Metra Electronics 88-00-8000, AW-800PKUV Installation Manual

Page 1
88-00-8000 AW-800PKUV
INSTALLATION INSTRUCTIONS
APPLICATIONS
CAR PAGE
TOYOTA
KIT FEATURES
Works with factory brackets or Metra's 99-8101
Fills space left after removing double-DIN unit
KIT COMPONENTS
TOOLS REQUIRED
Cutting tool
Phillips screwdriver
KIT FEATURES
Pocket
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the ashtray and (3) screws from the ashtray bracket. Remove (1) screw from each side of the dash console and unsnap the trim bezel.
1
TOYOTA 4Runner 1984-88
2
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the driver's side speaker panel by removing (3) screws and (1) 10mm bolt. Remove (1) screw from the left side of the housing and unsnap the ignition cover. Remove the glove compartment assembly by removing (1) 10mm bolt from the bottom of the speaker panel and (3) screws from the right side of the housing. Remove the remaining (3) screws securing the radio trim bezel.
1
TOYOTA 4Runner 1989-95
1
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
2
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
USE THE FOLLOWING INSTRUCTIONS FOR APPLICATIONS USING FACTORY BRACKETS. FOR APPLICATIONS USING METRA'S 99- 8101, USE THE INSTRUCTIONS PROVIDED WITH THAT KIT.
Page 2
Disconnect the negative battery terminal to prevent an accidental short circuit. Open the center armrest door. Unsnap the parking brake trim panel to access the gear shifter trim panel. Unsnap the gear shifter trim panel and remove. Remove the climate control knobs. Remove the climate control trim plate and (2) Phillips screws exposed. Unclip the radio trim bezel and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring.
1
TOYOTA 4Runner 1996-99
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) screws above the climate controls and gently unsnap the dash trim bezel. Remove (4) screws securing the factory head unit and disconnect the wiring.
1
TOYOTA Camry 1987-91
2
2
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
2
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) screws from the lower steering column panel and remove. Remove the (2) screws exposed on the radio trim bezel. Open the glove box and remove (1) screw and (1) bolt exposed. Remove (2) screws from the ash­tray cavity and (2) screws from the bracket. Remove (2) screws from each lower side of the trim bezel and unsnap the bezel.
1
TOYOTA Celica (GT/GTS) 1986-89
Disconnect the negative battery terminal to prevent an accidental short circuit. Carefully pry up on the gear shifter trim panel and remove. Remove (2) screws exposed on the bottom edge of the radio trim panel. Unsnap the panel and disconnect the ashtray and cigarette lighter wiring.
1
TOYOTA Celica 1990-93
3
2
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
2
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
Page 3
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (1) screw located to the right of the ignition switch. Remove (1) screw located above the driver's side speaker. Carefully unsnap the dash trim bezel (some force may be required).
1
TOYOTA Corolla (sed/wag-lower dash) 1988-92
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) Phillips screws from each side of the console trim bezel. Remove (4) screws securing the factory head unit and disconnect the wiring.
1
TOYOTA Corolla (GTS/SR5) 1984-87
4
2
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
2
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the climate control knobs, unsnap the upper trim bezel and disconnect the hazard and clock leads. Remove (2) screws from the lower trim bezel and remove.
1
TOYOTA Corolla (coupe-lower dash) 1993-97
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (4) screws from the top edge of the instrument trim bezel and (2) screws below the radio opening. Remove (1) screw from the lower-left tab of the bezel ( to the right of the a/c vent) and unsnap the bezel.
1
TOYOTA Corolla (sed/wag-upper dash) 1988-92
5
2
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
2
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
Page 4
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the climate control knobs and unsnap the dash trim bezel. Disconnect the clock and hazard leads.
1
TOYOTA Corolla (coupe-upper dash) 1993-97
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the ashtray and (2) screws from the ashtray cavity. Unsnap and remove the shifter console bezel. Remove (1) screw below the ignition switch and remove the dash trim bezel.
1
TOYOTA MR2 1991-94
6
2
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
2
Remove the mounting brackets from the factory head unit assembly. Align the holes in the mounting brackets with the holes in the Pocket. Mount the factory mounting brackets to the Pocket with those screws previously removed.
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the ashtray and (3) screws from the ashtray bracket. Remove (1) screw from each side of the dash console and unsnap the trim bezel.
1
TOYOTA Pickup 1984-88
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the driver's side speaker panel by removing (3) screws and (1) 10mm bolt. Remove (1) screw from the left side of the housing and unsnap the ignition cover. Remove the glove compartment assembly by removing (1) 10mm bolt from the bottom of the speaker panel and (3) screws from the right side of the housing. Remove the remaining (3) screws securing the radio trim bezel.
1
TOYOTA Pickup 1989-91
7
2
Loading...