Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
*Note:
Refer also to the instructions included with the aftermarket radio.
95-7951 DASH DISASSEMBLY
CHEVROLET AVEO 2004-2006
CHEVROLET AVEO HATCHBACK 2007
PONTIAC G3 HATCHBACK 2007
Disconnect the negative battery ter-
1
minal to prevent an accidental short
circuit.
Unclip and remove the trim panels
2
from both sides of radio/climate con-
Figure A)
trols. (
Remove (4) Phillips screws securing
3
the radio. Unplug and remove radio.
(
Figure B)
A
Continue to kit assembly.
B
1
95-7951 DASH DISASSEMBLY
Inside of Glove Box
AM/FM
TAPE
CD
TUNE
1
2
3
4
5
6
BASS
MUTE
EQ
AST
SCAN
SUZUKI FORENZA 2004-2008
SUZUKI RENO 2005-2008
Disconnect the negative battery ter-
1
minal to prevent an accidental short
circuit.
Disconnect air selector cable on dri-
2
ver’s side of center console behind
dash above accelerator pedal.
Figure A & B)
(
3
Open glove box and remove (5)
Phillips screws ((3) on top and (2) on
bottom) then remove entire glove box.
Disconnect temperature selector
4
cable on passenger side of center
console behind glove box. (
Unsnap and remove entire panel sur-
5
Figure C)
rounding radio. NOTE: The clips holding radio panel to dash are very
strong. (
Remove (4) 10 MM bolts securing
6
Figure D)
radio. Unplug and remove radio.
Figure E)
(
A
B
C
Continue to kit assembly.
D
E
2
95-7951 DASH DISASSEMBLY
SUZUKI VERONA 2004-2007
Disconnect the negative battery ter-
1
minal to prevent an accidental short
circuit.
Unclip and remove the trim panel sur-
2
rounding the radio. (
Remove (4) Phillips screws from
3
radio. Unplug and remove radio.
(
Figure B)
Continue to kit assembly.
Figure A)
A
B
3
95-7951 KIT ASSEMBLY
CUT
HERE
ON BOTH SIDES
DOUBLE DIN MOUNT RADIO PROVISION
*
Note: Refer also to the instructions included with the aftermarket radio.
NOTE: For the Chevrolet Aveo 2004-06,
Chevrolet Aveo Hatchback 2007, Pontiac
G3 Hatchback 2007 and Suzuki Verona
2004-07, cut and remove front lower mounting tabs from the Double DIN trim plate
(Figure A). For the Suzuki Forenza 2004-07 and
the Suzuki Reno 2005-07, cut the rear lower
mounting tabs (Figure B).
NOTE: The Verona 2004-2007 sub dash
will need to be trimmed slightly for proper
fit. Refer to illustration.
(Figure C,D)
1
Snap the Double DIN brackets to the outside edge of the Double DIN trim plate.
(Figure E)
Slide the Double DIN radio into the brack-
2
et/trim plate assembly and secure the
radio to the assembly using the screws
supplied with the radio.
(Figure F)
Continue to final assembly.
C
A
B
D
E
F
4
95-7951 KIT ASSEMBLY
CUT
HERE
ON BOTH SIDES
STACKED ISO MOUNT UNITS PROVISION
*
Note: Refer also to the instructions included with the aftermarket radio.
NOTE: For the Chevrolet Aveo 2004-06,
Chevrolet Aveo Hatchback 2007, Pontiac
G3 Hatchback
2004-07, cut and remove front lower mounting tabs from the Double DIN trim plate
(Figure A). For the Suzuki Forenza 2004-07 and
Suzuki Reno 2005-07, cut the rear lower
the
mounting tabs (Figure B).
NOTE: The Verona 2004-2007 sub dash will
need to be trimmed slightly for proper fit.
Refer to illustration.
(Figure C,D)
Snap the Double DIN brackets to the out-
1
side edge of the Double DIN trim plate.
(Figure E)
Slide the stacked ISO units into the brack-
2
et/trim plate assembly and secure the units
to the assembly using the screws supplied
with the units.e
(Figure F)
2007 and Suzuki Verona
A
B
Continue to final assembly.
C
E
D
F
5
95-7951 FINAL ASSEMBLY
FINAL ASSEMBLY
A
(A) Strip wire ends back 1/2"
B
B) Twist ends together
C) Solder
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
1
proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
2
Reassemble radio and dash assemblies in reverse order of disassembly.
3
D) Tape
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White