INSTALLATION INSTRUCTIONS FOR PART 99-8223
APPLICATIONS
Toyota Corolla
2009-10
99-8223/
99-8223S
KIT FEATURES
• DIN Radio With Pocket Provision
• ISO Mount Radio with Pocket Provision
• Painted To Match Factory Dash
99-8223= BLACK
99-8223S= SILVER
KIT COMPONENTS
• A) Radio Housing • B) Radio Housing Trim Plate • C) Radio Housing Brackets
•D) ISO Brackets • E) ISO Trim Plate
A
D
B
E
Small Flat Blade Screwdriver/ Panel Removal Tool
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
C
Harness & Antenna Connections (sold separately)
• 70-1761 Toyota Harness 87-up
• TYTO-01 Toyota Amp Interface 03-up
TOOLS REQUIRED:
• Phillips Screwdriver
www.metraonline.com
99-8223
K
NOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
TABLE OF CONTENTS
Dash Disassembly
-
Toyota Corolla 2009-10 . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . 1
Kit Assembly
- DIN Radio with Pocket Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
- ISO Mount Radio with Pocket Provision . . . . . . . . . . . . . . . . . . . . . . . . 3
Final
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
*Note:
Refer also to the instructions included with the aftermarket radio.
99-8223 DASH DISASSEMBLY
Toyota Corolla 2009-10
Disconnect the negative battery ter-
1
minal to prevent an accidental short
circuit.
Unclip and remove the (4) side trim
2
panels from the right and left side of
the radio and a/c controls. (
Unclip and remove the a/c vent panel
3
above the factory radio.
Remove (4) 10 MM bolts securing the
4
radio.
(Figure C)
Remove (4) plastic clips from the
5
back of the factory radio. (Retain the
clips for re-use during kit assembly.)
Continue to kit assembly.
Figure A)
(Figure B)
A
B
C
1
99-8223 KIT ASSEMBLY
DIN RADIO WITH POCKET PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Attach the clips removed from the fac-
1
tory radio to the back of the radio
housing trim plate.
2
Slide the Radio Housing Brackets onto
the sides of the Radio Housing until the
side clips engage. NO
marked Left and Right.
3
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward.
(Figure A)
TE: Tabs are
(Figure B)
(Figure C)
Slide the aftermarket radio into the
4
cage until it snaps into place.
Continue to final assembly.
D
B
(Figure D)
C
2
99-8223 KIT ASSEMBLY
ISO MOUNT RADIO WITH POCKET PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Attach the clips removed from the fac-
1
tory radio to the back of the radio
housing trim plate.
2
Slide the Radio Housing Brackets onto
the sides of the Radio Housing until the
side clips engage. NO
marked Left and Right.
3
Mount the ISO Brackets to the radio
using the screws supplied with the
(Figure C)
radio.
Slide the radio into the radio housing
4
until it snaps into place.
Snap the Trim plate onto the front of
5
the Radio Housing.
(Figure A)
TE: Tabs are
(Figure B)
B
(Figure D)
(Figure D)
Continue to final assembly.
D
C
3
99-8223 FINAL ASSEMBLY
FINAL ASSEMBLY
A
(A) Strip wire ends back 1/2"
B
B) Twist ends together
C) Solder
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
1
proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
2
Reassemble in reverse order of disassembly using the 99-8223 Radio Housing
3
Trim Plate in place of the factory radio trim panel.
D) Tape
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’
s specifications.
4
99-8223
NOTES
5
99-8223 INSTRUCTIONS
1-800-221-0932
REV. 04/29/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-8223
www.metraonline.com
Loading...