Metra Electronics 99-8163 Installation Manual

Download

Page 1

INSTALLATION INSTRUCTIONS

99-8163

Lexus IS 250/350* - 2006-2013 Lexus IS 250C/350C* - 2006-2015

* U.S. models only

KIT FEATURES

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Painted two-tone gray and black

• Touchscreen display for the climate control

• Passenger seatbelt and airbag indicator

KIT COMPONENTS

• A) Radio trim panel with touchscreen display • B) Radio brackets • C) Pocket • D) (8) #8 x 3/8” Phillips screws

• E) Axxess interface and harnesses (not shown)

A B C D

Metra. The World’s Best Kits.

Note: The kit will not retain the factory ampliﬁer

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Assembly

–ISO DIN radio provision with pocket ..................3

–ISO DDIN radio provision .....................................4

Axxess Interface Installation .................................5

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Axxess touch screen interface and wiring harnesses included Antenna Adapter:

Included with kit

Amp Bypass Harness: Included with kit

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• 10mm socket wrench

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before removing the factory radio. When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition.

Page 2

DASH DISASSEMBLY

1. Unclip and remove the (2) small trim panels from the top of the center console next to the cigarette lighter pocket. (Figure A)

2. Rotate the a/c vents down so they are facing the ﬂoor, release the (4) tabs inside the top edge of the panel, then unclip and remove the a/c vents from the dash. (Figure B, C)

3. Remove (4) 10mm bolts securing the factory radio/climate control assembly, then unplug all harnesses and remove the assembly. (Figure D)

4. Behind the radio/climate control panel

is a module. This module will need to be relocated to allow room for the aftermarket radio.

Continue to Kit Preparation

(Figure A) (Figure C)

(Figure B) (Figure D)

1.800.221.0932 | MetraOnline.com

Page 3

ISO DIN radio provision with pocket

1. Attach the

trim panel with touchscreen

(4) #8 x 3/8” (Figure A)

2. Attach the using the (4) #8 x 3/8” supplied. (Figure B)

3. Remove the metal DIN sleeve and trim ring from the aftermarket radio.

4. Slide the radio into the radio bracket assembly and secure with screws supplied with the radio. (Figure C)

Continue to Axxess Interface

Installation

radio brackets

Phillips screws

pocket

to the

Phillips screws

to the

radio

using the

supplied.

radio brackets

KIT ASSEMBLY

(Figure A) (Figure B) (Figure C)

REV. 11/30/2018 INST99-8163

Page 4

ISO DDIN radio provision

1. Attach the

trim panel with touchscreen

(4) #8 x 3/8” (Figure A)

2. Attach the using the screws supplied with the radio. (Figure B)

Continue to Axxess Interface

Installation

radio brackets

Phillips screws

radio brackets

to the

to the radio

KIT ASSEMBLY

radio

using the

supplied.

(Figure A)

(Figure B)

1.800.221.0932 | MetraOnline.com

Page 5

AXXESS INTERFACE INSTALLATION

INTERFACE FEATURES

• Provides accessory power (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains the passenger airbag and seatbelt indicator

• Allows an aftermarket backup camera to be viewed on the 99-8163 display screen

• Retains the factory AUX-IN jack

• Micro-B USB updatable

INTERFACE COMPONENTS

• Axxess interface (built into the touchscreen display)

• 8163 harness

• 16-pin harness with stripped leads

• 4-pin harness with yellow RCA jacks

• Airbag-indicator/hazard/passenger-seatbelt harness

• Female 3.5mm connector with stripped leads

• AX-AB-LX1, AX-AB-LX2 and AX-AB-LX3 ampliﬁer bypass harness (1 of each)

TABLE OF CONTENTS

Connections ................................................................................................................................ 6-7

Installation ....................................................................................................................................8

Programming ................................................................................................................................ 9

Final assembly ..............................................................................................................................9

Touchscreen display operation ...............................................................................................10-11

Steering wheel control settings .............................................................................................12-13

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun, solder, and heat shrink

• Tape • Wire cutter • Zip ties

REV. 11/30/2018 INST99-8163

Page 6

CONNECTIONS

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the Red wire to the accessory wire.

Note: There will also be an accessory wire from the 8163 harness to connect as well.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

• Connect the Light Green wire to the parking brake wire.

• Tape off and disregard the following (11) wires, they will not be used in this application:

Blue/White, Brown, Gray, Gray/Black, Green, Green/Black, Orange/White, Purple, Purple/Black, White, White/Black

From the 8163 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• Connect the Blue wire to the power antenna wire.

• Connect the Blue/White wire to the accessory wire.

• Connect the Red and White RCA jacks to the audio AUX-IN jacks from the aftermarket radio.

• Tape off and disregard the following (4) wires, they will not be used in this application:

White, White/Black, Gray, Gray/Black

• Use the appropriate ampliﬁer bypass included with the kit to connect to the speakers, following the instructions included with the ampliﬁer bypass. Take note that there are multiple speakers in the vehicle with varying impedance. An external ampliﬁer(s) and either active or passive crossovers will be required (not provided).

Continued on the next page

1.800.221.0932 | MetraOnline.com

Page 7

CONNECTIONS (C ONT.)

3.5mm jack steering wheel control retention:

The 3.5mm jack is to be used to retain audio controls on the steering wheel control.

• For the radios listed below: Connect the male 3.5mm SWC jack from the

• Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/White wire of the connector. Then connect the remaining steering wheel control wire, normally Brown/White, to the Brown wire of the connector.

• Metra OE: Connect the steering wheel control Key 1 wire (Gray) to the Brown wire.

• Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow wire to the Brown wire.

Note: If the Kenwood radio auto detects as a JVC, manually set the radio type to Kenwood.

Refer to the Select Radio screen.

• XITE: Connect the steering wheel control SWC-2 wire from the radio to the Brown wire.

• Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio.

Note: The radio must be updated to rev. 2.1.4 or higher software.

female 3.5mm connector with stripped leads

8163 harness

. Any remaining wires tape off and disregard:

to the

• Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to as Key-A or SWC-1, to the Brown wire from the connector. Then connect the remaining steering wheel control wire, referred to as Key-B or SWC-2, to the Brown/White wire from the connector. If the radio comes with a third wire for ground, disregard this wire.

Note: After the interface has been programmed to the vehicle, refer to the manual

provided with the radio for assigning the SWC buttons. Contact the radio Manufacturer for more information.

• For all other radios: Connect the 3.5mm jack into the port on the radio designated for an external steering wheel control interface. Refer to the manual provided with the radio if in doubt as to where the 3.5mm jack goes to.

4-pin harness with yellow RCA jacks:

• If an aftermarket backup camera is desired to be displayed onto the touchscreen display, connect the Yellow RCA jack labeled “Rearview camera”, to the Yellow RCA jack.

• Disregard the Yellow RCA jack labeled “AUX video”, it will not be used in this application.

REV. 11/30/2018 INST99-8163

Page 8

I N STA L L AT I O N

It is highly advisable to read the following steps beforehand, to ensure a clear understanding of what is to be expected. The following steps must be done in the order that they are numbered.

With the vehicle completely off:

1. Connect the

2. Connect the

harness

before step 1 from the Programming section. This is a timed process.

3. Connect the

4. Connect the a. Connect the harness to the 12-pin and 14-pin harnesses in the vehicle. b. Connect the harness into the c. Connect the harness into port “D” in the touchscreen display.

5. Disregard port “E”, it will not be used in this application.

6. Port “F” is an update port for future ﬁrmware upgrades.

7. Locate the factory antenna connector in the dash and complete all necessary connections

to the radio. Use the the aftermarket radio.

16-pin harness with stripped leads 8163 harness

into port “A” in the touchscreen display. But do not install this harness until exactly

4-pin harness with yellow RCA jacks airbag-indicator/hazard/passenger-seatbelt harness:

to the wiring harnesses in the vehicle. Then insert the

airbag/seatbelt indicator.

antenna adapter

into port “B” in the touchscreen display.

8163

into port “C” in the touchscreen display.

provided to adapt the factory antenna connector to

Note: DO NOT CONNECT!

1.800.221.0932 | MetraOnline.com

Page 9

FINAL ASSEMBLYPROGRAMMING

Attention! If the interface loses power for any reason, the following steps will need to be performed again.

1. Refer to step 2 from the “Installation” section.

2. Start the vehicle.

3. Program the kit:

a. Once the touchscreen display loads up, select the vehicle type; “Lexus IS”.

b. Wait until the radio comes on, and the touchscreen display shows “SWC Conﬁgured*”.

This process may take up to 3 minutes.

Note: If the touchscreen display does not load up, or the radio doesn’t come on within 3

minutes, and/or the touchscreen display does not show “SWC Conﬁgured*”, turn the vehicle off and disconnect the 8163 harnesses from port “A” in the touchscreen display. Check all the connections, reconnect the harness into the touchscreen display, and then try again.

4. Cycle the key off, then back on. If the driver’s door is closed, open and close the door.

5. Test all functions of the installation for proper operation, before reassembling the dash.

1. Secure the completed assembly into the dash using the factory hardware.

2. Reassemble the dash in reverse order of disassembly to complete the installation.

REV. 11/30/2018 INST99-8163

Page 10

Climate Control Screen

TOUCHSCREEN DISPLAY OPERATION

• This is the climate control screen which will be displayed on the touchscreen display. This is considered the main screen.

• The upper right tab with the gear icon will take you to the Conﬁguration Settings screen.

• The Dimmer button will control the illumination intensity: LOW/HIGH

• The climate controls will function in the same manner that they did with the factory climate controls.

Continued on the next page

1.800.221.0932 | MetraOnline.com

Page 11

Conﬁguration Settings screen

TOUCHSCREEN DISPLAY OPERATION (CONT.)

• Backlight

• Four slide bars control the color of the buttons and the back-light intensity:

Red / Green / Blue / Backlight

• Steering Wheel Controls

• Remap Buttons – For remapping the steering wheel control buttons

• Dual Assign – For dual assigning the steering wheel control buttons (long button press)

• Select Radio – For auto detecting the radio, or changing the radio type

• System Conﬁguration

• About - Information regarding the software in the kit

• Digital Amp Gain - For adjusting the output gain to the ampliﬁer

REV. 11/30/2018 INST99-8163

Page 12

STEERING WHEEL CONTROL SETTINGS

Remap Buttons Dual Assign

• The interface has the ability to change the button assignment for the steering wheel control audio buttons, except Volume-Up and Volume-Down. Follow the prompts on the touchscreen display to remap the steering wheel control audio button(s) to your liking.

Note: The aftermarket radio may not have all of these commands. Please refer to the

manual provided with the radio, or contact the radio manufacturer, for speciﬁc commands recognized by that particular radio.

• The interface has the capability to assign two functions to a single button, except Volume-Up and Volume-Down. Follow the prompts on the touchscreen display to program the button(s) to your liking.

Note: Seek-Up and Seek-Down come programmed as Preset-Up and Preset-Down

for a long button press.

1.800.221.0932 | MetraOnline.com

Page 13

STEERING WHEEL CONTROL SETTINGS

Select Radio

• To show which brand radio is “auto detected” to the interface, press the Autodetect button. The radio detected will have a ﬁlled in circle. If the incorrect radio is shown, select the proper radio.

• Following is a list of radio manufacturers that the interface presently acknowledges. Others may be added at a later date. Universal “2 or 3 wire” radios can show up as any of these radio manufacturers.

(CONT.)

* Note: If the interface shows an Alpine radio, and you do not have an Alpine radio, that means the interface does not detect a radio connected it, i.e., an open connection. Verify that the 3.5mm jack is connected to the correct steering wheel jack/wire in the radio.

** Note: The AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must be updated to rev. 2.1.4 or higher through www.parrot.com.

† Note: If you have a Clarion radio and the steering wheel controls do not work, change the radio type to the other Clarion radio type; same for Eclipse.

‡ Note: If you have a Kenwood radio and the touchscreen display shows a JVC radio, change the radio type to Kenwood.

Eclipse (Type 1) † Kenwood ‡ Clarion (Type 1) † Sony / Dual JVC

Pioneer/Jensen Alpine * Visteon Valor

Clarion (Type 2) † Metra OE Eclipse (Type 2) † LG

Parrot ** XITE Philips JBL

REV. 11/30/2018 INST99-8163

Page 14

1.800.221.0932 | MetraOnline.com

Page 15

REV. 11/30/2018 INST99-8163

Page 16

INSTALLATION INSTRUCTIONS

99-8163

If you are having difﬁculties with the installation of this product, contact our Tech Support line either by phone at 1-800-253-TECH, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certiﬁed technicians

Metra. The World’s Best Kits.