INSTALLATION INSTRUCTIONS FOR PART 99-7319
APPLICATIONS
2004-2006 Kia Amanti
99-7319
KIT FEATURES
• DIN Head Unit Provision
• ISO DIN Head Unit Provision
KIT COMPONENTS
A) Radio Housing B) A/C Control Brackets C) ISO Brackets D) Trim plate
A
Phillips Screwdriver I Small Flat Blade Screwdriver
B
TOOLS REQUIRED:
C
D
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION
99-7319
TABLE OF CONTENTS
Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1, 2
Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 4
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
99-7319
P
R
N
D
E
S
P
2004-2006 KIA AMANTI
Disconnect the negative battery
1
terminal to prevent an accidental
short circuit.
2
Unclip and remove panel surrounding shifter including cup holders.
(Figure A)
Remove (2) Phillips screws at base
3
of panel surrounding radio and a/c
controls.
4
Unclip and remove panel surrounding radio and a/c control.
(Figure B)
DASH DISASSEMBLY
A
B
(Figure C)
C
1
99-7319
V
OL
L
OAD
2 Phillips screws on each side
2004-2006 KIA AMANTI
5
Remove (6) Phillips screws securing
radio and a/c control.
6
Remove (4) Phillips screws securing
factory a/c control to bracket assem-
(Figure E)
bly.
(Figure D)
DASH DISASSEMBLY
D
E
2
99-7319
2004-2006 KIA AMANTI
DIN HEAD UNIT PROVISION
Attach the corresponding a/c control
1
bracket to the factory a/c control
using the factory hardware.
Note: The radio housing must be
installed first before the a/c control.
Slide the DIN cage into the radio
1
housing and secure by bending the
metal locking tabs down.
(Figure B)
KIT ASSEMBLY
A
(Figure A)
B
Slide the aftermarket head unit into
2
the cage and secure.
(Figure C)
C
3
99-7319
2004-2006 KIA AMANTI
ISO DIN HEAD UNIT PROVISION
Attach the corresponding a/c control
1
bracket to the factory a/c control
using the factory hardware.
Note: The radio housing must be
installed first before the a/c control.
Mount the ISO bracket to the head
1
unit with screws supplied with the
(Figure B)
unit.
KIT ASSEMBLY
A
(Figure A)
B
Slide the head unit into the radio
2
opening until the side clips engage.
(Figure C)
Snap the trim plate into the radio
3
housing.
(Figure C)
C
4
99-7319
FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
C
D
1
2
3
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown.
(Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly
installing the radio housing first and then the a/c control.
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
12V Batt / Memor
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
y . . Yellow
Right Front (+) . . . . . Gray
Right Front (-) . . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
5
99-7319 INSTRUCTIONS
1-800-221-0932 www.metraonline.com
REV. 06/19/2007 © COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION INST99-7319
Loading...