Page 1
Item# _______________________________________________
Job _________________________________________________
Wine Storage Systems Components & Accessories
InterMetro Industries Corporation
North Washington Street
Wilkes-Barre, PA 18705
www.metro.com
10.49
SUPER ERECTA SHELF
®
WINE SHELVING COMPONENTS
• Although the standard units offered in both types of wine shelving will meet a
large range of wine storage needs, there will be instances where it is
advantageous to order this shelving by components.
Often it is possible to make more efficient utilization of storage space or to
provide for special storage needs by using components to create a different
configuration than a standard unit. At other times cost savings can be effected by
eliminating unneeded components of the standard units, such as reducing the
number of bin dividers and bottle supports when part of the unit will be used for
storage in cartons or ordering fewer end or back panels if units are to be placed
end-to-end or back-to-back.
Basic Components
• Posts with Foot Plate: Order Four. All posts are fitted with triangular foot plates
which bolt the units to the floor for greater stability.
DIMENSIONS:
Overall Approx.
Height Pkd. Wt. Ea.
Cat. No. (in.) (lbs.)
74FPC 743/
4
4.5
86FPC 863/
4
5.5
14" Cradle Shelves
Approx.
Width Length Pkd. Wt. Capacity
Cat. No. (in.) (in.) (lbs.) (750ml bottles)
W1436NC 14 36 7 9
W1448NC 14 48 8.5 12
14" Flat Wire Shelves
Approx.
Width Length Pkd. Wt.
Cat. No. (in.) (in.) (lbs.)
1436NC 14 36 9.5
1448NC 14 48 12
Copyright © 2000 InterMetro Industries Corp.
Cradle Shelf
Page 2
Job____________________________________________
SUPER ERECTA SHELF
®
WINE SHELVING COMPONENTS
Manufactured by:
InterMetro Industries Corporation
North Washington Street, Wilkes-Barre, PA 18705
Phone: 570-825-2741 • Fax: 570-825-2852
For Product Information Call: 1-800-433-2232
Visit Our Web Site: www.metro.com
Wine Storage Systems Components & Accessories
10.49
Enclosure Components
End Panels*
• Order two per unit, except that
when units are placed end-toend only one panel is needed
between each pair of units.
End Panels
Back Panels
Approx.
Width Height Pkd. Wt. Use With
Cat. No. (in.) (in.) (lbs.) Posts
EP27C 13 60 11 74FPC
EP28C 13 75 13 86FPC
Back Panels*
• Order two per 36” long unit;
order three per 48” long unit.
(None needed if units are
placed against wall. Only one
set needed if two units are
placed back-to-back.)
Wall Clamps
• To give single units greater stability, two clamps hook under the top shelf and
can be secured with fasteners suitable to the wall.
Cat. No 9984C
Approx.
Width Height Pkd. Wt. Use With
Cat. No. (in.) (in.) (lbs.) Posts
BP27C 141/
2
60 11 74FPC
BP28C 141/
2
75 13 86FPC
*For end and back panels to fit properly, there must be a shelf spaced
every 15 inches as in the standard 15” spacing for bin racks and 5”
spacing for cradle shelving.
Bin Components for Bulk Storage Units
Bin Dividers
• Use on 1436NC or 1448NC
shelves spaced 15” apart. For
standard positioning, use
template #C5-077.
Approx.
Width Height Pkd. Wt.
Cat. No. (in.) (in.) (lbs.)
BD15C 121/
2
19 2
Bottle Supports
• For use on 1436NC and
1448NC shelves when bottles
are to be stacked in bins.
Approx.
Length Pkd. Wt. Use on
Cat. No. (in.) (lbs.) Shelf Length
BS3C 35 2 36”
BS5C 47 2 48”
Door Set
Door Set (Fits only WB257C
and WC257C)
Approx.
Width Height Pkd. Wt.
Cat. No. (in.) (in.) (lbs.) Fits Units
ED57C 51 60 42 48” long x 743/4” high
Two end panels must be used in order to assemble door set.
Bottle Support
Joining Hook
Wall
Clamp
Accessories for Bulk and Cradle Storage Units
Joining Hook
• Used when units are placed
back-to-back or end-to-end.
Width Depth Height
Cat. No. (in.) (in.) (in.)
JH2C
21
/
32
15/
8
21/
4
14” Wall Mounts
• Both types of wine shelves can be wall-mounted. See sheet #10.40 for 14”
direct and post-type wall mounts.
Label Holders
• See sheet 10.06 for a complete selection.
Bin Divider
L02-026
Rev. 12/00 BJ
Printed in U.S.A.
Information and specifications are subject to change
without notice. Please confirm at time of order.
Loading...