Metra Electronics 99-3026B Installation Manual

Page 1
CAUTION!
All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.
Metra. The World’s Best Kits.
MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 6/28/18 INST99-3026B
INSTALLATION INSTRUCTIONS
99-3026B
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Complete center dash panel for a factory look
• Painted matte black
KIT COMPONENTS
• A) Radio/climate control panel • B) Radio brackets • C) Climate control trim panel A (04-05) • D) Climate control trim panel B (06-09)
• E) Pocket • F) (6) Panel clips • G) (12) #8 x 3/8” Phillips screws
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32” Socket wrench
TABLE OF CONTENTS
Dash Disassembly ...............................................2-3
Kit Preparation ...................................................4-5
Kit Assembly
–ISO DIN radio provision with pocket ..................6
–ISO DDIN radio provision .....................................7
WIRING & ANTENNA CONNECTIONS
Wiring Harness: TBA Antenna Adapter: 40-GM10
Steering wheel control interface: • ASWC-1 (sold separately)
A B C
GF
D E
Cadillac XLR 2004-2009
Page 2
1.800.221.0932 | MetraOnline.com
2
1. On the bottom of the shifter, pull the chrome trim downward, and then remove (1) screw exposed. Pull up on the shifter to remove it. (Figure A)
2. Unclip the shifter trim plate, then set to the side. (Figure B)
Continued on the next page
DASH DISASSEMBLY
(Figure B)(Figure A)
Page 3
REV. 6/28/2018 INST99-3026B
3
DASH DISASSEMBLY
(CONT.)
3. Unclip, unplug, and remove the radio/ climate control panel. (Figure C)
4. Remove (4) 9/32” screws securing the radio. Slide the radio out, then unplug and remove the radio. (Figure D)
Continue to Kit Preparation
(Figure D)(Figure C)
Page 4
1.800.221.0932 | MetraOnline.com
4
KIT PREPARATION
From the factory radio/climate control panel:
1. Unclip and remove the a/c vents.
(Figure A)
2. Unclip and remove the hazard switch. (Figure A)
3. Remove (4) screws securing the climate controls, then remove the controls. (Figure A)
Continued on the next page
(Figure A)
Page 5
REV. 6/28/2018 INST99-3026B
5
KIT PREPARATION
(CONT.)
4. Secure the appropriate
climate control
trim panel
to the
99-3026B radio/
climate control panel
using the (4)
#8 x 3/8” Phillips screws provided. The
climate control panel
part number is
stamped onto the back of the panel.
CH-3026-1 - 2004-2005
CH-3026-2 - 2006-2009 (Figure A)
To the 99-3026B radio/climate control panel:
5. Secure the (6) included
panel clips
to the
radio/climate control panel
(factory clips
can also be used if desired) (Figure B)
6. Clip in the factory a/c vents. (Figure C)
7. Clip in the hazard switch. (Figure C)
8. Secure the climate controls to the panel
using the (4) #8 x 3/8” Phillips screws provided. (Figure C)
Continue to Kit Assembly
(Figure A) (Figure B) (Figure C)
Page 6
1.800.221.0932 | MetraOnline.com
6
KIT ASSEMBLY
ISO DIN radio provision with pocket
1. Secure the
radio brackets
to the
pocket
using the (4) #8 x 3/8” Phillips screws provided. (Figure A)
2. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
3. Slide the radio into the bracket/pocket assembly, then secure it to the assembly using the screws supplied with the radio. (Figure B)
4. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/ or Axxess. Test the radio for proper operation.
5. Secure the radio assembly to the dash using the factory screws.
6. Reassemble the dash in reverse order of disassembly to complete the installation.
(Figure A) (Figure B)
Page 7
REV. 6/28/2018 INST99-3026B
7
(Figure A)
ISO DDIN radio provision
1. Secure the
radio brackets
to the radio using the screws supplied with the radio. (Figure A)
2. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.
3. Secure the radio assembly to the dash using the factory screws.
4. Reassemble the dash in reverse order of disassembly to complete the installation.
KIT ASSEMBLY
Page 8
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
®
Metra recommends MECP certified technicians
IMPORTANT If you are having difficulties with the installation of this product,
please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
Metra. The World’s Best Kits.
MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 6/28/18 INST99-3026B
INSTALLATION INSTRUCTIONS
99-3026B
Loading...