Page 1
INSTALLATION INSTRUCTIONS FOR PART 99-5814
APPLICATIONS
See application list inside
Ford/Mazda multi-kit
2008-Up
99-5814/99-5814S
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
Painted to match factory dash:
99-5814=Black, 99-5814S=Silver
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket • G) (2) Spare Radio Housing Panel Clips
A
F
B
G
C
D
WIRING & ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• XSVI-5520-NAV Ford Interface 2006-up
• 70-5522-Ford Sub harness 2003-up
Antenna Adapter:
• 40-CR10 Chrysler/GM antenna adapter 2002-up
• AFSI-02 if equipped w/ sync
E
TOOLS REQUIRED
Cutting Tool • Phillips Screwdriver • Socket Wrench
METRA. THE WORLD’S BEST KITS.™
1-800-221-0932
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
metraonline.com
Page 2
99-5814
Applications
Ford
Escape 2008-Up
Mercury
Mariner 2008-Up
Mazda
Tribute 2008-Up
Table of Contents
Dash Disassembly
- All Vehicles.....................................................................................................................1,2
Kit Assembly
- Kit Preparation..................................................................................................................2
- DIN Radio with Pocket Provison........................................................................................2
- ISO Mount Radio with Pocket Provison..............................................................................2
- Double DIN Radio Provison................................................................................................2
- Stacked ISO Mount Units Provison.....................................................................................2
Caution
Metra recommends disconnecting the negative battery terminal before beginning any
installation. All accessories, switches, and especially air bag indicator lights must be
plugged in before reconnecting the battery or cycling the ignition.
*NOTE: There are (2) extra radio housing panel clips included with the kit in case
removal of the kit is necessary at any time.
*NOTE: Refer also to the instructions included with the aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Page 3
99-5814
Dash Disassembly
All Vehicles
1. Unclip and remove the a/c vent panel
above the radio. (Figure A)
2. Remove the (2) 7 MM screws exposed
at the top of the factory radio panel.
(Figure B)
3. Unclip the accessory socket/switch/aux
input panel below the radio. Unplug
and remove the panel. (Figure C)
Continue on page 2
(Figure A)
1
(Figure B)
(Figure C)
Page 4
99-5814
Dash Disassembly
All Vehicles
4. Remove the (2) 7 MM screws exposed
at the bottom of the factory radio panel.
(Figure D)
5. Slide radio out and remove (1) 8mm bolt
from the right side securing the ground
strap to the radio brackets. Unplug and
remove the radio.
6. Remove (4) Torx screws securing the
climate controls to the factory radio
panel. Remove the climate controls and
retain them with the factory screws for
use during kit assembly. (Figure E)
Continue to kit assembly
(Figure A)
REAR OF RADIO
2
REAR CLIMATE CONTROL
(Figure B)
Page 5
99-5814
Kit Preparation
1. Attach the climate control to the radio
housing using the factory hardware
removed in step 7 of dash disassembly.
(Figure A)
Note: There are (2) extra radio housing
panel clips included with the kit in case
removal of the kit is necessary at any
time. (Figure B)
Continue to kit assembly
(Figure A)
TWO EXTRA
RADIO HOUSING
RETAINING CLIPS
(Figure B)
3
Page 6
99-5814
DIN Mount Radio Provision
With Pocket
1. Slide the DIN cage into the radio
housing and secure by bending the
metal locking tabs outward. (Figure A)
2. Slide the aftermarket radio into the
DIN cage and until it snaps into place.
(Figure B)
3. Snap the pocket into the radio housing.
(Figure C)
Reassemble dash in reverse order of
disassembly.
(Figure A)
4
(Figure B)
(Figure C)
Page 7
99-5814
ISO Mount Radio Provision
With Pocket
1. Mount the ISO Brackets to the radio
using the screws supplied with the
radio. (Figure A)
2. Slide the radio into the radio housing
until it snaps into place. (Figure B)
3. Snap the trim plate onto the front of the
Radio Housing. (Figure B)
4. Snap the Pocket into the radio housing.
(Figure C)
Reassemble dash in reverse order of
disassembly.
(Figure A)
5
(Figure B)
(Figure C)
Page 8
99-5814
Double DIN Radio Provision
1. Cut and remove the center bar from the
radio housing. (Figure A)
2. Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
3. Slide the Double DIN radio into the DDIN
bracket/radio housing assembly and
secure the radio to the assembly using
the screws supplied with the radio.
(Figure C)
3. Snap the Double DIN trim plate onto the
front of the radio/housing assembly.
(Figure C)
Reassemble dash in reverse order of
disassembly.
(Figure A)
6
(Figure B)
(Figure C)
Page 9
99-5814
Stacked ISO Mount Units Provision
1. Cut and remove the center bar from the
radio housing. (Figure A)
2. Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
3. Slide the stacked ISO mount units into
the bracket/housing assembly and
secure the units to the assembly using
the screws supplied with the units.
(Figure C)
4. Snap the Double DIN trim plate onto the
front of the radio/housing assembly.
(Figure C)
Reassemble dash in reverse order of
disassembly.
(Figure A)
7
(Figure B)
(Figure C)
Page 10
INSTALLATION INSTRUCTIONS FOR PART 95-5817
REV. 10/05/11
METRA. THE WORLD’S BEST KITS.™
1-800-221-0932
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
metraonline.com
Loading...