INSTALLATION INSTRUCTIONS FOR PART 95-7866B
APPLICATIONS
ACURA MDX 2001-2006
95-7866B
KIT FEATURES
• Double DIN Head Unit Provision
• ISO Stacked Head Unit Provision
• Painted Matte Black to Match Factory Dash
KIT COMPONENTS
A) Double DIN Radio Housing • B) DDIN Brackets (To hold Display above radio)
B
A
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
• 70-1721 Honda harness - 1998-up
• 40-HD10 -Honda antenna adapter- 2005-up
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Wrench
1-800-221-0932
© COPYRIGHT 2003-2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
95-7866B
K
NOWLEDGE IS POWER
Enhance your installation and fabrication skills
by enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 for more information
and take steps toward a better tomorrow.
TABLE OF CONTENTS
Dash Disassembly
-
ACURA MDX 2001-2006.........................
. . . . . . 1
Kit Preparation
- Display Unit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Kit
Assembly
- Double DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- ISO Stacked Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
*Note:
Refer also to the instructions included with the aftermarket radio.
95-7866B DASH DISASSEMBLY
ACURA MDX 2001-2006
Disconnect the negative battery
1
terminal to prevent an accidental
short circuit.
Unclip and remove trim panel around
2
radio/display including a/c vents.
Figure A)
(
Remove (6) mounting screws and
3
remove the audio/display unit from
the dash. (
Remove (8) screws from the audio
4
unit and (4) screws from the display
unit and remove the brackets from
the audio/display assembly.
Continue to kit preparation.
Figure B)
A
B
1
95-7866B KIT PREPARATION
DISPLAY UNIT ASSEMBLY
*
Note: Refer also to the instructions included with the aftermarket radio.
A
Using the mounting screws from the
1
display unit, attach the brackets
supplied with the kit by aligning the
guide pins on the display with the
holes on the brackets.
Align guide pins on bottom of display
2
unit with holes on top of housing and
attach the unit to the housing using
the (2) screws previously removed.
(Figure B)
Continue to kit assembly.
(Figure A)
2
B
95-7866B KIT ASSEMBLY
DOUBLE DIN HEAD UNIT PROVISION/
ISO STACKED HEAD UNIT PROVISION
*
Note: Refer also to the instructions included with the aftermarket radio.
A
1
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from
Metra or AXXESS. Re-connect the
negative battery terminal and test
the unit for proper operation.
2
Slide the Double DIN head unit or
stacked ISO head units into the
bracket/radio housing assembly and
secure the Double DIN head unit or
stacked ISO head units to the
assembly using the screws supplied
with the radio.
3
Reassemble dash in reverse order of
disassembly.
(Figure A)
3
95-7866B
NOTES
4
95-7866B
NOTES
5
95-7866B INSTRUCTIONS
1-800-221-0932
REV. 08/24/09 © COPYRIGHT 2003-2009 METRA ELECTRONICS CORPORATION INST99-7866B
www.metraonline.com
Loading...