Page 1
Item # ______________________________________________
REGULAR ERECTA SHELF
Item # ______________________________________________
Job ________________________________________________
Job ________________________________________________
®
SHELVING ACCESSORIES
Shelving Accessories
REGULAR ERECTA SHELF
• Wall Mounts: Used to create wall-mounted shelving units
with 12" or 18" (305 or 460mm) regular Erecta Shelf
shelves of any length. Models are available to
accommodate from one to five shelves. Each mount
consists of shelf support and mounting brackets. Wall
bolts or screws not included; they must be selected
according to type of wall. Order shelves from sheet
#10.50.
Dimensions:
(in.) (mm) (in.) (mm) Capacity Chrome (lbs.) (kg)
12 305 103/4273 1 shelf 12WB1C 21/21
12 305 2013/16529 1 to 3 shelves 12WB3C 5 2
12 305 3013/16783 1 to 5 shelves 12WB5C 71/431/
18 460 113/4298 1 shelf 18WB1C 3 11/
18 460 215/8549 1 to 3 shelves 18WB3C 6 23/
18 460 315/8803 1 to 5 shelves 18WB5C 81/24
For additional mounting brackets (single) order. Model No. 9975C
Double mounting brackets are also available for use where continuous wall
shelving is to be installed. Model No. 9976C
®
Approx. Pkd.
).rP( .tWModel No.thgieHhtdiW
4
2
4
®
• Wall Kit: Kit includes two shelves, shelf supports, and
mounting brackets. Wall bolts and screws not included;
they must be selected according to type of wall.
Shelf Overall Shelf Overall Overall Approx.
Model No. (in.) (mm) (in.) (mm) (in.) (mm) (in.) (mm) (in.) (mm) (lbs.) (kg)
12WS12C 24 610 261/
12WS32C 36 910 381/
12WS52C 48 1220 501/
Kit packaged in one box and UPS shippable.
Length Length Width Width Height Pkd. Wt.
670 12 305 13 330 21 530 181/281/
4
970 12 305 13 330 21 530 251/4111/
4
1275 12 305 13 330 21 530 32 14 3/
4
InterMetro Industries Corporation
North Washington Street
Wilkes-Barre, PA 18705
www.metro.com
2
2
4
10.56
Page 2
REGULAR ERECTA SHELF
SHELVING ACCESSORIES
• 1" (25mm) Shelf Ledges: To prevent items from
protruding or falling off shelves, ledges can be
installed on the shelf edges.
In many cases a one-inch (25mm) ledge will serve
the purpose, while allowing access to the shelf from
all sides. When a higher ledge is needed, the fourinch (100mm) size can be used on the back or front
of the shelf.
For enclosure of the entire back of a shelving unit,
rods and tabs (below) can be attached.
®
1" (25mm) Ledge)
Dimenions:
1" (25mm) Back Ledges
Length Model No. Per
(in.) (mm) Chrome (lbs.) (kg)
24 610 L24N-1C 6 23/
30 760 L30N-1C 12 51/
36 910 L36N-1C 15 7
42 1060 L42N-1C 161/
48 1220 L48N-1C 21 91/
60 1525 L60N-1C 221/
• Rods & Tabs: Rods hook over wires of top shelf and
are attached to each of the other shelves with
spring-clip tab. Each rod requires one tab for each
shelf except top self. Chrome.
Approx.
Pkd. Wt.
1
/2Doz.
2
2
4
2
7
2
10
Dimensions:
Rods
Height Rod Length Pkd. Wt.
(in.) (mm) (in.) (mm) Model No. (lbs.) (kg)
531/
631/
731/
881/
1360 52 1320 R52C 1
2
1610 61 1550 R61C 1
2
1870 72 1830 R72C 11/
2
2250 86 2185 R86C 11/
2
.xorppAthgirpU
1
/
1
/
1
/
4
3
/
2
2
2
2
4
Tabs
Rods are shipped with sufficient tabs for a 4-shelf
unit. For additional tabs order:
Wire Shelf Tab Model No. 9084Z
Page 3
REGULAR ERECTA SHELF
SHELVING ACCESSORIES
®
• 8" (203mm) Shelf Dividers: Shelf dividers enable you to
compartmentalize shelves, help keep shelf contents orderly.
Because they snap into place, they can be positioned and
repositioned to exact size of section needed. All models 8"
(203mm) high.
Approx.
Shelf Width Model No. Per 1/2Doz.
(in.) (mm) Chrome (lbs.) (kg)
12 305 DD12C 12 51/
18 460 DD18C 131/26
24 610 DD24C 161/271/
Rods and tabs can serve a similar purpose when entire unit is to be
compartmentalized.
Pkd. Wt.
2
2
Page 4
Job ________________________________________________Job ________________________________________________
10.56
REGULAR ERECTA SHELF
SHELVING ACCESSORIES
• Shelf Spacers: Where shelves are wanted at spacing other than 5"
(127mm) increments, shelf spacers wedge into the upright channels to
provide a solid support at the desired level. Spacers are used at outside
corners, four per shelf.
Spacer 9988Z
®
Model No.
• Corner Brace: When regular Erecta Shelf
units are to be joined at right angles, corner
braces link shelf ends of one unit to shelf
sides of the other, eliminating one upright
and leaving the shelving corner open and
fully usable. Two required per shelf.
Model No. 9999Z
®
• Upright Clamp: Where regular Erecta
®
Shelf
units are to be joined end-to-end,
the upright clamp holds the adjacent
uprights securely so that each unit
buttresses the other.
Model No. 9971Z
• Foot Plate: Replaces the leveling bolt.
Used when units are to be bolted to the
floor or, without bolts, when a broader foot
is desired.
Model No. 9993Z
SHELF
®
REGULAR ERECTA
Shelving Accessories
All Metro Catalog Sheets are available on our Web Site: www.metro.com
InterMetro Industries Corporation
North Washington Street, Wilkes-Barre, PA 18705
Phone: 570-825-2741 • Fax: 570-825-2852
For Product Information Call: 1-800-992-1776
Printed in U.S.A. Rev. 10/10
Information and specifications are subject to change
without notice. Please confirm at time of order.
Copyright © 2010 InterMetro Industries Corp.
L02-029
Loading...