Metra Electronics 99-8723B, 99-8724B Installation Manual

Page 1
CAUTION!
All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.
Metra. The World’s Best Kits.
MetraOnline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 09/27/17 INST99-8723B
INSTALLATION INSTRUCTIONS
99-8723B
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted matte black
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (8) #8 x 3/8” Phillips screws
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• T-20 Torx driver
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Assembly
–ISO DIN radio provision with pocket ..................3
–ISO DDIN radio provision .....................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Please visit metraonline.com for additional adapters and accessories.
A B C D
Mercedes-Benz ML 2006-2011
Page 2
1.800.221.0932 | MetraOnline.com
2
1. Unsnap and remove climate controls.
2. Remove (2) T-20 Torx screws from the
radio retaining tabs.
3. Push straight down on the retaining tabs to release the factory radio.
Continue to Kit Assembly
DASH DISASSEMBLY
Please visit Metraonline.com for
Dash Disassembly illustrations.
Page 3
REV. 9/27/2017 INST99-8723B
3
(Figure B)
(Figure A)
ISO-DIN radio provision with pocket
1. Attach the
radio brackets
to the
radio
trim panel
using (4) #8 x 3/8” Phillips
screws supplied. (Figure A)
2. Attach the
pocket
to the bracket assembly using the (4) supplied #8 x 3/8” Phillips screws. (Figure B)
3. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
4. Slide the radio into the completed assembly, and then secure it to the assembly using screws supplied with the radio. (Figure C)
5. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation.
6. Reassemble the dash in reverse order of disassembly.
ISO-DDIN radio provision
1. Attach the
radio brackets
to the
radio
trim panel
using (4) #8 x 3/8” Phillips
screws supplied. (Figure A)
2. Slide the radio into the completed assembly, and then secure it to the assembly using screws supplied with the radio. (Figure B)
3. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation.
4. Reassemble the dash in reverse order of disassembly.
KIT ASSEMBLY
(Figure A)
(Figure B)
(Figure C)
Page 4
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
®
Metra recommends MECP certified technicians
IMPORTANT If you are having difficulties with the installation of this product,
please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
Metra. The World’s Best Kits.
MetraOnline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 09/27/17 INST99-8723B
INSTALLATION INSTRUCTIONS
99-8723B
Loading...