INSTALLATION INSTRUCTIONS FOR PART 95-7331
APPLICATIONS
KIA Amanti
2007-2009
95-7331
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Radio Housing B) Double DIN Brackets
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket set
1-800-221-0932
© COPYRIGHT 2007-2008 METRA ELECTRONICS CORPORA
B
www.metr
aonline.com
TION
95-7331
K
NOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
TABLE OF CONTENTS
Dash Disassembly
- KIA Amanti 2007-2009.......................................... 1,2
Kit Assembly
- Double DIN Radio Provision /Stacked ISO Mount Units Provision . . . . . . . . .3
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
*Note:
Refer also to the instructions included with the aftermarket radio.
95-7331 DASH DISASSEMBLY
1
2
3
KIA AMANTI 2007-2009
Disconnect the negative battery ter-
1
minal to prevent an accidental short
circuit.
Unclip the top half of the shift knob
2
and remove the “C” clip securing the
shifter. Pull up on shifter to remove.
(Figure A)
Unclip and remove the panel surround-
3
ing the shifter.
Unclip and remove top half of center
4
console including the cup holders.
(Figure C)
Open center console and remove
5
screw cover in bottom.
Remove (2) 10 MM bolts securing
6
compartment then unclip and remove
the compartment.
(Figure B)
(Figure D)
(Figure D)
A
B
Continue to kit assembly.
CD
1
95-7331 DASH DISASSEMBLY
KIA AMANTI 2007-2009
Unclip the rear trim panel from the
7
center console including a/c vents.
Unplug and remove the rear trim
(Figure E)
panel.
Remove (1) Phillips screw from each
8
side at the rear of the center console.
(Figure E)
Unclip the side panels from the front of
9
the center console. It is not necessary
to remove these panels.
Remove (4) Phillips screws securing
10
center console then lift and slide the
center console back out of the way.
Note: You do not have to take the center console all the way out.
Remove (1) Phillips screw from each
11
side panel then unclip and remove
the side panels.
(Figure H)
(Figure F)
(Figure G)
E
F
Remove (4) Phillips screws securing
12
the radio. Unplug and remove the
radio.
Unclip and remove the switches and/
13
or switch covers along the top of the
factory radio. (Retain switches
and/or covers to be reinstalled in
the radio housing.)
Continue to kit assembly.
H
G
2
95-7331 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
STACKED ISO MOUNT UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
Snap the switches into the radio hous-
1
ing in the same location as removed
from the factory radio.
Snap the Double DIN brackets to the
2
inside edge of the Radio Housing.
(Figure B)
Slide the Double DIN Radio or stacked
3
ISO Mount units into the bracket/radio
housing assembly and secure to the
assembly using the screws supplied
with the radio or ISO mount units.
(Figure C)
Continue to final assembly.
(Figure A)
A
B
3
C
95-7331 FINAL ASSEMBLY
FINAL ASSEMBLY
A
(A) Strip wire ends back 1/2"
B
B) Twist ends together
C) Solder
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
1
proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
2
Reassemble radio and dash assemblies in reverse order of disassembly.
3
D) Tape
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . .
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Orange
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+)
Left Rear (-) . . . . . . . . . . . . . . Green / Black
. . . . . . . . . . . . .
Green
*NOTE: When a Black wire is not present,
All colors may not be present on all leads due to manufacturer’s specifications.
ground radio to vehicle chassis.
4
95-7331
NOTES
5
95-7331 INSTRUCTIONS
1-800-221-0932
REV. 09/12/08 © COPYRIGHT 2007-2008 METRA ELECTRONICS CORPORATION INST95-7331
www.metraonline.com
Loading...