Metra Electronics 99-7511S Installation Manual

Page 1
INSTALLATION INSTRUCTIONS FOR PART 99-7511S
99-7511S
APPLICATIONS
Mazda 6 2009
KIT FEATURES
• DIN Radio Provision
• ISO Mount Radio Provision
• Stacked ISO Mount Radio Provision
• Painted To Match Silver Factory Dash
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket • G) Filler Trim Panel • H) (2) #3 3/8” Phillips Screws
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
1-800-221-0932
© COPYRIGHT 2009 METRA ELECTRONICS CORPORA
TION
www.metr
aonline.com
B
D
E
G
C
TOOLS REQUIRED:
F
H
Page 2
Dash Disassembly
-
Mazda 6 2009 ................................
. . . . . . 1
Kit Assembly
- DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
- ISO Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- Double DIN /Stacked ISO Mount Unit(s) Provision . . . . . . . . . . . . . . . . 4
Final
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
TABLE OF CONTENTS
99-7511S
*Note: Refer also to the instructions included with the aftermarket radio.
Page 3
99-7511S DASH DISASSEMBLY
MAZDA 6 2009
A
B
C
D
1
1
Unclip and remove the trim panel above the glove box and down the right side of the center console. (
Figure B)
Disconnect the negative battery terminal to prevent an accidental short circuit.
3
Unclip and remove the cup holder/parking brake trim panel. (
Figure A)
2
Unclip and remove the trim panel next to the key switch and down the left side of the center console. (
Figure B)
4
Unclip and remove the trim panel surrounding the climate controls and the shifter lever. (
Figure C)
5
Unclip and remove the vent panel above the radio. (
Figure D)
6
Remove (4) screws securing the factory radio. Unplug and remove the radio.
7
Continue to kit preparation
Page 4
99-7511S KIT ASSEMBLY
2
REAR OF RADIO HOUSING
FILLER TRIM PANEL
A
B
C
D
DIN RADIO PROVISION
Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward.
(Figure B)
2
Attach the filler trim panel to the back of the radio housing at the bottom edge.
(Figure A)
1
Slide the aftermarket radio into the DIN cage until it snaps into place.
(Figure C)
3
Snap the pocket into the the bottom opening of the radio housing.
(Figure D)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Page 5
99-7511S KIT ASSEMBLY
3
B
A
REAR OF RADIO HOUSING
FILLER TRIM PANEL
C
D
ISO MOUNT RADIO PROVISION
Mount the ISO Brackets to the radio using the screws supplied with the radio.
(Figure B)
2
Slide the radio into the radio housing until it snaps into place.
(Figure C)
3
Snap the Trim Plate onto the front of the Radio Housing.
(Figure C)
4
Snap the pocket into the bottom open­ing of the radio housing.
(Figure D)
5
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Attach the filler trim panel to the back of the radio housing at the bottom edge.
(Figure A)
1
Page 6
99-7511S KIT ASSEMBLY
4
DOUBLE DIN/STACKED ISO MOUNT
UNIT(S) PROVISION
Cut and remove the center bar from the Radio Housing.
(Figure B)
2
Snap the Double DIN brackets to the inside edge of the Radio Housing.
(Figure C)
3
Slide the Double DIN or stacked ISO mount unit(s) into the bracket/radio housing assembly and secure to the assembly using the screws supplied with the unit(s). Snap the DDIN Trim Plate onto the front of the Radio Housing.
(Figure D)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
REAR OF RADIO HOUSING
FILLER TRIM PANEL
B
C
D
Attach the filler trim panel to the back of the radio housing at the bottom edge.
(Figure A)
1
Page 7
99-7511S FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ­ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground
. . . . . . . . . . . . . .
Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-)
. . . . . . . . . . . . .
Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
Enjoy your newly installed radio!
5
Page 8
99-7511S INSTRUCTIONS
1-800-221-0932
Rev. 01/13/09 © COPYRIGHT 2009 METRA ELECTRONICS CORPORATION NST99-7511S
www.metraonline.com
Loading...