Metra Electronics 95-8224 User Manual

Page 1
INSTALLATION INSTRUCTIONS FOR PART 95-8224
APPLICATIONS
Toyota Matrix 2009-10
Pontiac Vibe 2009-10
(Excluding Factory Navigation Models)
95-8224
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
B
ness & Antenna Connections (sold separately)
Har
• 70-1761 - Toyota Harness 87-up
TOOLS REQUIRED:
• Socket Set
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
Page 2
95-8224
TABLE OF CONTENTS
Dash Disassembly
-
Toyota Matrix/Pontiac Vibe 2009-10 . . . . . . . . . . . . .
. . . . . . 1
Kit Preparation
...........................
. . . . . . . . . . . . .2
Kit Assembly
- Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Final
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
*Note: Refer also to the instructions included with the aftermarket radio.
Page 3
95-8224 DASH DISASSEMBLY
P
ASSENGER
SECURITY
A
/C
0
1
2
3
4
5
Toyota Matrix/Pontiac Vibe 2009-10
1
Disconnect the negative battery ter­minal to prevent an accidental short circuit.
Unclip and remove the radio trim
2
panel including the a/c vent. (
Remove (4) 10 MM bolts securing the
3
Figure A)
radio. Unplug and remove the radio.
(Figure B)
Continue to kit preparation.
A
B
1
Page 4
95-8224 KIT PREPARATION
DOUBLE DIN RADIO PROVISION
STACKED ISO MOUNT UNITS
*Note: Refer also to the instructions included with the aftermarket radio.
A
Snap the Double DIN Trim plate into
1
the rear of the factory radio trim panel.
(Figure A)
Continue to kit assembly.
2
Page 5
95-8224 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
STACKED ISO MOUNT UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
Attach the Double DIN brackets to the Double DIN or the stacked ISO mount unit(s) using the screws supplied with the unit(s).
Continue to final assembly.
(Figure A)
3
Page 6
95-8224 FINAL ASSEMBLY
FINAL ASSEMBLY
A
(A) Strip wire ends back 1/2"
B
B) Twist ends together
C) Solder
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
1
proper mating adapter and making connections as shown. (Isolate and individ­ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
2
Reassemble radio and dash assemblies in reverse order of disassembly.
3
D) Tape
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
Page 7
95-8224
NOTES
5
Page 8
95-8224 INSTRUCTIONS
1-800-221-0932
REV. 04/27/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST95-8224
www.metraonline.com
Loading...