Metra Electronics 99-7875T, 99-7875 User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-7875/99-7875T

APPLICATIONS

Honda Accord 2008-2010

(For Non-Navigation models with Dual Zone Climate controls)

Honda Accord Crosstour 2010

99-7875/99-7875T

KIT FEATURES

• Painted To Match Factory Dash
99-7875=Charcoal, 99-7875T=Taupe

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets

• E) Double DIN Trim Plate • F) Pocket

B

A

E

F

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Cutting Tool

WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:

• 70-1729 - Honda harness 2008-up

• 70-1730 - Honda amp interface harness 2008-up
Antenna Adapter:

• 40-HD10 - Honda antenna adapter 2005-up

TOOLS REQUIRED:

1-800-221-0932

© COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION

C

D

www.metraonline.com

99-7875/99-7875T DASH DISASSEMBLY

HONDA ACCORD 2008-10 / CROSSTOUR 2010

Disconnect the negative battery ter-

1

minal to prevent an accidental short
circuit.

2

Unclip and remove the trim panel
from above the glove box at the right
side of the factory radio. (

3

Unclip and remove the trim panel at
the left side of the factory radio.
(

Figure B)

4

Remove the (2) Phillips screws from
the left and right side of the of the
factory radio. (

5

Unclip and remove the top of the cen­ter console including the cup holders.
(

Figure D)

6

Remove (2) Phillips screws at the bot­tom edge of the pocket assembly.
(

Figure E)

Figure C)

Figure A)

A

B

C

Remove (2) Phillips screws facing up

7

inside of the pocket below the factory
radio. (

Figure F)

8

Unclip and remove the pocket assem­bly. (

Figure G)

Continue on page 2.

E

D

1

99-7875/99-7875T DASH DISASSEMBLY

HONDA ACCORD 2008-10 / CROSSTOUR 2010

9

Remove (2) Phillips screws facing up
on the bottom of the factory radio.
(

Figure H)

10

Unclip the factory radio assembly.
Unplug and remove the radio assem-

Figure I)

bly. (

11

Remove (6) Phillips screws securing
the climate controls to the factory
radio assembly and remove the con­trols from the assembly. (Retain the
screws and climate controls for re­use during kit preparation.)

12

Remove (4) Phillips screws securing
the a/c vents to the factory radio
assembly and remove the a/c vent
from the assembly. (Retain the
screws and a/c vents for re-use dur­ing kit preparation.)

F

G

13

Unclip and remove the hazard
switch/passenger air bag light
assembly. (Retain the hazard
switch/passenger air bag light
assembly for re-use during kit prepa­ration.)

14

Remove (4) Phillips screws securing
trim panel at the bottom edge of the
factory radio assembly and remove
the trim panel. (Retain the screws
and trim panel for re-use during kit
preparation.)

15

Remove (9) clips from the back of the
factory radio assembly. (Retain the
clips for re-use during kit prepara­tion.)

Continue to kit preparation.

H

I

2

99-7875/99-7875T KIT PREPARATION

PAS

SENGER

AIRBAG

HONDA ACCORD 2008-10 / CROSSTOUR 2010

Snap the hazard switch/passenger air

1

bag light assembly into the radio
housing from front. (

2

Secure the a/c vents into the radio

Figure A)

housing using the factory hardware
from rear. (

3

Secure the climate controls into the

Figure B)

radio housing using the factory hard­ware from rear. (

4

Secure the trim panel onto the radio

Figure C)

housing using the factory hardware.
(

Figure D)

5

Attach the clips to the back of the
radio housing. (

Figure E)

Continue to kit assembly.

E

A

B

C

D

3

99-7875/99-7875T KIT ASSEMBLY

DIN MOUNT RADIO PROVISION WITH POCKET

*Note: Refer also to the instructions included with the aftermarket radio.

A

1

Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward.

2

Slide the aftermarket radio into the
DIN cage until it snaps into place.

(Figure B)

3

Snap the pocket into the radio housing.

(Figure C)

Continue to final assembly.

(Figure A)

B

4

C

99-7875/7875T KIT ASSEMBLY

ISO MOUNT RADIO PROVISION WITH POCKET

*Note: Refer also to the instructions included with the aftermarket radio.

1

Mount the ISO Brackets to the radio
using the screws supplied with the

(Figure A)

radio.

2

Slide the radio into the Radio Housing
until it snaps into place.

3

Snap the Trim Plate onto the front of
the Radio Housing.

4

Snap the Pocket into the Radio
Housing.

(Figure C)

(Figure B)

(Figure C)

A

Continue to final assembly.

B

C

5

99-7875/99-7875T KIT ASSEMBLY

DOUBLE DIN/STACKED ISO MOUNT UNITS PROVISION

*Note: Refer also to the instructions included with the aftermarket radio.

1

Cut and remove the center bar from
the Radio Housing.

2

Snap the Double DIN brackets to the
inside edge of the Radio Housing.

(Figure B)

3

Slide the Double DIN or stacked ISO
mount units into the bracket/radio
housing assembly and secure the
unit(s) to the assembly using the
screws supplied with the unit(s).

(Figure C)

4

Snap the Double DIN trim plate onto
the front of the Housing/Radio assem­bly.

(Figure C)

(Figure A)

A

B

Continue to final assembly.

C

6

99-7875/99-7875T FINAL ASSEMBLY

FINAL ASSEMBLY

A

(A) Strip wire ends back 1/2"

B

B) Twist ends together

C) Solder

C

D

Locate the factory wiring harness in the dash. Metra recommends using the

1

proper mating adapter and making connections as shown. (Isolate and individ­ually tape off the ends of any unused wires to prevent electrical short circuit.)

2

Re-connect the negative battery terminal and test the unit for proper operation.

Reassemble radio and dash assemblies in reverse order of disassembly.

3

D) Tape

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and

individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

12V Ignition / Acc . . . . . . . . . . Red

12V Batt / Memory. . . . . . . . . Yellow

Ground. . . . . . . . . . . . . . . . . . Black*

Power Antenna. . . . . . . . . . . . Blue

Amp Turn-On . . . . . . . . . . . . . Blue / White

Amp Ground. . . . . . . . . . . . . . Black / White

Illumination . . . . . . . . . . . . . . Orange

Dimmer . . . . . . . . . . . . . . . . . Orange / White

Right Front (+) . . . . . . . . . . . . Gray

Right Front (-). . . . . . . . . . . . . Gray/ Black

Left Front (+) . . . . . . . . . . . . . White

Left Front (-). . . . . . . . . . . . . . White / Black

Right Rear (+) . . . . . . . . . . . . Violet

Right Rear (-) . . . . . . . . . . . . . Violet / Black

Left Rear (+) . . . . . . . . . . . . . Green

Left Rear (-) . . . . . . . . . . . . . . Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis.

All colors may not be present on all leads due to manufacturer’s specifications.

7

99-7875/7875T

NOTES

8

99-7875/99-7875T

NOTES

9

99-7875/7875T INSTRUCTIONS

1-800-221-0932

REV. 04/21/10 © COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION INST99-7875

www.metraonline.com