Metra Electronics 99-3410, DW -3410, AW -341GO User Manual
KIT FEATURES
ALL VEHICLES
Shaft and
DIN unit
3
Fig. A
4
Fig.
A
provisions
99-3410
Equalizer
provisions
AW -341GO
DW -3410
KIT COMPONENTS
INSTALLATION
Fig. B
Fig. B
Radio Housing
INSTRUCTIONS
2-SHAFT HEAD UNITS: Slide the
aftermarket head unit into the kit and
secure with shaft nuts. (see Fig. A)
DIN
HEAD UNITS: Cut and remove the
shaft supports. Slide the DIN cage into the
Radio
Housing and secure by bending the
metal locking tabs down. Slide the
aftermarket head unit into the cage until
secure. (see Fig. B)
5 6
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
3
AN EQUALIZER WILL BE INCLUDED :
IF
Slide the aftermarket equalizer into the back of
the Radio Housing. Using the hardware
included with the equalizer, mount the unit to
the kit. (see Fig. A)
IF
AN E QUAL IZE R WIL L NOT B E
INCLUDED:
Plate
into the Radio Housing. (see Fig. B)
Re-connect the battery terminal and test the unit
for proper operation. Slide (4) Speed Clips over
the holes in the sub-dash mounting brackets and
mount the head unit/kit assembly with (4) Phillips
Pan-Head
Screws supplied.
Snap the Equalizer Dummy
REV. 07-29-09
Equalizer
Dummy Plate
(4) #8 x 1" Phillips
Pan-Head Screws
(4) Speed Clips
TOOLS REQUIRED
Phillips screwdriver
Cutting tool
Wrench
APPLICATIONS
CAR
PAGE
CHEVROLET
Tracker 1998-04..........................................................
GEO
Metro 1992-94............................................................
Tracker 1992-97..........................................................
SUZUKI
Aerio 2003.................................................................. 2
Esteem 1995-03..........................................................
Sidekick 1992-98........................................................
Swift 1992-94.............................................................
Vitara series 1999-04.................................................1
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• Please visit www.metraonline.com for specific interface
applications
Antenna Adapter:
• 40-GM10 - GM antenna adapter 88-up
NOWLEDGE IS
K OWER
E
nhance your installation and fabrication skills
by en
rolling in the most recognized and respected
mobile elect
Log onto ww
or call 800-354-6782 for mo
and take steps towa
ronics school in our industry.
w.installerinstitute.com
rd a better tomorrow.
P
re information
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001-2009 METRA ELECTRONICS CORP.
1
1
1
2
1
1
CHEVROLET Tracker 1998-04 • GEO Tracker 1992-97
SUZUKI Sidekick 1992-98 / Vitara series 1999-04
SUZUKI Aerio 2003
1
Di sco nne ct t he neg ati ve
battery
terminal to prevent an
acc i den t a l
Remove
and
Remove
screw
climate
remove
Unclip
Remove
factory
out
and disconnect the wiring.
sh o r t c i rcui t .
the cigarette lighter
climate control knobs.
the ashtray and (1)
exposed. Pull out on the
control cluster and
(2) screws exposed.
the radio trim bezel.
(4) screws from the
head unit, slide the unit
GEO Metro / SUZUKI Swift 1992-94
1
2
Fig. B
A
B
B
Cut and remove all mounting tabs on the Radio Housing
EXCEPT tabs "B". (The mounting tabs can be identified by
the stamped letter on the back of each tab). (see Fig. A). Cut
and remove the (2) side clips on the back side of the radio trim
bezel. (This will provide proper clearance when re-attaching
the bezel after the aftermarket head unit has been installed).
(see
Fig. B). Skip to the Installation Instructions for ALL
VEHICLES
Fig.
on Page #3.
B
B
2
A
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the dash trim bezel and remove. Remove
(4) Phillips screws securing the factory head
unit and disconnect the wiring.
SUZUKI Esteem 1995-03
1 2
2
B
B
B
B
Cut and remove all mounting tabs on the
Radio
Housing EXCEPT tabs "B". The
mounting tabs cab be identified by the
stamped letter on the back of each tab. Skip
to
the Installation Instructions for ALL
VEHICLES
on Page #3.
B
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the climate control knobs. Remove (1)
Phillips screw above and (2) Phillips screws
below the climate controls. Unclip the radio
trim bezel. Remove (4) screws from the
factory head unit, slide the unit out and
disconnect the wiring.
1
A
A
Cut and remove all mounting tabs on the
Radio
Housing EXCEPT tabs "A". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES
on Page #3.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the climate control knobs. Remove (1)
Phillips screw located above the radio
opening. Unclip the radio trim bezel.
Remove (4) screws from the factory head
unit, slide the unit out and disconnect the
wiring.
B
B
B
Cut and remove all mounting tabs on the
Radio
Housing EXCEPT tabs "B". The
mounting tabs cab be identified by the
stamped letter on the back of each tab. Skip
to
the Installation Instructions for ALL
VEHICLES
on Page #3.
2
Loading...