Metra Electronics 99-3301 User Manual
ALL VEHICLES
2 3
"L"
"R"
Slide Mounting Brackets ("L" and "R")
into the slots on the sides of the Radio
Housing
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
as indicated.
4 5
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
Re-connect the battery terminal and test the unit
for proper operation. Mount the head unit/kit
assembly to the sub-dash with those screws
previously removed in step #1.
Slide the ISO-DIN head unit into the kit. Align
the holes in the Mounting Brackets with the
holes in the head unit and mount the Brackets
to the head unit with the screws included with
the unit.
REV. 07-29-09
KIT FEATURES
ISO-DIN unit
provisions
CD pocket holds
(2) jewel cases
KIT COMPONENTS
Radio Housing
Mounting
Brackets
TOOLS REQUIRED
Phillips screwdriver
Socket wrench
99-3301
INSTALLA
TION
APPLICATIONS
CAR
BUICK
Century 1997-2005........................................................ 1
LeSabre 1995-2005...................................................... 1
Park Avenue 1995-2005................................................ 1
Regal 1995-2004.............................................................. 6
Rendezvous 2002-200
CHEVROLET
Avalanche 2003-2006................................................. 6
Cavalier 2000-2005..
Express Van 2001-2007............................................... 5
Impala 2000-2005......................................................... 5
Malibu 2001-2003........................................................... 5
Monte Carlo 2000-200
Trailblazer 2002-2007.................................................... 2
Venture 2000-2005..
GMC
Envoy 2002-200
OLDMOBILE
Bravada 1998-200
Silhouette 2000-2004................................................... 5
PONTIAC
Aztec 2001-2005..
Bonneville 2000-2005.................................................. 3
Grand Am 2001-200
Montana 2000-2005
Sunfire 2000-2005
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
Please visit www.metraonline for specific interface
applications
Antenna adapter: • 40-GM10 - GM antenna adapter 88-up
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001-2009 METRA ELECTRONICS CORP.
INSTRUCTIONS
PAGE
7................................................ 6
..................................................... 6
5 ............................................. 5
..................................................... 2
7............................................................ 2
1......................................................... 2
............................................................ 3
5................................................... 4
..................................................... 4
........................................................ 4
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills
by enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 for more information
and take steps toward a better tomorrow.
BUICK Century 1997-2005
BUICK Regal 1995-2000
1
Disconnect
accidental
the
Unsnap
(1)
cluster
entire
unsnap
remove
screws
BUICK LeSabre 1995-2005
Disconnect the negative battery terminal to prevent an
1
accidental
and
from
remove
instrument
radio.
BUICK Park Avenue 1995-1999
1
Disconnect the negative battery terminal to prevent an
accidental short circuit. Unsnap the climate control trim
panel (from door to door) and remove (4) phillips screws
exposed. Pop out the a/c vents and remove (1) phillips
screw exposed in each vent cavity. Unclip the radio trim
bezel and remove. Remove the screws securing the factory
head unit and disconnect the wiring.
the negative battery terminal to prevent an
short circuit. Remove the plastic trim piece to
left of the glove box and (1) phillips screw exposed.
the top edge of the knee bolster panel. Remove
phillips screw from the panel. Remove the ashtray
and (2) phillips screws from each side. Unclip the
dash trim bezel and remove. Open doors and
end caps from each side of dash. Unsnap and
radio/instrument cluster panel. Remove (3)
in order to remove radio.
short circuit. Open drivers door and unsnap
remove dash end cap. Remove (2) phillips screws
underneath steering column cover. Unsnap and
steering column cover. Unsnap and remove
panel. Remove (2) 9/32" screws and remove
1
Disconnect
accidental
the
Unsnap
(1)
cluster
entire
unsnap
remove
screws
the negative battery terminal to prevent an
short circuit. Remove the plastic trim piece to
left of the glove box and (1) phillips screw exposed.
the top edge of the knee bolster panel. Remove
phillips screw from the panel. Remove the ashtray
and (2) phillips screws from each side. Unclip the
dash trim bezel and remove.Open doors and
end caps from each side of dash. Unsnap and
radio/instrument cluster panel. Remove (3)
in order to remove radio.
BUICK Rendevous 2002-2007
Disconnect the negative battery terminal to prevent an
accidental
1
Unsnap
bottom
Remove
short circuit. Remove screws in cup holder
and remove shifter. Remove (2) screws from
of radio/climate control bezel, unclip and remove.
(3) 7mm hex head screws to remove radio.
CHEVROLET Avalanche 2003-2006
1
Disconnect the negative battery terminal to prevent an
accidental short circuit. Unsnap and remove dash bezel.
Remove (3) 9/32" screws and remove radio.
BUICK Park Avenue 2000-2005
1
Disconnect
accidental
and
from
remove
instrument
radio.
1
the negative battery terminal to prevent an
short circuit. Open drivers door and unsnap
remove dash end cap. Remove (2) phillips screws
underneath steering column cover. Unsnap and
steering column cover. Unsnap and remove
panel. Remove (2) 9/32" screws and remove
1
CHEVROLET Cavalier 2000-2005
Disconnect the negative battery terminal to prevent an
accidental
panel
remove
from
glove
of
defroster
exposed. Remove
exposed
short circuit. Open driver door and remove fuse
on the end of dash. Open passenger door and
panel on end of dash. Remove (1) phillips screw
each side exposed. Remove (3) screws from top of
box liner. Remove (2) screws from the top-left corner
the glove box cavity. Remove (1) phillips screw from the
duct Remove the duct work and (1) phillips screw
the dash pad and (3) phillips screws
at the top of the radio trim bezel.
6
Loading...