Refer to the IHF-1000 manual for operation. All audio signals from
the IHF-1000 will be played through the car stereo. Adjust the volume using the radio’s volume knob to a comfortable level.Audio
from FM, CD, Satellite etc. will be automatically paused or muted
while calls are in process. Any OnStar operations will preempt the
operation of the IHF-1000. Keep in mind that if OnStar operations
start while you are on a call, the call will continue and the caller will
be able to hear you – watch what you say!
The vehic
le’s radio does not need to be on for IHF-1000 operations,
but the vehicle’s ignition must be on or in accessory mode.
ABTI-GM2
©Copyright 2007 Metra Electronics Corporation
1-800-221-0932 www.metraonline.com
ABTI-GM2
©Copyright 2007 Metra Electronics Corporation
1-800-221-0932 www.metraonline.com
4
ABTI-GM2 ABTI-GM2
AAPPPPLLIICCAATTIIOONNSS IINNCCLLUUDDEE:
:
REV. 08/14/07 INSTABTI-GM2
* READ IMPORTANT WARNING ON PAGE 1
BEFORE ATTEMPTING ANY INSTALLATION
CHEVROLET
Cobalt 2005-06
Equinox 2005-06
Malibu/Malibu Maxx 2004-07
PONTIAC
G6 2005-07
T
orrent 2006
GENERAL MOTORS
LAN
BLUETOOTH INTERFACE
INSTALLATION
MANUAL
5) Connect the 24 pin cap on the ABTI-GM2 cable to the 24 pin
plug connected to the vehicle (the connector that was removed
from the back of the radio).
10) Install the IHF-1000 microphone in an appropriate location
(see IHF-1000 instructions), route the wire to the IHF-1000 harness, and attach the microphone connector to the harness.
11) Secure all components, and reinstall the radio.
12) Reconnect the vehicle battery.
6) Connect the 12 pin cap on the ABTI-GM2 cable to the 12 pin
plug connected to the vehicle (the connector that was removed
from the back of the radio).
ABTI-GM2
GM LAN
ca
ble
ha
rne
ss
White
RE-PLUG
EX
ISTI
NG
F
ROM CAR
UNPL
UG
EXI
STI
NG
UNPL
UG
EXI
STI
NG
F
ROM CAR
24 p
in p
lug
12 p
in p
lug
RE-
PLU
G E
XIS
TING
F
ROM CAR
FROM CAR
24 p
in p
lug
12 p
in p
lug
ABTI-GM2
GM LAN ca
ble
ha
rne
ss
UNPL
UG
EXI
STING
UNPL
UG EXI
STING
FROM CAR
12 p
in p
lug
RE-
PLU
G E
XIS
TING
FROM CAR
FROM CAR
24 p
in p
lug
12 p
in p
lug
7) Connect the white 10-pin plug on the ABTI-GM2 cable to the
ABTI-GM2 module.
ABTI-GM2
GM LAN
ca
ble
ha
rne
ss
8 pin
IHF-1000 keypad
plug
White
RE-P
LUG
EX
ISTI
NG
FROM CAR
UNPL
UG
EXI
STING
UNPL
UG EXI
STING
F
ROM CAR
24 p
in p
lug
12 p
in p
lug
RE-
PLU
G E
XIS
TING
F
ROM CAR
FROM CAR
24 p
in p
lug
12 p
in p
lug
9) Install the IHF-1000 keypad on the dashboard of the vehicle,
and route the wire to the IHF-1000 harness. Attach the keypad
connector to the harness.
ABTI-GM2
GM LAN
ca
ble
ha
rne
ss
8 pin
IHF-1000 keypad
plug
White
RE-P
LUG
EX
ISTI
NG
UNPL
UG
EXI
STING
24 pin plug
TING
24 p
in p
lug
OPERATION
The ABTI-GM2 is designed to allow full integration of Motorola’s
IHF-1000 Bluetooth Hands free kit (Sold Separately) with the
GMLAN vehicles listed below. The kit will allow users to listen to
phone calls through their car stereo. The currently playing radio
source will be automatically muted, and the phone volume may
be controlled by the radio. OnStar operation is unaffected.
8) Connect the white 8 pin plug on the IHF-1000 cable to the
ABTI-GM2 power cable, and connect the other end of the power
cable to the ABTI-GM2 module.
* IMPORTANT WARNING
THIS PRODUCT INCLUDES INSTRUCTIONS FOR INSTALLATION WHICH MUST BE
CAREFULLY FOLLOWED. THE INSTRUCTIONS ARE WORDED
IN SUCH A MANNER TO ASSUME THAT THE INSTALLER IS CAPABLE
OF COMPLETING THESE TYPE OF ELECTRONIC INSTALLATIONS.
IF YOU ARE UNCLEAR AS TO WHAT YOU ARE INSTRUCTED TO DO OR BELIEVE
THAT YOU DO NOT UNDERSTAND THE INSTRUCTIONS SO AS TO PROPERLY
AND SAFELY COMPLETE THE INSTALLATION YOU SHOULD CONSULT A TECHNICIAN WHO DOES HAVE THIS KNOWLEDGE AND UNDERSTANDING. FAILURE TO
FOLLOW THESE INSTRUCTIONS
CAREFULLY AND TO INSTALL THE INTERFACE AS DESCRIBED COULD
CAUSE HARM TO THE VEHICLE OR TO SAFETY SYSTEMS ON THE VEHICLE.
INTERFERENCE WITH CERTAIN SAFETY SYSTEMS COULD CAUSE HARM TO
PERSONS AS WELL. IF YOU HAVE ANY QUESTIONS IN THIS REGARD
PLEASE CALL THE HELP LINE OR THE METRA AT 1-800-221-0932 FOR
ASSISTANCE.
21
ABTI-GM2
ABTI-GM2ABTI-GM2
INSTALLATION PROCEDURE
1) Disconnect the vehicle battery.
2) Remove the radio from the dashboard, and disconnect any
cables connected to the radio.
3) Insert the 24 pin plug on the ABTI-GM2 cable into the rear of
the radio.
4) Insert the 12 pin plug on the ABTI-GM2 cable into the rear of
the radio.
3
INSTALLATION COMPONENTS
1) ABTI-GM2 cable (Included).
2) ABTI-GM2 power cable (Included).
3) ABTI-GM2 module (Included).
4) Motorola IHF-1000 kit (Sold separately).
5) Installation tools, wire ties, and mounting hardware as needed.
UNPL
UG
EXIST
ING
UNPL
UG
EXI
STI
NG
FROM CAR
FROM CAR
24 p
in p
lug
12 p
in p
lug
ABTI-GM2
GM
LAN ca
ble
ha
rne
ss
White
RE-P
LUG
EX
ISTI
NG
FROM CAR
UNPL
UG
EXI
STI
NG
UNPL
UG
EXI
STING
FROM CAR
24 p
in p
lug
12 p
in p
lug
RE-
PLU
G E
XIS
TING
FROM CAR
24 p
in p
lug
12 p
in p
lug
ABTI-GM2
GM
LAN ca
ble
ha
rness
8 pin
White
RE-P
LUG
EX
ISTI
NG
FROM CAR
UNPL
UG
EXI
STI
NG
UNPL
UG
EXI
STING
FROM CAR
24 p
in p
lug
12 p
in p
lug
RE-
PLU
G E
XIS
TING
FROM CAR
24 p
in p
lug
12 p
in p
lug
Loading...