Page 1
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.
®
MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/5/18 INST95-6546B
INSTALLATION INSTRUCTIONS
95-6546B
KIT FEATURES
• ISO DDIN radio provision
• Painted matte black
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) (2) Panel clips
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Cutting tool • Grinding tool
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness:
70-1817 (99-01) • 70-6502 (02-04)
Antenna Adapter:
N/A (99-01) • 40-CR10 (02-04)
A B C
Jeep Grand Cherokee 1999-2004
Page 2
1.800.221.0932 | MetraOnline.com
2
1. Unclip and remove the radio trim panel.
(Figure A)
2.
Remove (4) Phillips screws securing the
radio, then unplug and remove the radio
.
Continue to Kit Preparation
1.
Carefully grind or cut away the (4) plastic
welded tabs securing the a/c vents to the
radio trim panel, then remove the vents.
(Figure A)
2.
Trim the top of the a/c vents. (Figure B)
3.
Attach the a/c vents to the radio trim
panel, then secure them by either gluing
them, or plastic welding them in place.
Note:
Once the radio trim panel is
secured to the vehicle, this will also hold
the vents in place.
4.
Attach the (2)
panel clips
provided onto
the
radio trim panel
.
5.
Cut the sub-dash to allow room for the
radio assembly. (Figure C)
Continue to Kit Assembly
(Figure A)
DASH DISASSEMBLY KIT PREPARATION
(Figure A)
(Figure B)
(Figure C)
Remove shaded area
Page 3
REV. 4/5/2018 INST95-6546B
3
(Figure A)
1. Secure the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure A)
2. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
3. Secure the radio assembly to the dash
using the factory screws.
4. Snap the
radio trim panel
over the radio
assembly to complete the installation.
KIT ASSEMBLY
Page 4
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
IMPORTANT
If you are having difficulties with the installation of this product,
please call our Tech Support line at 1-800-253-TECH. Before
doing so, look over the instructions a second time, and make
sure the installation was performed exactly as the instructions
are stated. Please have the vehicle apart and ready to perform
troubleshooting steps before calling.
Metra. The World’s Best Kits.
®
MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/5/18 INST95-6546B
INSTALLATION INSTRUCTIONS
95-6546B
Loading...