Page 1
INSTALLATION INSTRUCTIONS FOR PART 99-8150
APPLICATIONS
LEXUS ES SERIES
1992-1996
KIT FEATURES
• DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
A) Radio Housing • B) Trim Plate • C) Mounting Brackets • D) ISO Brackets • E) (6) Phillips Screws
KIT COMPONENTS
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
1-800-221-0932
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORA
TION
www.metr
aonline.com
99-8150
B
D
C
E
Page 2
Dash Disassembly
-
Lexus ES Series 1992-1996 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Kit
Assembly
- DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . 3
- ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . 4
Final
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
TABLE OF CONTENTS
99-8150
*Note:
Refer also to the instructions included with the aftermarket radio.
Page 3
99-8150 DASH DISASSEMBLY
LEXUS ES SERIES 1992-1996
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove the plastic trim
piece below the factory radio and
remove (2) Phillips screws exposed
underneath. (
Figure A)
2
Using a small flat blade screwdriver
release the clips securing the a/c vent
assembly and remove the assembly.
(Figure B)
3
Remove (2) Phillips screws inside of
vent cavity.
(Figure B)
4
Pull the climate control/radio assembly from the dash and disconnect the
wiring. (
Figure C)
5
Remove (2) Phillips screws and (4)
bolts per side to remove factory
brackets from climate controls and
radio.
6
Continue to kit assembly.
A
B
C
Page 4
99-8150 KIT PREPARATION
2
Install the mounting brackets to the
radio housing with (6) Phillips
Screws supplied. (
Figure A)
1
Install the factory climate controls
into the assembled radio housing
and bracket assembly using the
screws from disassembly. (
Figure A)
2
Continue to kit assembly.
LEXUS ES SERIES 1992-1996
DIN MOUNT RADIO PROVISION WITH POCKET
ISO MOUNT RADIO PROVISON WITH POCKET
A
Page 5
99-8150 KIT ASSEMBLY
3
Slide the DIN cage into the radio
housing and secure by bending the
metal locking tabs outward
(Figure A)
1
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure A)
2
Continue to final assembly.
LEXUS ES SERIES 1992-1996
DIN MOUNT RADIO PROVISION WITH POCKET
Note: Refer also to the instructions included with the aftermarket radio.
A
Page 6
99-8150 KIT ASSEMBLY
4
Mount the ISO brackets to the radio
using the screws supplied with the
radio.
(Figure A)
1
Slide the radio into the radio housing
until the ISO brackets snap into place.
(Figure A)
2
Snap the trim plate onto the front of
the radio housing.
(Figure A)
3
NO
TE:
To remove the mounted aftermarket radio, unclip and remove the
ISO trimplate. Using a small flat blade
screwdriver, disengage the side clips
securing the ISO brackets to the
Radio Housing.
(Figure B)
Continue to final assembly.
LEXUS ES SERIES 1992-1996
ISO MOUNT RADIO PROVISON WITH POCKET
Note: Refer also to the instructions included with the aftermarket radio.
A
B
Page 7
99-8150 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+)
. . . . . . . . . . . . .
Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
5
Page 8
99-8150 INSTRUCTIONS
1-800-221-0932
REV. 07/28/10 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-8150
www.metraonline.com
Loading...