C
AUTION: Metra recommends disconnecting the negative battery
terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your
local Dealership for more information. All accessories, switches,
climate controls panels, and especially air bag indicator lights
must be connected before reconnecting the battery or cycling
the ignition. Also, do not remove the factory radio with the key
in the on position, or the vehicle running. It would be best to
remove the key from the ignition and then wait a few seconds
before removing the factory radio.
Installation instructions for part 99-9013HG
•
A) Radio trim panel • B) Radio housing • C) Radio brackets • D) Pocket • E) (8) #8 x 3/8” Phillips screws
KIT COMPONENTS
WIRING &
ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • XSVI-9006-NAV Antenna Adapter: • 40-EU56
• Panel removal tool • Phillips screwdriver
• Euro radio removal keys (2 sets)
Metra part number: 86-9001
TOOLS REQUIRED
V
olkswagen Golf 2015-up
99-9013HG
A
EDC
B
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted high-gloss black
KIT FEATURES
99-9013HG
Dash Disassembly
1. Open the door below the climate
control panel. (Figure A)
2.
Unc
lip and remove the climate
control trim panel. (Figure B)
3.
Remove and unplug the passenger
airbag hazard switch assembly.
4.
Unc
lip the vent/display trim bezel.
(Figure C)
Continued on next page
(Figure A) (Figure B) (Figure C)
99-9013HG
5. Unclip and remove the vents from
the factory trim panel and save for
kit assembly. (Figure D)
6.
Remove the factor
y radio display
using (2) sets of euro radio removal
keys (top and bottom). (Figure E)
7.
Remove the
VW Infotainment unit
from the glove compartment using
euro radio removal keys to access
the antenna and power harness.
(Figure F)
Continue to kit assembly
Dash Disassembly
(Figure D) (Figure E) (Figure F)
99-9013HG
Kit Assembly
ISO DIN radio provision with pocket
1. Cut and remove the (2) plastic
shaded areas from the sub dash.
(Figures A, B)
2.
Slide the
radio housing into the dash
cavity and push in to engage the
clips to the sub dash. (Figure C)
3.
Remove the metal “DIN” sleeve and
trim ring from the aftermarket radio.
4. Attach the radio brackets to the
radio using the screws supplied
with the radio. (Figure D)
5. Screw the pocket into the radio
and bracket assembly using
(4) #8 x 3/8” screws supplied with
the kit. (Figure D)
6. CAUTION!
The airbag light must be
plugged in before the ignition is
cycled on. Failure to do so will
cause an SRS (Airbag) fault that
can only be turned off by the
dealership.
Locate the factory wiring harness
in the dash and make all necessary
wire and antenna connections.
Metra recommends using the
proper mating adapter from
Metra or AXXESS. Re-connect the
negative battery terminal and test
the radio for proper operation
Continued on next pa
ge
(Figure D
(Figure A) (Figure C)
(Figure B)
Remove this
shaded area first
Remove this shaded area
second. It is behind the first
piece that was removed.
99-9013HG
Kit Assembly
(Figure E)
(Figure F)
7. Slide the radio into the radio
housing and secure with
(4) #8 x 3/8” screws supplied
with the kit. (Figure E)
8.
Insert the factor
y vent assembly
into the 99-9013HG radio trim
panel. (Figure F)
9.
Reassemble the dash in the
reverse
order of disassembly, using
the 99-9013HG radio trim panel.
99-9013HG
Kit Assembly
ISO DDIN radio provision
1. Cut and remove the (2) plastic
shaded areas from the sub dash.
(Figures A, B).
2.
Slide the
radio housing into the
dash cavity and push in to engage
the clips to the sub dash.
(Figure C)
3.
Attach the
radio brackets to the
radio using the screws supplied
with the radio.
4. CAUTION!
The airbag light must be
plugged in before the ignition is
cycled on. Failure to do so will
cause an SRS (Airbag) fault that
can only be turned off by the
dealership.
Loca
te the factory wiring harness
in the dash and make all necessary
wire and antenna connections.
Metra recommends using the
proper mating adapter from
Metra or AXXESS. Re-connect the
negative battery terminal and test
the radio for proper operation
Continued on next page
(Figure A) (Figure C)
(Figure B)
Remove this
shaded area first
Remove this shaded area
second. It is behind the first
piece that was removed.
99-9013HG
Kit Assembly
(Figure E)
(Figure F)
5. Slide the radio into the radio
housing and secure with
(4) #8 x 3/8” screws supplied
with the kit. (Figure D)
6. Insert the factory vent assembly
into the 99-9013HG radio trim
panel. (Figure E)
7. Reassemble the dash in the
reverse
order of disassembly, using
the 99-9013HG radio trim panel.
Loading...