Page 1
Item# _______________________________________________
Job _________________________________________________
Racks Single Section/Model RT Series
InterMetro Industries Corporation
North Washington Street
Wilkes-Barre, PA 18705
www.metro.com
Copyright © 1993 InterMetro Industries Corporation
13.72
Metro Mobile
SIDE LOAD
“KNOCK DOWN” RACKS
• Material: Special design, natural finish, highstrength, extruded aluminum (6063-T6 alloy).
• Rugged: Tubular framework with aircraft-riveted
slide assemblies.
• Economical: Shipped “knocked down” for
reduced freight rate. Easily assembled with 12
bolts.
• Sanitary: Removable slide assemblies for easy
cleaning.
• Versatile: Slide assemblies can be replaced
with slides of other than standard spacing while
retaining the same framework.
• Pass-Thru Design: Can be loaded on one side
and unloaded from the other for maximum
efficiency and convenience.
• Stable: 5” (127mm) diameter, NSF-listed
casters, corner-mounted for maximum stability.
• Lightweight: Easy to handle.
• Rapid Cooling
Note: Available factory set-up. See price list.
Copyright © 2000 Metropolitan Wire Corp.
RT3511N
Page 2
Job____________________________________________
Metro Mobile
SIDE LOAD “KNOCK DOWN” RACKS
Manufactured by:
InterMetro Industries Corporation
North Washington Street, Wilkes-Barre, PA 18705
Phone: 570-825-2741 • Fax: 570-825-2852
For Product Information Call: 1-800-433-2232
Visit Our Web Site: www.metro.com
Racks Single Section/Model RT Series
13.72
Specifications
• Material: Special design,
natural finish, high-strength,
extruded aluminum (6063-T6
alloy).
• Construction: Pass-thru
design, aircraft-riveted
construction on slide
assemblies, tensilok fasteners
for frame assembly.
• End Frames: 1” (25mm)
square x .093” (2.4mm) wall
extruded aluminum tubing.
• Tie Bars: Left to right and
front to back tie bars of 1”
(25mm) diameter aluminum
bar stock, drilled and tapped
at each end.
• Slides, 3” (76mm) & 5”
(127mm) Spacing: .060” x
11/4” x 11/2” (1.5 x 32 x 38mm)
profile, bulb-tipped extruded
angle-riveted to .060” x 1” x 1”
(1.5 x 25 x 25mm) angle
uprights.
• Slides, 11/2” (38mm)
Spacing: .060” x 1/2” x 11/2”
(1.5 x 13 x 38mm) profile,
bulb-tipped extruded channelriveted to .060” x 1” x 1” (1.5 x
25 x 25mm) angle uprights.
• Casters: Two HS5M on back
— 5” (127mm) diameter ball
bearing swivel stem casters
with self-lubricating axle. Two
HS5MB on front — same as
above with wheel brake. NSF
listed.
DIMENSIONS:
(a) (b) (c) (d) Shipping
Height Width Depth Inside Height Slide Spacing Pan Capacity Weight
Model No. (in.) (mm) (in.) (mm) (in.) (mm) (in.) (mm) (in.) (mm) no. size (in.) (lbs.) (kg)
RT3318N 641/81630 283/8720 183/4475 561/21435 3 76 18 18 x 26 40 18
RT3511N 641/81630 283/8720 183/4475 561/21435 5 127 11 18 x 26 38 17
ACCESSORIES:
Model
__________________________________________
SU Factory Set-Up
__________________________________________
A38 Gray Rubber Corner Bumpers
__________________________________________
L02-082
Rev. 12/00 BJ
Printed in U.S.A.
Information and specifications are subject to change
without notice. Please confirm at time of order.
Loading...