Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take
steps toward a better tomorrow.
TABLE OF CONTENTS
•
Dash Disassembly
- GLI 2008 -09................................................................................1,2
- Eos 2007-09................................................................................... 5
•
Kit Assembly:
- DIN Head Unit Provision with Pocket ............................................6
- ISO Head Unit Provision with Pocket .............................................7
- Double DIN Head Unit Provision.....................................................8
- Stacked ISO Head Unit Provision ...................................................9
•
Final Assembly .............................................................................10
Page 3
99-9011
NEW JETTA 2005-09/GLI 2008-09
GTI 2006-09/RABBIT 2006-09
Disconnect the negative battery
1
terminal to prevent an accidental
short circuit.
2
Unclip and remove the grille from
the top-center of dash.
Remove one T-20 torx screw from
3
black insert from under grille
removed in step one.
(Figure A)
(Figure B)
DASH DISASSEMBLY
R32 2008-09
A
Remove insert.
4
Remove two T-20 torx screws from
5
under black insert removed in step
(Figure D)
two.
D
(Figure C)
B
C
1
Page 4
99-9011
NEW JETTA 2005-09/GLI 2008-09
GTI 2006-08-09/RABBIT 2006-09
R32 2008-09
Unsnap and remove the vent
6
assembly above the radio.
Remove two T-20 torx screws from
7
top sides of radio/climate panel.
(Figure F)
DASH DISASSEMBLY
E
(Figure E)
Remove panel.
8
Remove four T-20 torx screws to
9
remove the radio.
H
(Figure G)
(Figure H)
F
G
2
Page 5
99-9011
PA
S
S
EN
GER
A
I
R
B
AG
OF
F
ON
VOL
SC
A
N
T
UNE
BA
S
S
T
RE
B
BA
L
FA
D
F
M
AM
CD
A
C
FM2
103.7
M
HZ
72
64
80
1
2
3
4
CC 2009 / VW PASSAT 2006-2009
Disconnect the negative battery
1
terminal to prevent an accidental
short circuit.
Unclip and remove trim panel sur-
2
rounding radio. (Figure A)
Remove (4) T-20 Torx screws to
3
remove radio.
DASH DISASSEMBLY
A
3
Page 6
99-9011
PASSENGER
AIR BAG
PASSENGER
AIR BAG
P
ASSENGER
AIR BAG
P
ASSENGER
AIR BAG
AF
PASSENGER
AIR BAG
AF
Disconnect the negative battery
1
terminal to prevent an accidental
short circuit.
Unclip and remove passenger air
2
bag light panel to the right of the
hazard light button.
Unclip and remove the panel with
3
the two slots in it to the left of the
hazard light button.
Remove (2) T-20 Torx screws
4
exposed behind the two panels
removed in the two previous steps.
(Figure B)
(Figure A)
(Figure A)
DASH DISASSEMBLY
TIGUAN 2009
A
B
Unclip and remove the trim panel
5
surrounding the radio.
Remove (4) T-20 Torx screws secur-
6
(Figure C)
ing the radio. Unplug and remove
(Figure D)
the radio.
D
C
4
Page 7
99-9011
DASH DISASSEMBLY
EOS 2007-2009
A
Disconnect the negative battery
1
terminal to prevent an accidental
short circuit.
Unclip and remove the radio trim
2
panel.
Remove the (4) screws securing the
3
radio. Unplug and remove the radio.
(Figure B)
(Figure A)
B
5
Page 8
99-9011
KIT ASSEMBLY
DIN HEAD UNIT PROVISION WITH POCKET
Slide the DIN cage into the Radio
1
Housing and secure by bending
the metal locking tabs down.
(Figure A)
Slide the aftermarket head unit
2
into the cage and secure.
(Figure B)
Snap the pocket into the radio hous-
3
(Figure C)
ing.
A
B
C
6
Page 9
99-9011
KIT ASSEMBLY
ISO HEAD UNIT PROVISION WITH POCKET
Mount the ISO Brackets to the
1
head unit with the screws supplied with the unit.
Slide the head unit into the radio
2
opening until the side clips
engage.
Snap the ISO Trim Plate into the
3
Radio Housing.
(Figure B)
(Figure A)
(Figure C)
A
Snap the pocket into the radio hous-
4
(Figure C)
ing.
B
C
7
Page 10
99-9011
DOUBLE DIN HEAD UNIT PROVISION
Cut and remove center divide from
1
radio housing.
Snap the DDIN brackets to the
2
inside edge of the radio housing.
(Figure B)
Slide the DDIN radio unit into the
3
DDIN bracket/radio housing assembly and secure the unit to the kit
using the screws supplied with the
head unit.
(Figure A)
(Figure C)
KIT ASSEMBLY
A
B
Snap the DDIN trim-plate onto the
4
housing/radio assembly.
(Figure C)
C
8
Page 11
99-9011
STACKED ISO HEAD UNIT PROVISION
Cut and remove center divider
1
from radio housing.
Snap the DDIN brackets to the
2
inside edge of the radio housing.
(Figure B)
Slide the stacked ISO DIN units into
3
the DDIN bracket/radio housing
assembly and secure the units to the
kit using the screws supplied with
the head units.
(Figure C)
(Figure A)
KIT ASSEMBLY
A
B
Snap the DDIN trim-plate onto the
4
housing/radio assembly.
(Figure C)
C
9
Page 12
99-9011
FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
C
D
1
2
3
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually
tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble in reverse order of disassembly.
A)Strip wire ends back 1/2"
B)Twist ends together
C)Solder
D)Tape
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.