47°05' 17 Italy

55°30' – 58°04' 23 Latvia

47°03' – 47°14' 18 Liechtenstein

53°54' – 56°24' 22 Lithuiania

49°27' – 50°11' 20 Luxemburg

50°46' – 53°32' 21 Netherlands

57°57' – 64°00' 64°00' – 71°11'

24*

Norway

49°00' – 54°30' 21 Poland

36°58' – 42°10' 15 Portugal

43°37' – 48°15' 18 Romania

47°44' – 49°46' 19 Slovakia

45°26' – 46°35' 18 Slovenia

36°00' – 43°47' 15 Spain

55°20' – 62°00' 62°00' – 69°04'

24*

Sweden

45°49' – 47°49' 18 Switzerland

35°51' – 42°06' 16 Turkey

49°00' – 55°00' 55°00' – 62°00'

21*

United Kingdom

* factory setting

Geographical latitude Geo value Country

Page 62

Appendix

User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

8.4.2 GEO VALUES 6000e/7500e OIML Class III (Height ≤1000 m)

Geographical latitude Geo value

00°00' – 12°44' 5

05°46' – 17°10' 6

12°44' – 20°45' 7

17°10' – 23°54' 8

20°45' – 26°45' 9

23°54' – 29°25' 10

26°45' – 31°56' 11

29°25' – 34°21' 12

31°56' – 36°41' 13

34°21' – 38°58' 14

36°41' – 41°12' 15

38°58' – 43°26' 16

41°12' – 45°38' 17

43°26' – 47°51' 18

45°38' – 50°06' 19

47°51' – 52°22' 20

50°06' – 54°41' 21

52°22' – 57°04' 22

54°41' – 59°32' 23

57°04' – 62°09' 24

59°32' – 64°55' 25

62°09' – 67°57' 26

64°55' – 71°21' 27

67°57' – 75°24' 28

71°21' – 80°56' 29

75°24' – 90°00' 30

Page 63

AppendixIND439check / IND439xx check / BBA439check

63User manual 22015307A 05/08

8.5 FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to both Part 15 of the FCC Rules and the radio interference regulations ot the Canadian Department of Communications. These limits are designed to provide a reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the user manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Cet appareil a été testé et s’est avéré conforme aux limites prévues pour les appareils numériques de class A et à la partie 15 des règlements FCC et à la réglementation des radio-Interférences du Canadian Department of Communications. Ces limites sont destinées à fournir une protection adéquate contre les interférences néfastes lorsque l’appareil est utilisé dans un environnement commercial. Cet appareil génère, utilize et peut radier une énergie à fréquence radioélectrique; il est en outre susceptible d’engendrer des interférences avec les communications radio, s’il n’est pas installé et utilisé conformément aux instructions du mode d’emploi. L’utilisation de cet appareil dans les zones résidentielles peut causer interférences néfastes, auquel cas l’exploitant sera amené à prendre les dispositions utiles pour palier aux interférence à ses propres frais.

Page 64

Index

64 User manual 22015307A 05/08

IND439check / IND439xx check / BBA439check

9 Index

Access protection .................... 36

Accessories ............................ 57

Additional equipment ................. 8

Adjustment ............................. 31

Ambient conditions.................. 55

Analog scale .......................... 55

Applications ........................... 53

Calibration ............................. 31

Capacity utilisation .................. 17

Chain tare .............................. 16

Check weighing .......... 23, 24, 35

Cleaning ................................ 17

Compact scale.......................... 8

Continuous mode.................... 46

Device overview ........................ 9

Digital I/O......................... 41, 57

Dimensions ............................ 56

Display .................................. 10

Display accuracy .................... 31

Display precision .................... 33

Error messages....................... 51

Ethernet ................................. 57

Explosion protected weighing

terminals.................................. 5

External power supply ... 8, 14, 58

Filter ................................ 32, 34

Hygienically sensitive areas. 7, 17, 59

Ignition protection type............. 54

Info key.................................. 37

Interface commands

MMR................................ 48

Interface protocol .............. 46, 48

Interfaces

Configuring....................... 38

Connections ................. 8, 57

Keyboard................................11

Mains connection ........12, 13, 54

Application ........................ 35

Communication ................. 38

Diagnosis .........................43

Operation .......................... 25

Overview...........................27

Scale.......................... 31, 33

Terminal ........................... 37

Menu structure ........................ 26

Operator menu ........................ 25

Options ..................................41

Output options......................... 36

Password ...............................25

Power supply ....................12, 13

Protocol.................................. 17

Reset

Application ........................ 37

Interface............................ 40

Scale.......................... 32, 34

Terminal ........................... 38

RS232 ............................. 55, 57

RS422 ................................... 57

RS422/RS485.........................45

RS485 ................................... 57

Safety checks ..........................59

Safety instructions......................5

SICS commands......................44

Storage battery operation ....13, 55

Supervisor menu .....................25

Switching off ...........................15

Switching on ...........................15

Tare

Automatic ......................... 16

Chain tare......................... 16

Clearing ........................... 16

Target values

Specifying numerically ....... 21

Storing ............................. 21

Weighing in ...................... 19

Terminal settings ..................... 37

TOLEDO Continuous ................ 46

Tolerance settings.................... 35

USB ....................................... 57

Verification.............................. 14

Weighing terminal ..................... 8

Weighing unit ................... 31, 33

WLAN .............................. 41, 57

Zeroing................................... 15

Page 65

Page 66

*22015307A*

22015307A

Mettler-Toledo (Albstadt) GmbH

D-72458 Albstadt Tel. ++49-7431-14 0, Fax ++49-7431-14 232 Internet: http://www.mt.com