Metra Electronics 99-3400, AW-407GO, DW-3400 Installation Manual
KIT COMPONENTS
Radio Housing
Spacer
Bracket
Set #1
Bracket
Set #2
(6) #6 Phillips Screws
(4) #8 Phillips Screws
(4) Speed Clips
(2) Phillips
Screws
Equalizer
Dummy Plate
5 6
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
Re-connect the battery terminal and test the unit
for proper operation. Mount the radio/kit
assembly to the sub-dash with those screws
previously removed in step #1.
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
7
ALL VEHICLES
2-SHAFT HEAD UNITS: Attach the Spacer* to the Radio Housing. Slide the aftermarket
head unit into the kit and secure with shaft nuts. (see Fig. A)
DIN HEAD UNITS: Cut and remove the shaft supports from the Spacer* and Radio Housing.
Slide the DIN cage into the kit and secure by bending the metal locking tabs down. Slide the
aftermarket head unit into the cage until secure. (see Fig. B)
(If an equalizer will be included, slide the unit into the back of the Radio Housing and secure.
If an equalizer will NOT be included, snap the Equalizer Dummy Plate into the opening).
4
Fig. A
Fig. B
99-3400
AW-407GO
DW-3400
INSTALLATION
INSTRUCTIONS
TOOLS REQUIRED
Cutting tool
Phillips screwdriver
APPLICATIONS
CAR PAGE
CHEVROLET
Spectrum 1985-89.........................................................................1
GEO
Prizm 1989-92..............................................................................2
Spectrum 1989..............................................................................1
Storm 1990-93 (NOT keeping the factory pocket)...........................3
Storm 1990-93 (keeping the factory pocket).................................. 4
HONDA
Passport 1994-95..........................................................................5
ISUZU
Amigo 1991-94.............................................................................5
I-Mark 1985-91............................................................................ 6
Impulse 1990-93 (NOT keeping the factory pocket)........................3
Impulse 1990-93 (keeping the factory pocket)............................... 4
Pickup 1988-95.............................................................................5
Rodeo 1992-95............................................................................. 5
Stylus 1990-91 (NOT keeping the factory pocket)...........................3
Stylus 1990-91 (keeping the factory pocket).................................. 4
Trooper 1988-91...........................................................................5
*OPTIONAL
*OPTIONAL
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION
rev. 271202
6
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) Phillips screws securing the radio trim
bezel to the bottom of the dash and remove
the bezel. Remove (2) screws securing the
factory head unit to the sub-dash and
disconnect the wiring.
1
CHEVROLET Spectrum 1985-89
GEO Spectrum 1989
3
3
Using the v-cut as a guide, cut and remove the bottom portion of the Radio Housing. Mount
the converted Brackets to the Housing with (4) #6 Phillips Screws supplied. Skip to the
Installation Instructions for ALL VEHICLES on Page #7.
Using the v-cut as a guide, cut and remove the bottom portion of the Radio Housing. Mount
the converted Brackets to the Housing with (4) #6 Phillips Screws supplied. Skip to the
Installation Instructions for ALL VEHICLES on Page #7.
1
Cut and remove all mounting tabs on
Brackets Set #2 EXCEPT tabs "A". The
mounting tabs can be identified by the
stamped letter on the back of each tab.
2
"A"
"A"
"A"
"A"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) Phillips screws from each side of the
dash trim bezel and remove the bezel.
Remove (4) Phillips screws securing the
bracket assembly. Remove the factory
head unit and disconnect the wiring.
1
ISUZU I-Mark 1985-91
2
Cut and remove all mounting tabs on
Brackets Set #2 EXCEPT tabs "A". The
mounting tabs can be identified by the
stamped letter on the back of each tab.
Loading...