Metra Electronics Ford F-150 2009-up, 95-5819 Installation Manual

Page 1
METRA. The World’s best kits.
metraonline.com1-800-221-0932
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
REV. 2/12/2014 INST95-5819
CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the aftermarket radio.
INSTALLATION INSTRUCTIONS FOR PART 95-5819
• A) Double DIN radio housing • B) Double DIN brackets
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness:
• 70-5520 - Ford 2003-up
Antenna Adapter:
• 40-CR10 - Chrysler 2002-up
• Cutting tool • Phillips screwdriver
• Socket wrench
TOOLS REQUIRED
A B
• Double DIN radio provision
KIT FEATURES
Ford F-150 2009-up (only XL models without plus package)
95-5819
Page 2
2
Dash Disassembly
– Ford F-150 2009-up (only XL models without plus package) .................................. 2-3
Kit Assembly
– Double DIN radio provision ..................................................................................3
Table of Contents
1. Unclip and remove the switch panel to the right of the cigarette lighter then remove the (1) 9/32” screw exposed. (Figure A)
2. Remove the rubber pad at the top of the radio trim panel then remove the (2) 9/32” screws exposed. (Figure B)
3. Remove (4) 10 mm hex head screws securing the factory radio. Unplug wiring and remove radio.
Continue on next page
Ford F-150 2009-up
(only XL models without plus package)
(Figure B)
(Figure A)
95-5819 Dash Disassembly 95-5819
Page 3
3
Dash Disassembly 95-5819
4. Unclip and pull the side panels containing the A/C vents away from the radio trim panel. (Figure C)
Note: It is not necessary to remove
the panels completely.
5. Unclip and remove the radio trim panel. (Figure D)
6. Remove (4) 9/32” screws to remove the factory radio.
Continue to kit assembly
Ford F-150 2009-up
(only XL models without plus package)
1. Slide the appropriate side bracket over the mounting legs of the double DIN trim plate aligning the holes in the trim plate and the bracket and rotate inward.
Note: The notch in the housing should be on top. (Figure A)
2. Slide the double DIN radio into the bracket/radio housing assembly and secure the double DIN radio to the assembly using the screws supplied with the radio. (Figure B)
Continue on back page
(Figure B)
Double DIN radio provision
(Figure A)
(Figure D)
(Figure C)
Kit Assembly 95-5819
Page 4
METRA. The World’s best kits.
metraonline.com1-800-221-0932
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
REV. 2/12/2014 INST95-5819
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
Metra recommends MECP certified technicians
INSTALLATION INSTRUCTIONS FOR PART 95-5819
3. Cut and remove half of the top (2) mounting legs with the brackets attached. (Figure C)
4. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
5. Reassemble dash in reverse order of disassembly.
(Figure C)
Double DIN radio provision
CUT HERE -
CUT HERE
TOP LEG ONLY
TOP LEG ONLY
CUT
CUT
Cut here - Top leg only
Cut here - Top leg only
Cut
Cut
Loading...