INSTALLATION INSTRUCTIONS FOR PART 99-7424
APPLICATIONS
Nissan Titan 2008-11
99-7424
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Painted To Match Factory Dash
KIT COMPONENTS
A) Single DIN Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) Trim Panel
• E) Two Sided Tape (Not Shown)
B
A
Harness & Antenna Connections (sold separately)
• 70-7550 - Nissan Harness 95-up
TOOLS REQUIRED:
Torx T-10 Driver • Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
C
D
www.metraonline.com
TABLE OF CONTENTS
Dash Disassembly
99-7424
Nissan Titan 2008-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . 2
Kit Assembly
- DIN Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . .4
Final Assembly
*Note:
Refer also to the instructions included with the aftermarket radio.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
99-7424 DASH DISASSEMBLY
NISSAN Titan 2008-11
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
2
Unclip the entire dash panel including
the radio and climate controls. Unplug
and remove the panel.
3
Remove (4) Phillips screws securing
the radio chassis. Unplug and remove
the chassis.
Remove (4) T-10 Torx screws securing
4
the climate controls to the dash panel
and remove the controls from the
panel. (Retain t
controls for re-use during kit preparation.)
(Figure B)
he screws and climate
(Figure C)
(Figure A)
A
B
5
Remove (2) T-10 Torx screws securing
the passenger air bag status light
assembly to the dash panel and
remove the light from the panel.
(Retain the screws and light for reuse during kit preparation.)
The small round Airbag sticker
NOTE:
also needs to be removed from the factory panel and placed onto the 99-7424
radio housing panel. (A round piece of
double-sided tape is provided in case
the factory sticker is not strong
enough.) (Figure C)
Continue to kit preparation
(Figure C)
C
1
99-7424 KIT PREPARATON
NISSAN Titan 2008-11
Attach the climate controls to the Trim
1
Panel using the factory hardware
removed during the dash disassem-
(Figure A)
bly.
2
Attach the passenger air bag status
light assembly to the Trim Panel using
the factory hardware removed during
the dash disassembly. Also, apply to
air bag button the small round airbag
sticker previously removed in Step 5
dash disassembly.
Continue to kit assembly.
(Figure B)
A
B
2
99-7424 KIT ASSEMBLY
DIN RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
Slide the DIN cage into the Single DIN
Radio Housing and secure by bending
the metal locking tabs outward.
2
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure B)
Continue to final assembly.
B
3
99-7424 KIT ASSEMBLY
ISO MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
Mount the ISO Brackets to the radio
using the screws supplied with the
(Figure A)
radio.
2
Slide the radio into the radio housing
until it snaps into place.
3
Snap the Trim plate onto the front of
the Radio Housing.
(Figure B)
(Figure B)
Continue to final assembly.
B
4
99-7424 FINAL ASSEMBLY
FINAL ASSEMBLY
A
(A) Strip wire ends back 1/2"
B
B) Twist ends together
C) Solder
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
1
proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble in reverse order of disassembly using the 99-7424 Trim Panel in
3
place of the f
actory radio trim panel.
D) Tape
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
5
99-7424 INSTRUCTIONS
1-800-221-0932
REV. 11/18/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7424
www.metraonline.com
Loading...