Page 1
INSTALLATION INSTRUCTIONS FOR PART 95-3527
95-3527
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Units Provision
• A) Radio Housing • B) Double DIN Brackets • C) Double DIN Trim Plate
KIT COMPONENTS
A
Phillips Screwdriver • Panel Removal Tool
• Socket Set
1-800-221-0932
© COPYRIGHT 2004-07 METRA ELECTRONICS CORPORA
TION
www.metr
aonline.com
TOOLS REQUIRED:
APPLICATIONS
Pontiac Grand Prix
2004-2007
B C
Page 2
Dash Disassembly
- Pontiac Grand Prix 2004-07 .......................................1
Kit
Assembly
- Double DIN Radio Provision .......................................2
- Stacked ISO Units Provision.......................................3
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TABLE OF CONTENTS
95-3527
*Note:
Refer also to the instructions included with the aftermarket radio.
Page 3
95-3527 DASH DISASSEMBLY
PONTIAC GRAND PRIX 2004-07
A
B
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Remove trim ring around key cylinder.
(Figure A)
2
Unclip and remove entire panel surrounding radio including message
center and vents.
(Figure B)
3
To remove radio start at bottom of
stack and remove (8) 9/32” screws
from pocket, climate control, and
radio (4) on each side).
(Figure C)
4
Continue to kit assembly.
C
Page 4
2
95-3527 KIT ASSEMBLY
B
A
DOUBLE DIN RADIO PROVISION
Slide the Double DIN radio into the
Double DIN bracket/radio housing
assembly and secure the unit to the
kit using the screws supplied with
the radio.
(Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure A)
1
Snap the Double DIN trim-plate onto
the front of the housing/radio assembly.
(Figure B)
3
Page 5
3
95-3527 KIT ASSEMBLY
B
A
STACKED ISO UNITS PROVISION
Slide the stacked ISO units into the
Double DIN bracket/radio housing
assembly and secure the units to the
kit using the screws supplied with the
units.
(Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure A)
1
Snap the Double DIN trim-plate onto
the front of the housing/radio assembly.
(Figure B)
3
Page 6
95-3527 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
4
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer
. . . . . . . . . . . . . . . . .
Orange /
White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-)
. . . . . . . . . . . . . .
Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
Page 7
95-3527
NOTES
5
Page 8
95-3527 INSTRUCTIONS
1-800-221-0932
REV. 06/19/07 © COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION INST95-3527
www.metraonline.com
Loading...