Page 1
INSTALLATION INSTRUCTIONS FOR PART 99-7516B
APPLICATIONS
Mazda CX9
2007-2009
99-7516B
KIT FEATURES
• DIN Head Unit Provision with Pocket
• ISO DIN Head Unit Provision with Pocket
• Double DIN Head Unit Provision
• ISO Stacked Head Unit Provision
• Painted matte black to match factory
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket
B
C
A
E
WIRING AND ANTENNA CONNECTIONS
• MZTO-01 - Mazda Amp Integration Harness 2007-Up
• 70-7903T - Mazda service harness 2007-up
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2007-2009 METRA ELECTRONICS CORPORATION
(Sold Separately)
www.metraonline.com
D
F
Page 2
99-7516B
K
NOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
TABLE OF CONTENTS
Dash Disassembly
-
Mazda CX9 2007-2009 . . . . . . . . . . . . . . . . . . . . . .
Kit Assembly
. . . . . . . . 1
- DIN Head Unit Provisions with Pocket . .
- ISO DIN Head Unit Provisions with Pocket
. . . . . . . . . . . . . . . . . . . . . .2
. . . . . . . . . . . . . . . . . . . . . .3
- Double DIN Head Unit Provision/Stacked ISO DIN Head Unit Provision. .
*Note:
Refer also to the instructions included with the aftermarket radio.
4
Page 3
99-7516B DASH DISASSEMBLY
7
3
7
3
883
0FM1ch1
VOL
PUSH POWER
TUNE
PUSH AUDIO
L
OAD/
SOURCE
SCAN
I
NFO
R
ETURN
M
ENU
DISP
MAP
VOICE
S
EEK
TRACK
PUSH
A
UTO ON
PUSH
OFF
PUSH
DUAL
PASS
A/C A/C
L
O
HI
F
RONT
R
EAR
M
ODE
OUTSIDE
TEMP
PP
RR
NN
D
D
M
M
73
73
883
0FM1ch1
V
OL
PUSH POWER
TUNE
PUSH AUDIO
LOAD/
SOURCE
SCAN
INFO
RETURN
MENU
DISP
MAP
VOICE
SEEK
TRACK
PUSH
AUTO ON
PUSH
OFF
PUSH
DUAL
PASS
A/C A/C
LO
HI
FRONT
REAR
MODE
OUTSIDE
TEMP
P
P
RR
N
N
D
D
M
M
73
73
883
0FM1ch1
VOL
PUSH POWER
TUNE
PUSH AUDIO
LOAD/
SOURCE
SCAN
INFO
RETURN
MENU
DISP
MAP
VOICE
SEEK
TRACK
PUSH
AUTO ON
PUSH
OFF
PUSH
DUAL
PASS
A/C A/C
LO
HI
FRONT
REAR
MODE
OUTSIDE
TEMP
VOL
PUSH POWER
TUNE
PUSH AUDIO
LOAD/
I
NFO
RETURN
MAP
VOICE
SEEK
TRACK
73
73
883
0FM1ch1
PUSH
AUTO ON
PUSH
OFF
PUSH
DUAL
PASS
A/C A/C
LO
HI
FRONT
REAR
MODE
OUTSIDE
TEMP
MAZDA CX9 2007-2009
Disconnect the negative battery
1
terminal to prevent an accidental
short circuit.
2
Unclip and remove both side panels
from center radio trim panel.
(Figure A)
Unclip and remove the shifter trim
3
panel.
(Figure B)
Remove (1) Phillips screw from the
4
accessory socket trim panel then
unclip and remove the panel.
Remove (2) Phillips screws from the
5
radio trim panel.
Unclip and remove the entire radio
6
(Figure D)
(Figure C)
trim panel including the a/c controls.
(Figure D)
Remove (4) Phillips screws securing
7
the radio.
A
B
Continue to kit assembly.
E
C
1
Page 4
99-7516B KIT ASSEMBLY
DIN HEAD UNIT PROVISION WITH POCKET
*
Note: Refer also to the instructions included with the aftermarket radio.
Locate the factory wiring harness in
1
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down.
3
Snap the pocket into the bottom
opening of the radio housing.
(Figure B)
4
Slide the aftermarket head unit into
the cage and secure.
(Figure A)
(Figure C)
A
B
Reassemble dash in reverse order of
5
disassembly.
C
2
Page 5
99-7516B KIT ASSEMBLY
ISO DIN HEAD UNIT PROVISION WITH POCKET
*
Note: Refer also to the instructions included with the aftermarket radio.
Locate the factory wiring harness in
1
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit.
3
Snap the pocket into the bottom
opening of the radio housing.
4
Slide the head unit into the radio
opening until the side clips engage.
(Figure C)
Snap the Trim plate into the Radio
5
Housing.
(Figure A)
(Figure B)
(Figure C)
A
B
6
Reassemble dash in reverse order of
disassembly.
C
3
Page 6
99-7516B KIT ASSEMBLY
DOUBLE DIN HEAD UNIT PROVISION/
STACKED ISO DIN HEAD UNIT PROVISION
*
Note: Refer also to the instructions included with the aftermarket radio.
Locate the factory wiring harness in
1
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2
Cut and remove the center bar from
the radio housing.
3
Snap the Double DIN brackets to the
inside edge of the Double DIN trim
(Figure B)
plate.
4
Slide the Double DIN head unit or
stacked ISO head units into the
bracket/radio housing assembly and
secure the Double DIN head unit or
stacked ISO head units to the
assembly using the screws supplied
with the radio.
(Figure A)
(Figure C)
A
B
5
Snap the double DIN trim plate into
the radio housing.
6
Reassemble dash in reverse order of
disassembly.
(Figure C)
C
4
Page 7
99-7516B
NOTES
5
Page 8
99-7516B INSTRUCTIONS
1-800-221-0932
REV. 08/24/09 © COPYRIGHT 2007-2009 METRA ELECTRONICS CORPORATION INST99-7516B
www.metraonline.com
Loading...