Metra Electronics 99-9501B, 99-9501G Installation Manual

Page 1
INSTALLATION INSTRUCTIONS FOR PART 99-9501
APPLICATIONS
JAGUAR S-TYPE
2003-2008
KIT FEATURES
• DIN Head Unit Provision w/ removable pocket
• ISO DIN Head Unit Provision w/ removable pocket
• ISO Stacked Head Unit Provision
• TWO FINISHES AVAILABLE: 99-9501B=BLACK, 99-9501G=GREY
A) Radio Housing B) ISO Brackets C) ISO Trim Plate D) DDIN Brackets E) DDIN Trim Plate F) Pocket G) (2) Pocket C-Clips H) (2) Small Phillips screws
KIT COMPONENTS
A
TOOLS REQUIRED:
• Small Flat Blade Screwdriver • Torx Screwdriver
• Socket Wrench • Cutting Tool
1-800-221-0932
© COPYRIGHT 2007-2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
99-9501B 99-9501G
B
C
D
E
F
G
H
JAGUAR X-TYPE
2002-2008
(NON-NAV MODELS)
METRA. THE WORLD’S BEST KITS.™
Page 2
Dash Disassembly
-
Jaguar S-Type 2003-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . .
1,2
-
Jaguar X-Type 2002-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,4
Kit Preparation
- Jaguar S-Type 2003-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
- Jaguar X-Type 2002-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Kit
Assembly
- DIN Head Unit Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
- ISO DIN Head Unit Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
- DDIN Head Unit Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TABLE OF CONTENTS
99-9501
*Note: Ref
er also to the instructions included with the aftermarket radio.
K
NOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
Metra recommends MECP certified technicians.
Page 3
99-9501 DASH DISASSEMBLY
JAGUAR S-TYPE 2003-2008
NON-NAV MODELS
A
B
1
Disconnect the negative battery ter-
minal to prevent an accidental short circuit.
1
Remove cup holder and (2) screws securing center console storage com­partment and remove compartment. (
Figure A)
2
Unclip and remove the trim panel around the shifter.
(Figure B)
3
Continued on page 2
Page 4
99-9501 DASH DISASSEMBLY
JAGUAR S-TYPE 2003-2008
NON-NAV MODELS
D
2
Continue to kit assembly
Remove (4) screws securing the r
adio/climate control assembly to the dash. Unplug and remove assembly. (
Figure D)
Remove (4) screws securing the radio to the assembly and remove the radio. Retain the assembly for re-use during kit assembly.
6
5
C
Unclip and remove the trim panel sur­rounding the radio/climate controls/ashtray and front half of the center console.
(Figure C)
4
Page 5
99-9501 DASH DISASSEMBLY
JAGUAR X-TYPE 2002-2008
NON-NAV MODELS
A
B
C
3
Disconnect the negative battery ter-
minal to prevent an accidental short circuit.
1
Unclip and remove the trim panel around the shifter. (
Figure A)
2
Remove (2) screws from bottom edge of ashtray assembly then unclip and remove ashtray assembly.
(Figure B)
3
Remove (2) screws from inside ash­tray cavity at bottom edge of radio.
(Figure C)
4
Continued on page 4
Page 6
99-9501 DASH DISASSEMBLY
D
E
F
4
Continue to kit assembly
Unclip, unplug and remove hazard switch/seat heater switc
h trim panel above climate control/radio assembly. (
Figure D)
5
Remove (2) screws from inside switch panel cavity at top edge of cli­mate controls. (
Figure E)
6
Unplug and remove the climate con­trol/radio assembly. (
Figure F)
7
Remove (4) screws securing the radio to the assembly and remove the radio. Retain the assembly for re-use during kit assembly.
8
JAGUAR X-TYPE 2002-2008
NON-NAV MODELS
Page 7
99-9501 KIT ASSEMBLY
5
Cut and remove the locator closest to the face of the radio housing for the S-Type.
(Figure A)
Cut and remove the locator farthest from the face of the radio housing for the X-Type.
(Figure B)
A
B
KIT PREPARATION
JAGUAR S-TYPE 2003-08
JAGUAR X-TYPE 2002-08
Continue to kit assembly
Page 8
99-9501 KIT ASSEMBLY
A
B
C
6
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
1
Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A)
2
Snap the pocket into the bottom opening of the radio housing. (Figure B)
3
Secure the pocket by inserting the c­clips into the opening between the pocket and the bottom of the radio housing. (Figure B)
4
Slide the aftermarket head unit into the cage and secure. (Figure C)
5
Attach the radio housing to the cli­mate control bracket assembly and screw the bottom together with the two supplied Phillips screws.
6
Reassemble dash in reverse order of disassembly.
7
JAGUAR S-TYPE 2003-2008
JAGUAR X-TYPE 2002-2008
DIN HEAD UNIT PROVISION
Page 9
99-9501 KIT ASSEMBLY
A
B
C
7
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
1
Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A)
2
Snap the pocket into the bottom opening of the radio housing. (Figure B)
3
Secure the pocket by inserting the c­clips into the opening between the pocket and the bottom of the radio housing. (Figure B)
4
Slide the head unit into the radio opening until the side clips engage. (Figure C)
5
Snap the Trim plate into the Radio Housing. (Figure C)
6
Attach the radio housing to the cli­mate control bracket assembly and screw the bottom together with the two supplied Phillips screws.
7
Reassemble dash in reverse order of disassembly.
8
JAGUAR S-TYPE 2003-2008
JAGUAR X-TYPE 2002-2008
ISO DIN HEAD UNIT PROVISION
Page 10
99-9501 KIT ASSEMBLY
A
B
8
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
1
Snap the Double DIN brackets to the inside edge of the Radio Housing. (Figure A)
2
Slide the Double DIN head unit or stacked ISO head units into the bracket/radio housing assembly and secure the Double DIN head unit or stacked ISO head units to the assem­bly using the screws supplied with the radio. (Figure B)
3
Snap the double DIN trim plate into the radio housing. (Figure B)
4
Attach the radio housing to the cli­mate control bracket assembly and screw the bottom together with the two supplied Phillips screws
5
Reassemble dash in reverse order of disassembly.
6
JAGUAR S-TYPE 2003-2008
JAGUAR X-TYPE 2002-2008
DDIN HEAD UNIT PROVISION
Page 11
NOTES
99-9501
Page 12
INSTRUCTIONS
1-800-221-0932
REV. 12/08/09 © COPYRIGHT 2003-2009 METRA ELECTRONICS CORPORATION INST99-9501
www.metraonline.com
99-9501 INSTRUCTIONS
METRA. THE WORLD’S BEST KITS.™
Loading...