Metra Electronics 99-7860 Installation Manual

Page 1
99-7860
1-800-221-0932 • www.metraonline.com
COPYRIGHT© 2002 METRA ELECTRONICS CORPORATION
KIT COMPONENTS
INSTALLATION INSTRUCTIONS
Honda Civic SI 2002
VEHICLE APPLICATIONS
implate
using •
Trimplate •
• ISO Snap in Brackets(2)
Phillips screwdriver
Offset tool
TOOLS REQUIRED
KIT FEATURES
DIN head unit provision with pocket
ISO head unit
provision with pocket
Stacked ISO head
unit provision
Double DIN head unit provision
Questions?
Call the Help Line:
(800)253 TECH
T997860 081302
Page 2
99-7860
1
DASH DISASSEMBLY
1 Disconnect the negative
battery terminal to prevent an accidental short circuit.
2 Remove the shift knob
and unsnap the shifter lever trim panel.
3 Using and offset tool
remove (2) lower bolts securing the center panel.
4 Unsnap and remove the
dash trim bezel and disconnect the wiring.
5 Remove (3) phillips
screws securing the climate control pod to the back of the dash trim bezel and remove the pod.
6 Remove (4) phillips
screws from each side securing the factory head unit and pocket to the bracket assembly and remove.
NOTE: Removing the glove
box and the driver's side lower trim panel may be necessary when removing the shifter level trim panel when not using an offset tool.
99-7860 • Honda Civic SI 2002
99-7860
TABLE OF CONTENTS
Dash Disassembly
• Kit Features
• DIN Head Unit Provision with Pocket Assembly
• ISO Head Unit Provision with Pocket Assembly
• Double DIN Head Unit Provision Assembly
• Stacked ISO Head Unit Provision Assembly
• Final Assembly
Page 3
99-7860
3
Align the holes in the ISO Snap-In
Brackets with the holes in the head
unit and mount the brackets to the head unit with the screws supplied
with the unit.
See figure A
Slide the head unit/bracket assem­bly into the radio opening until the
side clips engage.
See figure B
Snap the ISO trimplate over the
head unit.
See figure C
ISO HEAD IUNIT PROVISION WITH POCKET
1
3
2
99-7860 • Honda Civic SI 2002
NOTE: To remove the mounted head unit,
unclip and remove the ISO Trimplate. Using
a small flat-blade screwdriver, disengage
the side clips securing the ISO Snap In
Brackets to the housing/pocket assembly.
A
B
C
Assembled Kit
Snap the housing assembly into
the dash trim bezel.
4
99-7860
2
DIN HEAD UNIT PROVISION WITH POCKET
Slide the DIN cage into the radio opening of the Housing and secure by bending the metal locking tabs down.
See figure A
Slide the DIN unit into the cage until it is secure.
See figure B
1
2
A
B
99-7860 • Honda Civic SI 2002
Assembled Kit
Snap the housing assembly into the dash trim bezel.
3
Page 4
5
Snap the Double DIN Trimplate
over the head unit.
See figure B
STACKED ISO HEAD UNIT PROVISION
6
5
A
B
Align the holes on the factory
bracket assembly with the holes on
the aftermarket ISO head units and
mount with the screws supplied
with the units.
See figure A
99-7860 • Honda Civic SI 2002
Assembled Kit
99-7860
4
DOUBLE DIN HEAD UNIT PROVISION
1
2
3
Align the holes on the factory bracket assembly with the holes on the aftermarkert Double DIN head unit and mount with the screws supplied with the unit.
See figure A
Cut and remove the center rib (SHADED) from the Double DIN
Trimplate.
See figure B
Snap the Double DIN Trimplate over the head unit.
See figure C
99-7860 • Honda Civic SI 2002
A
B
C
Assembled Kit
Page 5
99-7860
6
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
FINAL ASSEMBLY
A
B
C
D
99-7860 • Honda Civic SI 2002
A
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adaptor (70-1721) and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit).
See figure A
1
Re-connect the battery terminal and test the unit for proper operation.
2
Reassemble dash in the reverse order of page 1 in the Dash Disassembly.
3
Loading...