Metra Electronics BT-HD01 Installation Manual
METRA. The World’s best kits.
™
metraonline.com
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
REV. 2/9/2016 INSTBT-HD01
Installation instructions for part BT-HD01
CAUTION!
All accessories and switches must be connected before
cycling the ignition. Also, do not remove the factory radio with the key
in the on position, or while the vehicle is running.
• Adds Bluetooth audio streaming to the factory radio
• Can be operated with the handlebar controls
• Will play/pause with ignition on/off
• Will show up on the factory radio as HDBT
• BT-HD01 interface • BT-HD01 harness • 4’ Waterproof USB cable
FEATURES
INTERFACE COMPONENTS
• Wire cutter • Crimp tool • Solder gun • Tape • Torx driver
• Connectors (example: butt-connectors, bell caps, etc.)
TOOLS REQUIRED
BT-HD01
Harley Davidson
Bluetooth Audio
Streaming Interface 2006-2013
Table of Contents
Pre-Installation ....................................................... 2
Fairing Disassembly ........................................... 3-4
Connections to be made ......................................... 5
Installing the BT-HD01 ............................................6
Pairing the BT-HD01 ...............................................6
Operation.................................................................6
APPLICATIONS
HARLEY DAVIDSON (with Advanced Radio)
Electra Glide 2006-2013
Street Glide 2006-2013
Road Glide 2006-2013
BT-HD01
2
Pre-Installation
• Turn the radio on and activate the FM source.
• Turn the ignition key switch to the off position.
• Press and hold any (2) soft buttons on the radio, and then turn the ignition key switch to the on position. The soft buttons are the numbered buttons on the radio.
• Continue holding the (2) soft buttons until “Diag Test” is displayed on the radio screen, and then let go.
• Press the soft key button “4” labeled “Software” on the radio screen.
• The radio screen will then show the current software version. If you do not have V8.250 or higher, please go to the following website to update the radio:
http://www.harleydavidson.com/en_US/Content/pages/genuine_motor_accessories/advanced-audio-system.html
• Follow the instructions on the website exactly as stated. If there are any questions with that process, contact Harley Davidson. Please do not contact Axxess/Metra for
any questions pertaining to updating the radio.
• If the radio has V8.250 or higher software, press the soft button “6” to exit the diagnostic mode.
Attention: Before beginning the installation, check the current software version of the radio following the steps below.
This product will not work on models with software versions lower than V8.250.
BT-HD01
3
Fairing Disassembly
FLH/Batwing models:
1. Cover the front fender.
2. Remove (2) T-27 Torx bolts from
inner fairing (under mirrors)
(Figure A, step 2)
3. Remove (2) T-27 Torx bolts from
outer edges of inner fairing near the
fork tubes (facing forward)
(Figure A, step 3)
4. Remove (3) T-27 Torx bolts from
bottom edge of windshield.
(Figure A, step 4)
Note: Windshield and fairing will
be loose once these screws are
removed. Use extreme caution not
to damage fairing or windshield.
5. Remove windshield taking caution
that the outer fairing is loose.
6. Lift away and unplug headlight to
remove outer fairing. (Figure B)
(Figure A)
(Figure B)
Step 2 Step 2
Step 3
Step 4
BT-HD01
4
Fairing Disassembly
Roadglide/Sharknose models
1. Loosen (6) T-25 Torx bolts from
bottom, middle and top of left and
right sides of the inner fairing.
(Figure A)
2. Use a 1/2” socket or box wrench
to remove the (2) acorn nuts that
hold each turn signal at the lower
fairing. Let the signals hang loose.
(Figure B)
3. Lift away the fairing, unplug the
headlights and remove.
(Figure A)
(Figure B)
Step 1 Step 1
BT-HD01
5
Connections to be made
• Remove the 35-pin connector from the radio. This is the larger connector of the (2)
connectors in the radio. If there isn’t a 35-pin connector in the radio, proceed to the
next step.
• Connect the male end of the BT-HD01 harness into the radio.
• Connect the female end of the BT-HD01 harness into the factory connector in the
vehicle. If there wasn’t a 35-pin connector in the radio, skip this step.
• The following (2) wires connect to the 23-pin radio connector. This is the smaller
connector of the (2) connectors in the radio. The factory connector has the pin cavity
locations stamped onto it.
• Connect the Black wire from the BT-HD01 harness to the wire located in pin-19 of the
23-pin radio connector.
• Connect the Red wire from the BT-HD01 harness to the wire located in pin-20 of the
23-pin radio connector.
Note: The BT-HD01 can operate in two different modes: CD mode (default) or SAT
mode. If you have a factory iPod interface installed and desire to keep it, change the
BT-HD01 to SAT mode. To do this you will need to cut the Grey loop wire coming out of
the BT-HD01, and then switch the 3-pin audio wire connection to the SAT setting.
18
16
23
19 20
This is the wire view of the connector
Loading...