INSTALLATION INSTRUCTIONS FOR PART 99-5719INSTALLATION INSTRUCTIONS FOR PART 99-5719
APPLICATIONS
FORD TAURUS
2004 - 2007
99-5719
KIT FEATURES
• ISO & DIN Head Unit Provision w/ Pocket
• DDIN Head unit provisions
• Integrated auto climate controls and display
• Integrated passenger airbag light
• Painted Scratch Resistant Matte Black
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Pocket
• E) DDIN Brackets • F) DDIN Trim Plate • G) In-Car Temp Sensor Housing • H) Harness Extension
REV. 1/20/2010
METRA. THE WORLD’S BEST KITS.™
1-800-221-0932 metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
B
A
F
C
D
G
TOOLS REQUIRED
• Radio Removal Tool (Metra Part #86-5618) • Phillips Screwdriver
• Panel Removal Tool • Socket Set • Cutting Tool or File • T10 Torx Screwdirver
METRA. THE WORLD’S BEST KITS.™
1-800-221-0932 metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
E
H
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
99-5719 99-5719
TABLE OF CONTENTS
DASH DISASSEMBLY
• FORD TAURUS 2004 - 2007 . . . . . . . . . . . 1
KIT PREPARATION
• FORD TAURUS 2004 - 2007 . . . . . . . . . . . 2
KIT ASSEMBLY
• FORD TAURUS 2004 - 2007 . . . . . . . . . 3-6
*NOTE: This product has software that can be flashed via the AXXESS
USB-CAB cable and AXXESSINTERFACE.COM. Please contact the
Metra tech support team if you feel this product is not performing
properly.
*NOTE: Refer Also to the instructions included with the aftermarket radio.
NOTES
Metra recommends MECP certified
technicians
99-5719
99-5719 DASH DISASSEMBLY
NOTES
FORD TAURUS 2004- 2007
Disconnect the negative
1
battery terminal to prevent an
accidental short circuit.
Using Metra’s 86-5618, pull
2
the factory radio/climate
control panel from the dash.
(Fig. A)
Disconnect the audio system
3
connectors, blower motor
switch connector, vacuum
hose harness, a/c damper
door switch connector, and
potentiometer connector.
Remove the panel.
Remove (2) torx-head screws
4
securing the mounting clips to
the sides of the factory
radio/climate control panel
and remove the clips. (Fig. B)
A
B
Mount the clips to the
5
Integrated Mounting Kit with
the same torx-head screws.
1
99-5719 KIT PREPARATION
2
Fig. A
Fig. B
Back
wall
Inside edge
of sub-dash
Inside edge
of sub-dash
Back
wall
(located under
the rear deck)
Fig. A
Fig. B
99-5719
FORD TAURUS 2004- 2007 FORD TAURUS 2004- 2007
Remove the In-Car temp
1
A
AUDIO WIRING
sensor housing from the
back of the factory control
panel. Insert into the included In-Car temp sensor
housing and mount the
assembly under the dash.
Open the trunk, remove (4) popclips from the driver’s side trunk
liner and remove the liner. (see
Fig. A) ocate the factory tuner on
the wall of the trunk and disconnect the speaker and antenna plugs
(it is NOT necessary to remove
Remove the factory rear sup-
2
port in the sub-dash. (Fig. A)
the tuner). (see Fig. B). Plug the
70-5715 into the unit speaker plug
and the antenna extension lead into
the unit antenna plug. Slide the extension harness through the space
in the back seat between the seat
back and seat bottom. Unclip the
rocker trim, tuck the extension harness under the carpet and stretch
the harness to the back of the dash.
(Replace the rocker trim when
completed). Splice the speaker
leads on the extension harness into
the rear of the aftermarket head
unit. Plug the factory wiringharnesses into the switch connectors
(previously mounted in step #2)
and audio connectors on the back
Continue to Kit Assembly
of the Integrated Mounting Kit.
2 7
99-571999-5719
FORD TAURUS 2004- 2007
DDIN/STACKED ISO DIN
HEAD UNIT PROVISION
......... Continued from Pg.5
Snap the double DIN trim
plate into the radio housing.
5
(Fig. B)
Continue to “Audio Wiring”......
B
FORD TAURUS 2004- 2007
DIN HEAD UNIT PROVISION
1
Locate the factory wiring harness in the dash. Metra
recommends using the proper mating adapters (included)
from Metra and AXXESS to
integrate your new radio.
Re-connect the negative battery terminal and test the unit
for proper operation.
Slide the DIN cage into the
2
Radio Housing and secure
by bending the metal locking
tabs down. (Fig. A)
Snap the pocket into the
3
bottom opening of the radio
housing. (Fig. B)
A
B
Slide the aftermarket head
4
unit into the cage and secure. (Fig. B)
Continue to “Audio Wiring”....
6 3
99-571999-5719
FORD TAURUS 2004- 2007 FORD TAURUS 2004- 2007
ISO DIN HEAD UNIT PROVISION
Locate the factory wiring har-
1
ness in the dash. Metra
recommends using the proper
mating adapters (included)
from Metra and AXXESS to
integrate your new radio. Reconnect the negative battery
terminal and test the unit for
proper operation.
Mount the ISO Brackets to the
2
head unit with the screws supplied with the unit. (Fig. A)
Snap the pocket into the bot-
3
tom opening of the radio housing. (Fig. B)
Slide the head unit into the ra-
4
dio opening until the side clips
engage. (Fig. B)
Snap the Trim plate into the
5
Radio Housing.
Continue to “Audio Wiring”....
A
B
DDIN/STACKED ISO DIN
HEAD UNIT PROVISION
Locate the factory wiring har-
1
ness in the dash. Metra
recommends using the proper
mating adapters (included)
from Metra and AXXESS to
integrate your new radio. Reconnect the negative battery
terminal and test the unit for
proper operation.
Cut and remove the center
2
bar from the radio housing.
(Fig.A)
Snap the Double DIN brack-
3
ets to the inside edge of the
Double DIN trim plate.
Slide the Double DIN head
4
unit or stacked ISO head units
into the bracket/radio housing
assembly and secure the Double DIN head unit or stacked
ISO head units to the assembly using the screws supplied
with the radio. (Fig. B)
A
Continued on Pg. 6
4 5
Loading...