Page 1
INSTALLATION INSTRUCTIONS FOR PART 99-8212
APPLICA TIONS
2004-2008 Toyota Solara
99-8212
KIT FEATURES
• DIN Head Unit Provisions with Pocket
• ISO DIN Head Unit Pro
KIT COMPONENTS
visions with Poc
ket
A) Radio Housing w/ Pocket • B) ISO Brackets
C) Radio Housing Brackets • D) (2) PTH-838 Phillips Screws • E) (8) PFH-614 Phillips Screws
F) Trim Plate • G) X-9002 Radio Support Bracket
D
C
A
B
TOOLS REQUIRED:
Socket Wrenc h • Small Flat Blade Screwdriver • Phillips Scr ewdriver
F
E
G
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION Rev.10-02-07
Page 2
99-8212
Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
TABLE OF CONTENTS
Page 3
99-8212
2004-2008 TOYOTA SOLARA
A
Disconnect the negative battery
1
terminal to prevent an accidental
short circuit.
2
Remove the cover from the hazard
switch then unclip and remove the
switch.
Unclip and remove panel above radio
3
including A/C vents and clock.
TIP: Start pulling from the inside of
the hazard switch cavity.
(Figure A)
B
(Figure B)
DASH DISASSEMBLY
Unclip and remove panel surrounding
4
shifter.
Unclip and remove pocket and seat
5
heater switch panel.
Remove (4) 10mm screws to extract
6
radio from sub dash.
E
(Figure C)
(Figure D)
(Figure E)
C
D
1
Page 4
99-8212
2004-2008 TOYOTA SOLARA
Attach the corresponding radio
1
housing bracket to the radio housing
using the included (8) PFH-614 Phillips
screws.
Slide the factory climate control into the
2
assembled radio housing brackets/radio
housing assembly and secure with the
factory hardware.
KIT ASSEMBLY
Attach the radio support to the back of
3
the pocket using the supplied (2) PTF838 Phillips screws.
2
Page 5
99-8212
DIN HEAD UNIT PROVISIONS
A
Slide the DIN cage into the radio
1
housing and secure by bending the
metal locking tabs down.
Slide the aftermarket head unit into
2
the cage and secure.
(Figure A)
(Figure B)
B
KIT ASSEMBLY
3
Page 6
99-8212
ISO DIN HEAD UNIT PROVISIONS
A
Mount the ISO Brackets to the head
1
unit with the screws supplied with
the unit.
Slide the head unit into the radio
2
opening until the side clips engage.
(Figure B)
(Figure A)
B
KIT ASSEMBLY
Snap the trim plate into the radio
3
housing.
(Figure B)
4
Page 7
99-8212
A
B
C
D
Locate the factory wiring harness in the
1
dash. Metra recommends using the proper
mating adapter and making the connections
as shown. (Isolate and individually tape off
the ends of any unused wires to prevent
electrical short circuit)
Re-connect the negative battery terminal
2
and test the unit for proper operation.
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
FINAL ASSEMBLY
Reassemble radio and dash assemblies in
3
reverse order of disassembly.
5
Page 8
INST99-8212
1-800-221-0932 www.metraonline.com
Rev. 07-02-07 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-8212
Loading...