Metra Electronics 99-6537B, 99-6536, Jeep Grand Cherokee 2014-up Installation Manual
INSTALLATION INSTRUCTIONS FOR PART 99-6537B
METRA – The World’s best kits.
®
CAUTION!
All accessories, switches, climate controls panels,
and especially air bag indicator lights must be connected before
cycling the ignition. Also, do not remove the factory radio with
the key in the on position, or while the vehicle is running.
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted Black
• Touchscreen display for climate and
personalization features
• A) Radio trim panel with touchscreen display • B) Radio brackets • C) Pocket
• D) (4) #8 x 3/8” Phillips screws • E) (6) Panel clips • F) HVAC interface and wiring harness (not shown)
KIT FEATURES
KIT COMPONENTS
• Panel removal tool • Phillips screwdriver
• 9/32” socket wrench • 5.5mm socket wrench
TOOLS REQUIRED
Dodge Durango 2014-up
99-6537B
Table of Contents
A B C D
E
Dash Disassembly ................................................. 2
Kit Preparation ....................................................... 2
Kit Assembly
– ISO DIN radio provision with pocket ...................... 3
– ISO DDIN radio provision ...................................... 3
Axxess Interface Installation ...........................4-13
WIRING & ANTENNA CONNECTIONS
Wiring Harness: Axxess interface and harness included Antenna Adapter: 40-EU55 (sold separately)
99-6537B
2
Dash Disassembly
1. Unclip and remove the radio/
climate control panel. (Figure A)
2. Remove the (4) 9/32 screws
securing the radio/display screen,
and then unplug and remove.
3. Remove the (3) 5.5mm screws
securing the black control module
in the sub-dash, and then relocate
lower to allow clearance for the
aftermarket radio.
Continue to Kit Preparation
(Figure A)
(Figure A)
To the 99-6537CH radio trim panel:
1. Attach the (6) panel clips provided.
(Figure A)
Continue to Kit Assembly
Kit Preparation
99-6537B
3
Kit Assembly
(Figure A)
(Figure B)
(Figure A)
ISO DIN radio provision with pocket
1. Attach the pocket to the radio
brackets using the (4) #8 x 3/8”
Phillips truss-head screws provided.
(Figure A)
2. Remove the metal DIN sleeve and
trim ring from the aftermarket radio.
3. Slide the radio into the bracket/
pocket assembly, and then secure it
using the screws supplied with the
radio. (Figure B)
Continue to Axxess
Interface Installation
ISO DDIN radio provision
1. Attach the brackets to the radio
using the screws supplied with
the radio. (Figure A)
Continue to Axxess
Interface Installation
99-6537B
4
Axxess Interface Installation
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, speed sense)
• Retains audio controls on the steering wheel
• Retains safety chimes
• Retains the factory backup camera
• Retains the factory AUX-IN jack
• Retains balance and fade*
• Micro “B” USB updatable
* Non-amplified models only.
INTERFACE FEATURES
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
TOOLS REQUIRED
• Axxess interface (built into the touchscreen display)
• 6537 harness
• 16-pin harness with stripped leads
• 4-pin harness with yellow RCA jacks
• Hazard harness
• Female 3.5mm connector with stripped leads
Connections to be made .......................................................................... 5-7
Installing the interface ............................................................................... 8
Initializing the interface ............................................................................. 8
Final assembly ............................................................................................ 8
Touchscreen display operation .............................................................9-11
Steering wheel control settings .......................................................... 12-13
INTERFACE COMPONENTS
TABLE OF CONTENTS
Loading...