Metra Electronics 99-8214TB, 99-8214TG User Manual
INSTALLATION INSTRUCTIONS FOR PART 99-8214
APPLICATIONS
Toyota Tacoma 2005-2011
99-8214TB
99-8214TG
KIT FEATURES
• DIN Head Unit Provision With Pocket
• ISO DIN Head Unit Provision With Pocket
• Double DIN Head Unit Provision
• Stacked ISO DIN Head Unit Provision
• Painted And Textured To Match Factory Dash
• Available In Two Colors:
99-8214TB = BLACK, 99-8214TG = GRAY
• Both kits are factory “golf ball” style
textured.
KIT COMPONENTS
• A) Radio Housing • B) Radio Housing Brackets
• C) Radio Housing Trim Panel • D) ISO Brackets
• E) ISO Trim Plate • F) (4) #6 x 3/8” Phillips Pan Head Screws
• G) (4) #8 X 3/8” Phillips Truss Head Screws • H) Double DIN Trim Plate • I) Clock/Hazard Switch Bracket
B
E
A
I
C
D
G
H
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1761 - Toyota harness 1987-up
• TYTO-01 - Toyota amp interface harness 2003-up
Antenna Adapter:
• Not required
F
TOOLS REQUIRED:
Phillips Screwdriver • Small Flat Blade Screwdriver • Socket Wrench
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
99-8214
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills
by enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 for more information
and take steps toward a better tomorrow.
TABLE OF CONTENTS
Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,4,5,6
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
99-8214
SCAN
TEXT
PWR VOL
SCAN
TEXT
PWR VOL
DASH DISASSEMBLY
TOYOTA TACOMA 2005-2011
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
Unclip and remove A/C control panel.
(Figure A)
3
Remove (4) 10 MM bolts securing
radio.
4
Unclip and remove entire panel
(Figure B)
including hazard switch and clock.
(Figure C)
5
Remove the left and right radio
brackets from the radio chassis.
(Figure D)
6
Unclip and remove the clock/hazard
switch assembly from the factory
radio housing trim panel.
(Figure E)
A
B
Continue to Kit Preparation.
E
D
C
1
99-8214
H
M
P
A
S
S
E
N
G
E
R
P
A
S
S
E
N
G
E
R
INSERT CLO
CK/H
AZAR
D SW
ITCH A
SS
EMBL
Y
FROM
REA
R OF 9
9-821
4 RAD
IO HOU
SING
TRIM PANE
L
H
M
PASSENGER
PASSENGER
KIT PREPARATION
TACOMA 2005-2011
(SKIP KIT PREPARATION WHEN INSTALLING DDIN RADIO)
A
Attach the clock/hazard switch
1
bracket to the radio housing using
the (4) #6 x 3/8” Phillips pan head
screws.
WARNING:
DO NOT OVERTIGHTEN SCREWS.
Clip the clock/hazard switch
2
assembly into the 99-8214 Radio
Housing Trim Panel.
(Figure A,B)
Continue to Kit Assembly.
B
2
Loading...