Page 1
• ECO Trend Insert
Installation Important information ..........2
Assembling your Metro.........................2-3
Floor protector requirements ...................4
Installing your Metro ................................4
Operation Important information ...........5
Where to install a Metro in your home ....6
Getting to know your Metro ....................6
Operating your Metro ..............................6
Cleaning and maintenance ...............7-8
Troubleshooting .......................................9
Metro warranty.......................................10
Replacement parts & accessories
...11-12
ECO Insert Models
Wood Fire Installation & Owner’s Operation Manual
PO Box 11, Inglewood 4347, New Zealand
Ph (06) 756 6520 • Fax (06) 756 6540
info@metrores.co.nz • www.metrores.co.nz
01/16 © PIONEER MANUFACTURING LTD
Page 2
2
This Metro wood re has been tested to and complies with
AS/NZS2918:2001 when installed in accordance with this
manual. Please ensure you are fully conversant with this relevant
standard and the contents of this manual. Correct installation is
critical to the safe operation and per formance of this wood re.
Please take particular note of the following:
• ECO Metro’s should be installed with a Metro ECO ue
system which has been developed to enhance the
performance of Metro wood res. A minimum length of 4.1
metres of 150mm diameter is required. Any alternative ue
system may invalidate the Metro’s emission approvals as
some councils within New Zealand have made installation
of Metro ECO ue systems with ECO Metros mandatory.
• The 150mm ue pipe must be fully encased to the
underneath of the ashing cone, from above the chimney
breast. (there must not be any 150mm ue pipe exposed).
• All ue joints must be sealed and riveted in three points
with stainless steel or monel rivets; the bottom of the ue
in particular MUST be fully sealed into the ue outlet of
the Metro wood re and secured with the bolt & nut as
supplied in the component kit.
• Ensure a breglass seal is placed between the outer
cabinet and the masonry to prevent air from within the
room being drawn into the chimney cavity.
• In New Zealand, the Metro Insert must be bolted securely to
the base of the chimney cavity to comply with the seismic
restraint provisions of AS/NZS2918.2001.
• The Metro fascia is coated in vitreous enamel. Take care
during assembly and when lifting or tting the fascia that
you do not damage this coating. Do not lift the Metro
fascia with your ngers under the louvre’s.
Fascia
Eco
Fireplace
Insert Firebox
Cabinet Top
Speed Clip (X4)
Insert Cabinet
Air Control
Knob
Handle
Door
Fixing Points
For Seismic
Restraint
Spacer Washer
Hinge Pin
Spindle
A
Diagram 1
B
• WE HIGHLY RECOMMEND YOU READ THIS ENTIRE
MANUAL AS INCORRECT OPERATION, MISUSE AND/OR
LACK OF MAINTENANCE WILL VOID THE WARRANTY
• The appliance and ue-system shall be installed in
accordance with AS/NZS2918 and the appropriate
requirements of the relevant building code or codes
• Any modication of the appliance that has not
been approved in writing by the testing authority is
considered to be in breach of the approval granted for
compliance with AS/NZS4013 and will void the warranty
•
The appliance must be installed correctly. We recommend
a competent and suitably qualied NZHHA installer
WARNING! Important Information
• Mixing of appliance or ue-system components
from different sources or modifying the dimensional
specication or components may result in hazardous
conditions. Where such action is considered, the
manufacturer should be consulted in the rst instance
• Do not install a Metro re if there is any sign of visible
damage to the product
• This appliance must be regularly maintained.
• Use authorised Metro replacement parts only. The use of
unauthorised parts may void the warranty
• This manual must be left with the home owner
CAUTION! Important Information
Assembling your Metro wood re
Page 3
3
All Metro Insert wood res are packed in two heavy-duty
cartons. The ECO Insert rebox is supplied in a heavy duty
palletised carton, this carton is clearly labelled. The fascia
and door are packaged inside a smaller separate carton. This
carton is also clearly labelled to show the colour and coating
nish of the fascia and door. Metro fascia’s are coated in
either vitreous enamel or stovebright high temperature paint.
Having removed the packaging and located this manual,
familiarise yourself with the illustrations on pages 2 & 3, and
proceed as detailed below.
Note: The Metro carton shows the model Metro you are about to install,
enabling you to select the appropriate model’s assembly instructions.
Metro ECO Insert
The ECO Insert rebox is supplied in a heavy duty carton and
is secured to a timber pallet. The carton is labelled to show
which model insert it is. Having removed the cardboard,
timber and polystyrene packaging and familiarised yourself
with Diagram 1 on page 2, proceed as follows: -
• Remove from within the rebox the plastic bag containing
the bolt kit, two rebricks wrapped in a cardboard wrapper
and the top bafe assembly.
• A “spacer” washer has been pre-tted and taped to the
top door hinge pin on the left hand side of the rebox
(Refer Inset A, Diagram 1) remove this tape.
• Take the boxed door you previously removed from the
centre of the fascia and unpack it. Taking the door in both
hands with the spindle end in your right hand and outer
face of the door facing you, attach the door to the rebox
as follows: -
- With the door in a 90 degrees open position, allow the
lower hinge pin on the bottom left hand side of the
rebox to pass into the hole provided in the bottom of
the door frame.
- Lift the door until the top of the door frame passes
over the top hinge pin, then align the hole provided on
the top face of the door frame and lower it down over
the top hinge pin.
- Take the door handle from the plastic bag and screw it
onto the door spindle by turning it clockwise.
• Unwrap the two rebricks from the cardboard wrapper and
t the side bricks to each side of the rebox. Location lugs
are tted to the base and rear of the rebox to retain the
side bricks in position, refer Diagram 2 this page.
• Remove the “cabinet top” which is packed inverted on top
of the rebox and t it into position “over” the cabinet sides
as detailed in Diagram 1. Ensure the rear edge is tted
correctly as shown Diagram 1, Inset “B”, the rear edge of
the cabinet top must t “into” the slot provided. Using two
of the self tapping screws from the plastic bag, secure the
cabinet top in place. Note, this panel can be tted at two
height’s. If the height of the replace opening will allow,
t the cabinet top in the higher position, t screws from
“inside” the cabinet facing out.
• Ensure the insulating blanket is in position on the top of the
cabinet.
• Remove the four speed clip nuts from the plastic bag
and t them to the holes provided in the front edge of the
cabinet as shown in Diagram 1.
ECO Insert Fan – In all clean air zones, the Metro ECO
Insert must be installed with Metro’s ECO Insert fan which
is a single speed, thermostatically controlled device. This
fan must be permanently wired and therefore requires the
services of a registered electrician. Fitting instructions for
the fan are supplied with the fan module.
Pre Installation
• Prior to installing your Metro replace insert into a replace
cavity, it is important that certain clearances and other
requirements are complied with as detailed below :-.
Fireplace Cavity
The chimney must be swept. Also: -
- Check for cracks and general overall condition. If repairs
are necessary, they must be carried out by a suitably
qualied person.
- Check the cavity dimensions to ensure the replace insert
will t. It is usually necessary to remove the re bricks from
the lower replace cavity.
- The base of the replace cavity on which the Metro
replace insert will rest must be level. If it is not, it should be
levelled using mortar.
- If an ash removal door exists in the base of the replace
cavity it should be sealed shut to prevent air entering the
cavity.
- If a timber or combustible mantelshelf exists above the
replace opening, it should be a minimum distance above
the top of the Metro’s fascia, minimum distance is 340mm.
If less than the above minimum specied, a deector or heat
shield will be required to be tted under the mantelshelf or to
the top of the fascia.
Front
top baffle
Rear top baffle
Side brick
Rear
support lugs
Diagram 2
Assembling your Metro wood re
Page 4
4
Metro replace inserts are designed to be installed directly
onto a concrete base. A non-insulating ash oor protector is
required to project in front of the Metro and must extend a
minimum of 200mm to each side of the door opening making
the minimum oor protector width 825mm. The minimum
oor protector projection forward of the Metro is 30 0mm as
illustrated right.
500mm
185mm
405mm
550mm
595mm
650mm
300mm
(CABINET WIDTH = 560mm)
Trend Fascia width = 810mm
Trad Fascia width = 805/874mm
Position the Metro ECO Insert which is still attached to its
wooden pallet directly in front of the replace cavity with the
rear of the insert facing the replace opening. The replace
insert assembly is bolted to the wooden pallet through its base
panel at two points being each front corner. Remove both
screws and slide the insert into the replace cavity taking care
not to mark the oor protector. Discard the pallet.
1. Attach the fascia with the four longer screws that were
supplied in the plastic bag, taking care that the air control
lever passes through the slot provided in the fascia.
Centralise and level the fascia on the replace insert door
and secure the four screws.
2. Applying pressure to the door or inside the replace rebox
(not the fascia) carefully manoeuvre the Metro until the
rear of the fascia is just touching the front face of the
replace surround. Taking care not to move the replace
insert, remove the fascia and mark the position of the
replace insert onto the replace base.
3. Using a masonry drill, drill into the chimney base through
the two slots which the replace insert was secured to
the pallet through. Check to ensure the replace insert
hasn’t moved and secure using suitable masonry anchors
to comply with the seismic restraint provisions of the
standard.
4. Remove the top bafe from inside the replace insert and
the removable cabinet top. Check that the ue stub of the
replace insert is in line by looking down the chimney, if not
a stainless steel offset or exi ue will be required.
5. Following the instruction sheet supplied with the ue
system, proceed and t the ue with all joints sealed and
riveted with a minimum of three stainless steel or monel
rivets on each joint.
6. With the ue pipe in position and sealed with a high
temperature re cement into the ue stub, drill through the
hole provided in the front of the ue stub into the stainless
steel ue pipe and secure with the 6mm bolt and nut
supplied in the plastic bag.
7. Ret the top bafe into the rebox’s upper chamber.
Reposition the removable cabinet top ensuring it is
correctly tting as detailed on page 2 and secure in its
upper position if possible. Note, if the adjustable height
top can be raised slightly but not fully to its upper position,
additional holes should be drilled to enable the top to be
raised to this level.
8. Using a suitable rated insulation (bretex 450 or similar)
pack any gap that exists between the sides and top of the
replace insert cabinet and replace surround.
9. If installing into a clean air zone, the Metro ECO Insert
must be installed with Metro’s ECO Insert fan as detailed
on page 3. Installation and wiring of this fan module
is necessary prior to tting the fascia, and full tting
instructions are supplied with the fan module.
10. Reattach the fascia, centralise and level with the door and
ensure the air control is moving freely and secure all four
screws.
11. Locate the air control knob which is included in the plastic
bag and carefully work it onto the air control lever.
The Metro is now fully installed and ready for operation but
it is preferable to defer lighting the re for a day or two if
possible to allow sealant used in the ue pipe joints to air dry.
Alternatively it is recommended you burn 2-3 sheets of loosely
crumpled newspaper at a time, approx once every hour over
a 6- 8 hour period.
Installation
Floor protector requirements
Page 5
5
This low-emission, slow combustion appliance is designed to
give you many years of warmth and service, subject to the
following key factors. These key factors, if not adhered to are
the major causes of unsafe installation, poor performance
and ue blockages and potential product failure.
1. Your Metro wood re must be installed correctly. Metro
recommend a competent and suitably qualied NZHHA
installer.
2. The only fuel to be used in this appliance shall be wood
that meets the following criteria.
– Less than 25% moisture content
– Has not been treated with preservatives or
impregnated with chemicals or glue,
– Is not chipboard, particle board, or laminated board,
– Is not painted, stained or oiled
– Is not driftwood or other salt impregnated wood
3. The appliance shall be operated at all times in
accordance with the “Installation and Operating
Instructions” supplied with each appliance.
4. It is preferable that Metro wood res should be installed
with a Metro ECO Flue System.
5. Coal must not be used as a fuel.
Please also note the following important points:
• In New Zealand a building consent is required from your
local building authority. The homeowner is responsible for
obtaining this consent.
•
As correct installation is critical to the performance and safe
operation of your Metro, it is recommended your Metro be
installed by a NZHHA registered installer or a person suitably
qualied in the installation of wood res. Your Metro retailer
will be able to arrange professional installation for you.
• During the very rst re your Metro will give off an odour
and fumes as the rebox paint cures. Do not be alarmed;
open all windows and externally opening doors in that
room and close any internally opening doors. This curing
process will last for approximately one hour and is likely to
happen this one time.
• Properly seasoned (dry) timber is necessary for the Metro
to operate efciently; rewood that contains a high
moisture content will result in ue pipe blockages, reduce
heat output and create other issues.
Note: Once split, Softwood usually takes 12 months to season - Hardwood
can take up to 24 months or more to season - Wood must be stored in a
location that enables air circulation. Unseasoned wood stored in a closed
woodshed without air circulation will still be unseasoned 12 months later.
• It is critical that the re not be operated with over worn,
faulty or missing door seals. Door seals will harden over
time and become over-worn (3-4 year’s) this will cause air
to leak into the re, causing the appliance to ‘over re’.
• It is critical that the re not be operated with over worn,
faulty or missing bricks, bafe plate, bafe extension
(white board on the bafe plate)
• It is critical that the re not be operated with cracked, or
broken door glass.
Please note, the above 3 points require regular inspection/
maintenance (every time the ash bed is cleaned out, generally
3-5 times a season) and if not maintained will void the rebox
warranty. A glowing rebox or lower uepipe is just one sign
you are over ring your appliance. Please ensure you keep your
proof of purchase/receipt on any parts you purchase.
• For optimum performance fuel must be loaded so the logs
lay “front to rear” in preference to laying across the width
of the rebox. Spaces should be left between the logs to
enable oxygen to get to as much of the surface of the fuel
as possible.
• A small hot re loaded frequently is more efcient than a
large re burning on a low setting.
• Your Metro is covered by a full unconditional 12 month
warranty on replacement parts, and a 10 year rebox
warranty.
• WE HIGHLY RECOMMEND YOU READ THIS ENTIRE
MANUAL AS INCORRECT OPERATION, MISUSE AND/OR
LACK OF MAINTENANCE WILL VOID THE WARRANTY
•
Any modication of the appliance that has not been
approved in writing by the testing authority is considered
as breaching AS/NZS 4013 and will void the warranty
• Do not use ammable liquids or aerosols in the vicinity
of this appliance when it is operating
• Do not dry clothes on or near this appliance
• Do not use ammable liquids or aerosols to start or
rekindle the re OR store fuel within the Metro’s specied
installation clearances
• Never operate your Metro with the door ajar, except on
initial start up
• Open the air control fully before opening the Metro’s door
WARNING! Important Information
• This appliance should be maintained & operated at all
times in accordance with this instruction manual
• This appliance should not be operated with cracked door
glass, over worn, faulty or missing door seals
• Do not use driftwood, treated or unseasoned (wet) fuel,
the use of most types of preservative treated wood as
fuel can be hazardous and will damage your appliance
• Burning unseasoned (wet) fuel or incorrect operation on
extended low burn cycles will cause excessive creosote
to form. Creosote is very corrosive and excessive
buildups will result in the ue pipe, ue spigot and upper
burn chamber failing. Failure of the applicance and/
or ue system due to creosote damage is not covered
under warranty. The formation of such is not an appliance
issue it is a fuel and operational issue
•
This appliance must be regularly maintained and
replacement parts must be authorised Metro parts only
• Do not empty ash into a combustible container
Congratulations on the purchase of your Metro wood re
CAUTION! Important Information
Page 6
6
Operating your Metro wood re is simple and you will quickly
learn how to get the best from it. First take a minute to
familiarise yourself with your new Metro:-
• Raise the door handle anticlockwise until the latch releases,
then slowly pull the door open. Load fuel and then close the
door ensuring the latch is secure. Never operate with the
door open or not latched securely.
• There is a single air control making your Metro easy to
adjust. This control moves from left to right, which is
“low to high”.
All Metro inserts have an air
control knob located directly
above and to the right of the
door. Slide this control knob
gently from right to left until
you reach a stop, this is a
preset “ low” position.
Metro insert air control
If your Metro has only been installed within the past few
days, the re cement seal at the base of the ue will not be
fully cured. To ensure the cement sets without blistering it
is recommended you burn 2-3 sheets of loosely crumpled
newspaper at a time, approximately once every hour over a
6- 8 hour period.
During the very rst re your Metro will give off an odour and
fumes as the rebox paint cures. Do not be alarmed. Open all
windows and externally opening doors in that room and close
any internally opening doors. This curing process will last for
approximately one hour and is likely to happen this one time.
Start up
Place a quantity of loosely crumpled newspaper on the base
of the rebox until it is approximately 50 % full of paper, or
place relighters on the base of the rebox. Add dry kindling
and move the air control knob fully to the right, being the “ full
open” position.
Light the paper at two or three locations across the front of
the door opening and leave the door slightly ajar resting
on the latch pin if necessary for a few minutes while the
re establishes. Once the kindling is burning well, open the
door and add 2-3 small logs at a time until you have a well-
established re. Usually this will take approximately 30 minutes,
during which time the air control should be set on “high” and
the door should be closed, except for the initial few minutes
and when fuel is being added.
Normal operation
Once the re is well established, regulate the air control to
achieve the desired burn rate and heat output. As you move
the air control to the right, burn rate, rebox temperature and
heat output will increase, if you move the control to the left
they will decrease.
Please note:
• Always open the air control fully prior to opening the door,
then open the door slowly.
• When loading logs, place them end-on, “front to back”; air
spaces should be left between the logs to enable oxygen
to get to as much of the surface of the fuel as possible.
• Every time you refuel, leave the air control on “high” for a
minimum of 20-25 minutes.
• Never use the door to force wood into the rebox, as this is
likely to break the glass.
• Always check the circulating fan starts once the rebox
heats up if operating in a clean air zone.
Wood res are usually installed in the main living area, which is
the section of the home that is usually kept the warmest, being
the area in the home most frequently occupied. However,
before deciding on the best location for your Metro wood re
you may wish to consider:
• Split level homes are best heated when the wood re is
installed on the lower level, as the heated air will rise to the
higher levels.
• Building construction is another consideration. Specied
clearances from walls, cur tains etc must be maintained
and you need to ensure no structural beams or internal
gutters etc are directly above your preferred site. If you
have a two storey dwelling you need to consider the
second storey to ensure you don’t have the ue directly
outside a second storey window.
Generally, you can install your Metro in your home anywhere
that suits you; Pioneer of fer various fan systems to transfer heat
to other sections of the home that are not heated sufciently.
It is necessary if using a fan system that the Metro you have
purchased has sufcient output to heat the total area you wish
to heat. Your Metro retailer or installer will be able to advise if
you are uncertain.
Where to install a Metro wood re in your home
Getting to know your Metro wood re
Operating your Metro wood re
Page 7
7
Cleaning and maintenance for your Metro wood re
Your Metro will give you many years of efcient service with
minimal maintenance if operated correctly using seasoned
fuel.
Metro fascia
The front panelling of your Metro Insert Fascia is vitreous enamel
coated. This can be cleaned with a damp cloth when the Metro
is not operating: -
• Vitreous enamel is extremely durable and designed to
last the life of the appliance. As vitreous enamel is glass, a
solid or heavy object dropped or banged against a panel
could chip the enamel surface.
• This appliance must be regularly maintained and
replacement parts must be authorised Metro parts only.
Door glass
Providing your fuel is properly seasoned, under normal
operating conditions the air-wash design of the Metro’s rebox
will keep the door glass clear. If the glass requires cleaning
you may use either a razor blade scraper or an oven cleaner.
If your door glass breaks it must be replaced with 5mm thick
ceramic glass which is available from your local Metro retailer.
Door seals
Over time, usually 3 -4 years, the door and glass seals will
become hard and cause air to leak into the rebox, causing
the appliance to ‘over re’. Your Metro retailer stocks
replacement woven breglass door and glass seals, which
need replacing when they become hard and over worn.
The door of your Metro is easily removed. Hold it in both hands
and lift the hinge end of the door up and over the top hinge
pin, then lower the door from the bottom hinge pin.
Side bricks
Hair-line cracks are not uncommon and are a result of
the intense heat within the Metro’s rebox, coupled with
mechanical damage caused by accidental impact when fuel
is being loaded. However if the side bricks become cracked to
the extent that they start to break up, they must be replaced.
Door adjustment
Provision is available on both sides of the door for adjustment.
To adjust the hinge end of the door, open the door fully, loosen
the top hinge nut and slightly lift the latch end of the door;
you will see the hinge assembly move back 1-2mm which
will usually be sufcient. Retighten, then repeat by loosening
the lower hinge nut, this time applying a slight downwards
pressure onto the door to move the lower hinge assembly
back a similar distance, then retighten.
The door latch is also adjustable, as the latch pin on the right
side of the rebox is t ted through a slot which enables the
latch pin to be loosened, moved back and re-tightened.
Ash removal
Over a period of time ash will build up in the base of the
Metro’s rebox and require removal. The time this build-up
takes depends on the density and cleanliness of your fuel.
To remove the excess ash your Metro should not be operating.
• Open the door, and using a hearth shovel or similar, empty
the excess ash directly into a steel or non-combustible
container.
• If the ash is not disposed of immediately, be careful where
you store it, as the ash can retain heat for many days and
become a re hazard.
• You must leave a bed of ash in the base of the rebox
approximately 10mm deep; this insulates the base of the
rebox and improves combustion.
Top bafe
Your Metro ECO Insert has a secondary burn chamber which
enables it to operate at very high efciency’s. This secondary
burn chamber is created by the top bafe which is illustrated
on the page 3 of this manual.
This is a ‘sacricial’ wear part of the rebox and should be
checked monthly. Usually only the “Promet ” (white board)
front/underneath section needs to be replaced when it starts
to disintegrate.
To remove and replace your Metro’s top bafe, proceed as
follows: -
• Open the Metro’s door fully, reach inside with the palm
of your hand face up and extended, lift the top bafe
approximately 20mm, then lift it forward out through the
door opening placing it on a sheet of newspaper you have
placed on the front of the hearth. Please Note: -
• Your Metro ECO Insert has a two part bafe as illustrated
on page 3. The rear bafe section also lifts “up and out”
the same as the front bafe.
• To ret the top bafe. Proceed in the reverse order and
note, the bafe must be tted so its rear is touching the
back of the rebox.
Note: Cracks in the promet are not uncommon and have no adverse
effect on the operation of your Metro. These cracks are the result of
intense heat coupled with expansion and contraction. Burning wood
which is not properly seasoned, i.e. 25% moisture content or more, will
over time cause the promet to disintegrate and require replacement.
Circulating Fan
In all clean air zones, the Metro ECO Insert must be tted with
Metros ECO Insert fan, This is a single speed, permanently wired
and thermostatically controlled device which runs continuously
once the rebox reaches operating temperature. This fan is
designed to run continually for many years without service, but
should be checked monthly to ensure it is operating.
If you are in any doubt regarding the fans operation, refer to
your Metro retailer or a registered electrician immediately.
Page 8
8
Flue systems
Should be checked annually, particularly the bottom end
of the lower ue section at its rear lock formed joint. If
deterioration is noticed contact your Metro retailer or installer.
The ue pipe should also be swept a minimum of once a year,
or as required during the winter season. If smoke enters the
room when you open the Metro’s door this usually indicates
the ue pipe is becoming restricted and needs cleaning. The
frequency of ue pipe cleans depends on many factors, with
the main variables being:
• The seasoning of the wood. If not properly seasoned you
will require frequent ue pipe cleans.
• The density of the wood. Softwoods generally result in more
deposits building up in the ue pipe.
To clean the ue pipe of your Metro, proceed as follows: -
• Open the Metro’s door fully, reach inside with the palm
of your hand face-up and extended, lift the top bafe
approximately 20mm, then lift it forward out through the
door opening, placing it on a sheet of newspaper you
have placed on the front of the oor protector.
Note: Some appliances have a two piece top baffle.
• Close the door and slide the air control to the left.
• Once on the roof, remove the cowl from the top of ue
system and sweep the ue pipe using a 150mm-diameter
ue pipe brush as detailed in the instructions provided with
the uebrush.
• Once the ue pipe is clear, clean and ret the cowl.
Remove the excess soot which has fallen into the rebox,
leaving a layer of ash 10mm deep on the base of the
rebox, then ret the top bafe.
Note: The baffle must be fitted so its rear is touching the back of the
firebox; if uncertain refer to page 3 in the installation section at the front
of this manual, which shows illustrations of the baffle location.
Cleaning and maintenance for your Metro wood re
Page 9
9
If your Metro is installed correctly, your fuel is dry and you
operate your re correctly, you will nd it to be a pleasure to
use. Metro’s many years of experience within the wood heating
industry has shown that dissatisfaction is mainly due to:
• unseasoned fuel
• faulty installation
• operational error
• or a combination of the above 3 points.
The following may be of assistance if you are experiencing any
of these problems.
SMOKE ENTERS THE ROOM WHEN THE METRO’S
DOOR IS AJAR (Possible reasons and solutions)
Check ue pipe joins:
If the ue pipe joins are not sealed correctly, the ue pipe will
not draw as well as it should. The ue pipe join connecting into
the ue spigot on top of the Metro is most critical, if this is not
sealed correctly, smoke will enter the room when the door is
ajar. To check this join is sealed correctly, run a match or lighter
ame around the join. If the ame is sucked into the spigot then
it is not sealed correctly. This check needs to be done when
the re is not going. Ensure you check the rear of the ue pipe/
spigot join, as due to the seam in the ue pipe, this is the most
common area for not being sealed correctly.
Ensure the fuel you are using is correctly seasoned:
If you are burning unseasoned fuel (wet), the re will cause
nothing but problems. The Metro won’t deliver much heat, it
will be lazy, smoke will enter the room when the door is ajar,
and the door glass will run black. Unseasoned fuel is the main
contributor to excessive creosote deposits which can be
corrosive to your appliance and ue system.
Flue pipe length is too short:
Add more ue pipe as the longer the ue system, the better the
draw of the ue pipe. Please note, if you did not purchase the
Metro ECO Flue System, you will not have the ECO Cowl which
increases draw. We highly recommend the Metro ECO Cowl is
tted as this will increase the draw. If you already have an ECO
Cowl and smoke is still entering the room, please add another
600mm length of ue pipe.
Downdraft:
If you have checked all of the above and the re is still smoking
into the room, it’s possible there may be a down draft issue.
Down draft is environmental and can be caused by many
variables, and it is purely trial and error to ascertain the cause.
Solutions may be:
• ‘H’ Cowl, designed purely for downdraft issues, but if you
have an ECO Cowl tted as standard, you will also need to
add another 600mm of ue pipe to compensate as the H
Cowl is shorter in length.
• Directional Cowl, designed for high wind areas.
Air control setting:
Ensure the air control setting is on high before opening the door
to reload, as this increases the draw up the ue pipe. Open the
door slowly.
If your Metro did not smoke, but its starting too and
is getting worse:
The ue pipe is in need of a clean. It is recommended that the
ue pipe be cleaned every season, however if you are burning
the re on low a lot, or are using unseasoned fuel, ue pipe
cleans will be required more frequently.
Correct operation:
Modern day wood res need to be operated hard and fast,
more so than low and lazy to ensure the rebox and ue
pipe runs hot and efciently. If the re and ue pipe is up to
temperature it will perform extremely well, the smoke will draw
up the ue pipe with ease, and the re will produce good
amounts of heat.
If the re is operated on low a lot of the time, the door glass will
run black, the ue pipe will tend to block up more frequently
and the re will end up smoking into the room when reloading.
It’s better to have a small re running hard and fast, rather than
a big re running low and lazy.
OTHER ISSUES YOU MAY EXPERIENCE
I can smell smoke in the room after a low burn cycle:
The smell is creosote that will be seeping through the ue
pipe join or out of the ue spigot onto an external sur face,
thus creating the smell in your room. The cause will be either
unseasoned fuel, fuel mass too large, incorrect operation on
low burn cycles or a combination. Creosote is very corrosive
and excessive buildups will result in the ue pipe and potentially
the ue spigot and upper burn chamber failing. The formation
of excessive creosote is not an appliance issue, it is a fuel and
operational issue. Failure of ue pipe or rebox due to creosote
build up is not covered under warranty as excessive creosote
build up is only possible from either unseasoned fuel or incorrect
operation.
The Metro won’t turn down as much as it did
The door itself may need readjusting, the hinge and latch is
slotted and allows for movement. Loosening the hinge and
moving it back a few mm will make the door seal tighter and
stop air leaking into the re. The door and glass seals may be in
need of replacing, which is generally required every 3-4 years.
Familiarise yourself with the instructions on page 8 before
proceeding with this maintenance.
Troubleshooting your Metro wood re
Page 10
10
Metro wood res are manufactured in New Zealand, using
the highest quality of materials, workmanship and the latest
manufacturing techniques, which is why we offer a full 10 year
rebox warranty and 1 year par ts warranty for peace of mind.
METRO WARRANTY
(NZ Consumer laws apply to this warranty)
Pioneer Manufacturing Limited (Pioneer) warrants the steel
rebox against defective materials and workmanship which
would render it un t for normal domestic use, from the date of
purchase by the original consumer, for a period of 10 years.
Components including panel coating, door retainers, door
seals, glass, trim, baf e & bricks are warranted for a period of
1 year from the date of original purchase for normal domestic
use against defective materials and workmanship.
All associated accessories including, but not limited to, fans,
ue systems, ue shields, wetbacks, tool sets, ash pots etc, are
covered by a 1 year warranty against defective materials and
workmanship.
It is recommended, but not a condition of this warranty, that a
full service/inspection of the Metro wood re be carried out at
the end of each winter season.
Warranty Conditions:
• The Metro wood re must be installed, operated and
maintained strictly in accordance with the building code
and this installation and operation manual.
• The Metro wood re must be installed and used in a
domestic application.
• This warranty covers appliance like for like replacement or
repair at the manufacturer’s discretion but excludes freight,
travel, installation, labour and/or any other associated costs.
• Pioneer or their agents are not liable for any loss or expense
direct or indirect arising from the failure of any part or
operation of the appliance.
• Operation of this appliance in violation of the warnings in this
operation and installation manual will void this warranty.
• Your Metro wood re must be regularly maintained and we
recommended it is also serviced annually. Proof of servicing
may be required. If a wood re is not regularly maintained
and serviced, the life span will be reduced. If your Metro
wood re has been neglected, by not being regularly
maintained and serviced, warranty may be declined.
• It is critical that the re not be operated with over worn, faulty
or missing door seals. Door seals will harden over time and
become over-worn (3-4 year’s) this will cause air to leak into
the re, causing the appliance to ‘over re’.
• It is critical that the re not be operated with over worn,
faulty or missing bricks, baf e plate or baf e extension (white
board on or under the baf e plate)
• It is critical that the re not be operated with cracked, or
broken door glass.
•
A claim under this warranty should be directed to the retailer
who supplied the Metro wood re. If this is not possible write
directly to the manufacturer stating details of fault, model
and serial number of your Metro, date and proof of purchase
and name of retailer where the Metro was purchased.
Warranty Exclusions:
This manufacturer’s warranty does not cover:
• Service calls which are not related to any defect in the
product (i.e. operational, installation or fuel issues). The
cost of a service call will be charged if the problem is not
found to be a product fault.
• Defects caused by factors other than normal domestic use
or use in accordance with the product ’s operation manual.
• Defects caused through the product being operated in
an “over- red” manner resulting in sections of the rebox
operating excessively hot to the point that sections glow
red. (Note – This will result in distortion of the rebox)
• Defects to the product caused by accident, neglect, misuse
or act of God.
• The cost of repairs carried out by non-authorised repairers
or the cost of correcting such unauthorised repairs.
• Required maintenance as set out in this manual.
Service under this manufacturer’s warranty must be provided
by a repairer authorised by Pioneer Manufacturing Ltd. Such
service shall be provided during normal business hours.
Purchase Date
Serial Number
Model
Colour
Retailer
IMPORTANT! Complete and retain these details at time of purchase:
Warranty details for your Metro wood re
Note: The above 3 points require regular inspection/
maintenance (every time the ash bed is cleaned out,
generally 3-5 times a season) and if not maintained will
void the rebox warranty. Please ensure you keep your
proof of purchase/receipt on any parts you buy.
IMPORTANT INFORMATION
Page 11
11
Parts guide for your Metro – Bafe, promet and wetback
Listed below are the parts and product codes for your Metro
wood re. The promet/bafe should be regularly checked and
must always be in place during the operation of your re.
Note: Cracks in the promet are not uncommon and have no adverse
effect on the operation of your Metro. These cracks are the result of
intense heat coupled with expansion and contraction and is normal
wear & tear.
Your Metro wood re must be regularly maintained and we
recommended it is also serviced annually. If a wood re is
not regularly maintained and serviced, the life span will be
reduced. If your Metro wood re has been neglected, by not
being regularly maintained and serviced, with authorised
Metro parts replaced as required, your warranty may be
declined.
Clean air model
Type of promet required / Type of steel bafe(s) required Water heating options
• ECO Trend Insert
ECO Small Promet 500-1650 ECO Insert Front 500-2250 ECO/LTD Insert Rear 500-2300
No wetback if this fire is
installed in a clean air zone.
The 3kW or 4kW Wetback can be
fitted in a non-clean air zone.
3kW Wetback 450-0100 or
4kW Wetback 450-0150
420mm
110mm
420mm
125mm
420mm
220mm
Metro - Visit us online today www.metrores.co.nz
Metro Wood Fire Specications
Metro have a Specications Brochure available which details
relevant compliance data for every model. This brochure is
updated annually and details the minimum clearances and
specications for all models, which is generally required when
applying for a building consent. See your Metro retailer to
obtain a copy, or visit www.metrores.co.nz
metrores.co.nz
Visit the Metro website: www.metrores.co.nz to view Metro’s
‘video demos’ showing the latest in wood re technology energy
saving options. You can view the entire Metro product range,
nd out where your nearest Metro retailer is located or simply
check out the latest specications, installation requirements
and emission and efciency data for the Metro of your choice.
Page 12
12
Metro Accessories
Metro offer a range of heating accessories designed to
compliment your Metro wood re. See below for some of the
products within our heating accessory range.
This range of accessories includes oor protectors, heat transfer
systems, child guards, baf es, bricks and more. For further
details ask your Metro retailer for a copy of the Metro heating
accessories brochure, or visit www.metro res.co.nz
ECO Flue Systems
Child Guards
Corner and Wall Floor Protectors
Flashrites and Versatiles
Heat Transfer Systems
Glass Tape
Wetbacks
Universal Door Seal Kits
Door Seal Rope
High Temperature Paint
Fire Cement And Silicone
Chubb Smoke Detectors
Pioneer heating accessories
Loading...