Metra Electronics CADILLAC 95-2004 User Manual

INSTALLATION INSTRUCTIONS FOR PART 95-2004
APPLICATIONS
Cadillac
1997-2001 Catera
1996-1999 Deville
(Column Shift Only)
95-2004
KIT FEATURES
• DDIN Head Unit Provision
• ISO Stacked Head Unit Provision
• ( A) DDIN Brackets • ( B) DDIN Trim Plate • ( C) (4) Speed Clips • ( 4) Phillips Head Screws
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
HARNESS:
• GMRC-03 - 1997-2002 Cadillac Interface W/O Onstar
A
B
• GMOS-06 - 1997-2002 Cadillac Interface W/ Onstar
ANTENNA ADAPTER:
• 40-GM10 - GM Antenna Adapter
C
• Phillips Screwdriver • Panel Removal Tool • Small Flat Blade Screwdriver • Cutting Tool
D
TOOLS REQUIRED:
METRA. THE WORLD’S BEST KITS.™
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
95-2004
K
NOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
TABLE OF CONTENTS
Dash Disassembly
1997-2001 Cadillac Catera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1996-1999 Cadillac Deville
( Column Shift Only)
. ............
1
Kit Preparation
1997-2001 Cadillac Catera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1996-1999 Cadillac Deville
Assembly
Kit 1997-2001 Cadillac Catera / 1996-1999 Cadillac Deville
Shift Only)
( Column Shift Only)
.............
( Column
2
DDIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ISO Stacked Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . 3
Metra recommends using MECP certified technicians.
95-2004
6:5
9
6:59
1997-2001 CADILLAC CATERA
Disconnect the negative battery
1
terminal to prevent an accidental short circuit.
2
Remove (1) Phillips head screw from inside the ashtray and remove ash­tray.
(Figure A)
3
Remove screw covers from the radio trim panel. Remove traction control and hazard switch covers. Then remove switches by depressing tabs and pulling outward.
(Figure B)
DASH DISASSEMBLY
A
B
Remove (4) Phillips head screws
4
from behind covers and ashtray.
Remove radio trim panel and unplug
5
any remaining harnesses from the panel.
Remove (2) Phillips head screws
6
securing the radio. Unplug and remove the radio.
(Figure C)
1996-1999 CADILLAC DEVILLE
Disconnect the negative battery
1
terminal to prevent an accidental short circuit.
C
A
Unsnap and remove radio trim panel.
2
(Open glove box to access.)
Pinch the side clips to disengage
3
radio. Unplug and remove radio.
(Figure A)
1
95-2004
1997-2001 CADILLAC CATERA
Cut and remove the three shaded
1
tabs on both brackets. (Figure A)
KIT PREPARATION
A
1996-1999 CADILLAC DEVILLE
Cut and remove the shaded tab from
1
both brackets, and both of the tabs on the trim plate. (Figure B)
Install (4) speed clips into the sub-
2
dash mounting positions.
(Figure C)
B
C
2
95-2004
DOUBLE DIN / STACKED ISO DIN
HEAD UNIT PROVISIONS
Locate the factory wiring harness in
1
the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
2
Attach the Double DIN brackets to the inside edge of the Double DIN trim plate.
(Figure A)
KIT ASSEMBLY
3
Slide the bracket/radio housing assembly over the Double DIN head unit and secure using the screws supplied with the radio.
Reassemble dash in reverse order of
4
disassembly.
(Figure B)
3
95-2004
NOTES
4
95-2004
NOTES
5
INST95-2004
METRA. THE WORLD’S BEST KITS.™
1-800-221-0932 www.metraonline.com
REV. 12/01/09 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST95-2004
Loading...